Trailer gandeng low loaderMÜLLER-MITTELTAL
3-Achs-Tiefladeanhänger
Trailer gandeng low loader
MÜLLER-MITTELTAL
3-Achs-Tiefladeanhänger
harga tetap ditambah PPN
€28.500
Kondisi
Bekas
Lokasi
Essen 

Gambar menunjukkan
Tampilkan peta
Data mesin
- Nama mesin:
- Trailer gandeng low loader
- pabrikan:
- MÜLLER-MITTELTAL
- Model:
- 3-Achs-Tiefladeanhänger
- Kondisi:
- bekas
Harga & Lokasi
harga tetap ditambah PPN
€28.500
- Lokasi penjual:
- Heegstraße 6-8, 45356 Essen, Jerman
Hubungi
Rincian teknis
- Berat keseluruhan:
- 30.000 kg
- Berat muatan maksimum:
- 23.850 kg
- Konfigurasi gandar:
- 3 gandar
- Lebar ruang muat:
- 2.520 mm
- Pendaftaran pertama:
- 05/2022
- Inspeksi berikutnya (TÜV):
- 06/2025
- Lebar total:
- 2.520 mm
- Perlengkapan:
- ABS
Rincian penawaran
- ID iklan:
- A19485411
- Nomor referensi:
- 30561
- pembaruan:
- terakhir pada 09.07.2025
Deskripsi
More vehicles available at
Excerpt from the equipment list. Complete equipment details on request.
* Hinged lid (hot-dip galvanized) for the toolbox on the turntable platform
* 1 removable rotating beacon (warning light), including holder and installation
* Warning package for special permit § 70 StVZO
* GIGANT axles, 17.5 inch
* Mechanical equalizer suspension with parabolic springs, rear
La-Si package
* 2 pcs UVV lashing eyes approx. LC 6,400 daN on the turntable platform, front left and right on the main frame
* 4 pcs UVV lashing eyes approx. LC 13,400 daN hanging in the outer frame, 2 pcs ahead of the minor drop on the turntable platform, 2 pcs ahead of the rear crossmember
* 6 pcs UVV lashing rings approx. LC 10,000 daN, pivotable and lowerable, loadable in all directions, 2 pcs after the minor drop, 2 pcs center of the low-bed platform, 2 pcs between the rear axles
* Wooden floor, clamped version
* Folding, galvanized outriggers and wooden planks for widening (not applicable at the rear slope)
* Plank holder under the chassis lengthwise (maximum load width 2,500 mm)
* Continuous excavator arm storage above the rear axle up to the rear end crossmember, total length approx. 2,100 mm; crossmember at the approach slope, tapered, width top/bottom approx. 780/400 mm, height approx. 170 mm
* 2 pairs of lashing eyes approx. LC 6,400 daN in the excavator arm storage, welded to the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the slope
* Spare wheel holder under the chassis, without spare wheel
* Toolbox made of black powder-coated sheet steel, lockable, dimensions: approx. W=650 x H=300 x D=600 mm (up to approx. 45 kg payload with even loading) on the right-hand side in direction of travel
* Drawbar approx. 150 mm offset with swiveling towing eye 40/50 mm (without 8° eye, mind the coupling height), base length approx. 1,800 mm
Note: The underrun protection of the truck must be ahead of the coupling point; otherwise, there is an increased risk of collision! D = 125 / 160 kN
* Chassis and turntable hot-dip galvanized (without top coat)
* Drawbar, turntable, axles with springs, as well as air reservoirs finished in black
Towing vehicle
* Coupling height: Standard approx. 840 - 1,025 mm unladen
Electrics
Dkelhccqswwy Ddetep
* 24 volts, 15-pin
Compressed air
* red/yellow
Paintwork
* Wheels: silver
* Chassis/turntable: hot-dip galvanized
* Drawbar, turntable, axles with springs, air reservoirs: black
* Painted galvanized outer frame left and right: RAL3002 Carmine Red
* Ramps: hot-dip galvanized
Iklan ini diterjemahkan secara otomatis. Kesalahan terjemahan mungkin terjadi.
Excerpt from the equipment list. Complete equipment details on request.
* Hinged lid (hot-dip galvanized) for the toolbox on the turntable platform
* 1 removable rotating beacon (warning light), including holder and installation
* Warning package for special permit § 70 StVZO
* GIGANT axles, 17.5 inch
* Mechanical equalizer suspension with parabolic springs, rear
La-Si package
* 2 pcs UVV lashing eyes approx. LC 6,400 daN on the turntable platform, front left and right on the main frame
* 4 pcs UVV lashing eyes approx. LC 13,400 daN hanging in the outer frame, 2 pcs ahead of the minor drop on the turntable platform, 2 pcs ahead of the rear crossmember
* 6 pcs UVV lashing rings approx. LC 10,000 daN, pivotable and lowerable, loadable in all directions, 2 pcs after the minor drop, 2 pcs center of the low-bed platform, 2 pcs between the rear axles
* Wooden floor, clamped version
* Folding, galvanized outriggers and wooden planks for widening (not applicable at the rear slope)
* Plank holder under the chassis lengthwise (maximum load width 2,500 mm)
* Continuous excavator arm storage above the rear axle up to the rear end crossmember, total length approx. 2,100 mm; crossmember at the approach slope, tapered, width top/bottom approx. 780/400 mm, height approx. 170 mm
* 2 pairs of lashing eyes approx. LC 6,400 daN in the excavator arm storage, welded to the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the slope
* Spare wheel holder under the chassis, without spare wheel
* Toolbox made of black powder-coated sheet steel, lockable, dimensions: approx. W=650 x H=300 x D=600 mm (up to approx. 45 kg payload with even loading) on the right-hand side in direction of travel
* Drawbar approx. 150 mm offset with swiveling towing eye 40/50 mm (without 8° eye, mind the coupling height), base length approx. 1,800 mm
Note: The underrun protection of the truck must be ahead of the coupling point; otherwise, there is an increased risk of collision! D = 125 / 160 kN
* Chassis and turntable hot-dip galvanized (without top coat)
* Drawbar, turntable, axles with springs, as well as air reservoirs finished in black
Towing vehicle
* Coupling height: Standard approx. 840 - 1,025 mm unladen
Electrics
Dkelhccqswwy Ddetep
* 24 volts, 15-pin
Compressed air
* red/yellow
Paintwork
* Wheels: silver
* Chassis/turntable: hot-dip galvanized
* Drawbar, turntable, axles with springs, air reservoirs: black
* Painted galvanized outer frame left and right: RAL3002 Carmine Red
* Ramps: hot-dip galvanized
Iklan ini diterjemahkan secara otomatis. Kesalahan terjemahan mungkin terjadi.
Penyedia
ES-GE Nutzfahrzeuge GmbH
Kontak person Tuan Markus Hurdelhey
Heegstraße 6-8
45356 Essen, Jerman
+49 201 8... iklan
Terdaftar sejak: 2003
Tampilkan lebih banyak

