Flatbed / terpal

Fliegl SDS 390 MegaRunner X traLong 15030

Further information
Chassis saddle forwarding
Fine-grained steel welded construction, with preload slight pre-tensioning in the neck area, saddle plate with replaceable 2 kingpins
X-tra Long, with 15030 mm internal length
Outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment
Fsdei Riwuepfx Adqsgh
24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation
Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm
Extension ladder at the rear
Door retainer at the side
2 wheel chocks with holder
Aluminium side bumper
Galvanized steel underride guard
Quarter-shell mudguards in front of 1st axle and behind each axle
Impact protection at the rear
Axles + suspension
SAF disc brake axles
Axle/chassis laser-measured Reduction of tire wear and fuel consumption
Air suspension
Brake system
2-line compressed air brake system
Colored line routing for easy service.
Spring-loaded parking brake
2 interchangeable clutch heads at the front, without connecting cable
EBS, electronic braking system with EBS socket at the front, without connecting cable
Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS!
with lifting & lowering valve
Vehicle stability system
AAC Basic, automatic relief axle acting on last axle, as maneuvering aid, up to 20 km/h, can be switched off manually
Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales)
Wheels and tires
435/50 R19.5 tires of the manufacturer's choice
Steel rims, factory silver
Electrical system
24 volt, multi-chamber lights, amber LED lighting on the side
Side amber LED lighting coupled with the blinker Flashing side lights
Side lights
2 white position lights at the front
2 white/red rear lane departure lights
2 x 7-pin interchangeable sockets at the front, without connecting cable
Floor
Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg
Front wall / front corner stanchions
2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection
Center stanchions
3 pairs of sliding stanchions can be moved along the entire length, with 4-fold
pockets and with long pocket at the bottom.
3 pairs of stanchion positions
Insertion slats
5 rows of wooden slats
Rear wall / rear corner stanchions
Rear corner stanchions steel up to lower edge of roof, attachment for tarpaulin with round tube
and tarpaulin tensioning ratchet
Rear portal doors, 2-leaf with 2 internal espagnolette locks each
Tarpaulin
Tarpaulin, with welded-in horizontal and vertical straps
Stainless steel tension locks
Roof
Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails
approx. 2,490 mm, tarpaulin color: white
Roof non-elastic, hardly any deflection of the roof rail when loading and unloading
EcoLift - lifting roof can be raised by approx. 380 mm, on both sides, with gas pressure damper support,
3 driving positions at the front:
Front interior height approx. 2900 mm / 2950 mm / 3000 mm,
adjusted to approx. 3000 mm
Optimum rain strip at the rear, at the top of the end bows,

Iklan ini diterjemahkan secara otomatis. Kesalahan terjemahan mungkin terjadi.