Als eingetragener Hersteller und herstellerunabhängiger Händler können wir zielgerichtete und effiziente Konzepte anbieten, sei es beim Fahrzeug selbst oder in den Bereichen Service, Miete und Mietkauf.
Seit Gründung der ES-GE im Jahr 1986 haben sich unsere angebotenen Leistungen stets an der Nachfrage des Marktes orientiert. Den reinen Handel von Spezial-Nutzfahrzeugen haben wir um deren Vermietung ergänzt. Heute bieten wir u.a. individuelle, flexible Mietkauf- und Finanzierungskonzepte an.
Wir sind in der Lage, bereits bei der Planung eines Neufahrzeugs auf Kundenwünsche einzugehen, um, je nach Fahrzeugtyp, Lösungen mit dem am besten geeigneten Hersteller umzusetzen. Unser großer Fahrzeugbestand bietet zugleich die Möglichkeit, lange Lieferzeiten zu vermeiden.
Seit Gründung der ES-GE im Jahr 1986 haben sich unsere angebotenen Leistungen stets an der Nachfrage des Marktes orientiert. Den reinen Handel von Spezial-Nutzfahrzeugen haben wir um deren Vermietung ergänzt. Heute bieten wir u.a. individuelle, flexible Mietkauf- und Finanzierungskonzepte an.
Wir sind in der Lage, bereits bei der Planung eines Neufahrzeugs auf Kundenwünsche einzugehen, um, je nach Fahrzeugtyp, Lösungen mit dem am besten geeigneten Hersteller umzusetzen. Unser großer Fahrzeugbestand bietet zugleich die Möglichkeit, lange Lieferzeiten zu vermeiden.
Tampilkan lebih banyak informasi hukum
Geschäftsführer: Marion Sucko, Markus Hurdelhey, Carsten Duwe
Postanschrift:
Postfach 45 02 21
45362 Essen
Deutschland
Anschrift Betriebsgelände:
Heegstr. 6 – 8
45356 Essen
Deutschland
Telefon: +49 (0) 201/61 67 - 0
Telefax: +49 (0) 201/61 67 - 160
Amtsgericht Essen HRB 7038
Zuständige Kammer: IHK Essen
Branche: Handel und Vermietung von Nutzfahrzeugen
UStId-Nr.: DE 119 668 255
Postanschrift:
Postfach 45 02 21
45362 Essen
Deutschland
Anschrift Betriebsgelände:
Heegstr. 6 – 8
45356 Essen
Deutschland
Telefon: +49 (0) 201/61 67 - 0
Telefax: +49 (0) 201/61 67 - 160
Amtsgericht Essen HRB 7038
Zuständige Kammer: IHK Essen
Branche: Handel und Vermietung von Nutzfahrzeugen
UStId-Nr.: DE 119 668 255
Tutup informasi hukum tambahan
Tampilkan lebih sedikit
Kirim permintaan
Telepon & Faks
+49 201 8... iklan
Iklan-iklan ini juga mungkin menarik bagi Anda.
iklan kecil

11.060 km
Trailer gandeng low loader
Müller MitteltalT 3 3 Achs Tieflader- Anhänger
Müller MitteltalT 3 3 Achs Tieflader- Anhänger
iklan kecil

11.013 km
Trailer gandeng low loader
MÜLLER-MITTELTALTiefladeanhänger T 3 Profi 30,0 Tiefladeranhänge
MÜLLER-MITTELTALTiefladeanhänger T 3 Profi 30,0 Tiefladeranhänge
iklan kecil

11.060 km
Trailer gandeng low loader
Müller MitteltalPT 30 3 Achs Tieflader 9,20 m Ladefläche
Müller MitteltalPT 30 3 Achs Tieflader 9,20 m Ladefläche
iklan kecil

11.060 km
Trailer gandeng low loader
Müller MitteltalPT 30 3 Achs Tieflader 9,20 m Ladefläche
Müller MitteltalPT 30 3 Achs Tieflader 9,20 m Ladefläche
iklan kecil

11.060 km
Trailer gandeng low loader
Müller MitteltalTe Kompakt 40,0 4 Achs Tiefladeranhänger
Müller MitteltalTe Kompakt 40,0 4 Achs Tiefladeranhänger
iklan kecil

10.918 km
Trailer gandeng low loader
MÜLLER-MITTELTALPT 3-Achser hydr. Rampen
MÜLLER-MITTELTALPT 3-Achser hydr. Rampen
iklan kecil

11.133 km
Trailer dump tiga arah
MÜLLER-MITTELTALTandem-3-Seiten-Kipper KA-TA-R 11,9
MÜLLER-MITTELTALTandem-3-Seiten-Kipper KA-TA-R 11,9
iklan kecil

10.778 km
Trailer dump tiga arah
MÜLLER-MITTELTALTA 11.9 t 3-Seiten Kipper
MÜLLER-MITTELTALTA 11.9 t 3-Seiten Kipper
iklan kecil

11.050 km
Trailer gandeng low loader
Müller-MitteltalT 3 Kompakt 30,0, Hydr. Rampen, Verbr. auf 3m
Müller-MitteltalT 3 Kompakt 30,0, Hydr. Rampen, Verbr. auf 3m
iklan kecil

11.060 km
Trailer gandeng low loader
Müller MitteltalT4 PROFI 40,0 4 Achs Tiefladeranhänger
Müller MitteltalT4 PROFI 40,0 4 Achs Tiefladeranhänger
Iklan Anda telah berhasil dihapus
Terjadi kesalahan