Mesin superfinishing

Nagel SE01-50-SO

Tahun pembuatan: 2011, Kondisi: sangat baik (bekas), Cloos welding robot Qirox QRC 320 incl. V6 control unit, Kjdpfxeizwv No Ac Hodr base pedestal for upright installation, Cloos welding machine Quinto II 603 (600 A), wire feeder, welding torch, torch hose package, mechanical cleaning, pressure booster 1 rotary-tilt table WPK 5000, load capacity 500 kg, 1 job selection panel, 1 control unit for customer-supplied sliding door gas nozzle sensor, arc seam tracking, point editor The system will be completely overhauled and serviced before delivery. A second station with an additional, identical rotary-tilt table is possible.

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2015, 01 Kdodpfeynlu Uex Ac Her

Kondisi: bekas, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Max. rolling force: 24 tons Max. tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Max. holding/tool length: 180 mm Max. workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Power supply: 400 Volt, 50 Hz, 10 kW - Swiveling roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox - Hydraulic system integrated in machine base - Operating manual with electrical schematic Space required (L x W x H): 2000 x 1450 x 190 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling dies with the same pitch as the workpiece form the thread by penetrating into the workpiece up to the nominal diameter. The maximum thread length corresponds to the width of the rolling dies. Kdodpfx Acsuz If Ne Hsr Through-feed Rolling: Used when the thread length is greater than the die width. Through-feed dies have three sections - the lead-in, the calibration zone, and the lead-out. Groove rolls have no pitch and are swiveled according to the thread pitch angle to be rolled. Pitch rolls differ from groove rolls by having a pitch in the profile. The sum of the pitch angle and the swivel angle gives the pitch angle in the workpiece.

Tahun pembuatan: 2023, Kondisi: baru, nomor mesin/kendaraan: PRJ065955, ALZMETALL bench drilling machine, drilling capacity in steel: 12mm Chuck mount: B16 external taper, spindle stroke: 40mm, throat: 200mm, column diameter: 50mm, machine table usable area: 300x240mm, with T-slots 2 x 12mm x 80mm, distance spindle-base plate min./max.: 110/250mm, manual feed, machine height without options: 670mm, net weight: 64 kg. - Infinitely variable speed 250-5000 rpm Kodpfxolub Rdo Ac Hsdr Standard equipment: 5" TFT LCD display with touch function: manual entry of target spindle speed, actual speed indication, integrated drilling depth display with touch zero point setting, virtual drilling depth scale on display, machine status displays and warnings on display, service information, selectable operating languages DE/EN/FR/ES/IT/NL/RU Single-phase motor 230 volt, 50 Hz, power plug pre-installed, cable length 2m, three separate buttons for clockwise - counterclockwise - stop, Spindle hold with brake function, spindle guard with electrical interlock, lockable main switch, mushroom emergency stop button (latching), infinitely variable speed adjustment via potentiometer, protection class IP54, spindle guard with electrical interlock, coating: DD textured paint signal white RAL 9003, PANTONE 7545c, black Includes the following options: LED machine lamp, position 12. Delivery time: Ex stock Waiblingen Beinstein

Tahun pembuatan: 2019, Kondisi: siap digunakan (bekas), jumlah sumbu: 2, This Nikon V-12BDC was manufactured in 2019. It features a 305 mm screen diameter, a measuring stage of 250 × 150 mm, and integrated digital XY and angle readouts for precise measurements. The device is equipped with a 3-position objective turret for rapid magnification changes and high-quality halogen illumination for clear images. Ideal for production control and precision engineering. Please contact us for further information about this machine. • Laterally correct image (no mirror inversion) for straightforward evaluation • 3-position objective turret for quick magnification selection • Magnifications: 10×, 20×, 50×, 100× • Screen diameter: 305 mm • Measuring stage travel: 250 × 150 mm (8" × 6"); rotary table type 2 • Maximum workpiece height: 100 mm • Integrated XY and angle digital display for accurate readings • Illumination: combination of contour (transmitted light) and vertical light (incident light) • Light source: 24 V / 150 W halogen for high-quality projection • 4-position condenser in transmitted light with automatic brightness adjustment according to magnification Kdodpfxox D I Eto Ac Hjr • Optics: semi-transparent mirror for clear incident light imaging; telecentric lenses for distortion-free imaging across the entire field • Focusing via movable optical head (table remains stable to avoid measurement deviations) • Measurement accuracy: contour illumination ±0.1%; inclination/surface illumination ±0.15% • Solid construction with precision-engineered guides; suitable for workshop use and easy to operate • Proven Nikon quality, made in Japan • Large projection area, suitable for medium-sized and complex workpieces • Fast magnification change via turret • Ideal for production inspection, toolmaking, precision mechanics, and sample testing • Upgradeable with digital interfaces or SPC connectivity

Kondisi: bekas, Tahun pembuatan: 2010, Grinding diameter: 350 mm Grinding length: 1000 mm Centre height: 175 mm Control: Fanuc 310is Completely mechanically overhauled. Including grinding process and setup for one workpiece. Original photo of the machine from EMO 2010. CNC control: GE Fanuc 310is Hand panel for CNC control GE Fanuc With Wenger loader Rotary part with automatic 1° indexing Grinding head UR 1-2-3 Grinding wheel assembly left: 500 x 80 mm Grinding wheel assembly right: 400 x 63 mm Operating unit for a high-frequency internal grinding spindle MFV / MFZ High-frequency internal grinding spindle MFN 1090 Coolant supply through the workpiece spindle Dressing device on the upper table Swivelling holder for PCBN diamond plates Base module for KEL-TOUCH contact sensor and KEL-BALANCE balancing devices KEL-TOUCH contact sensor for universal grinding head variants R / RS / UR / URS KEL-TOUCH on the workpiece spindle for internal and external grinding Provisions for measurement controls Movomatic ESZ 400 or Marposs P7 ME Kdedpfxsvdk N Ej Ac Hor Preparation for external filter Coolant shut-off for table units Fully enclosed for emulsion Mist extraction unit for emulsion Maintenance unit for pneumatic auxiliary functions Preparation for KEL-VITA gantry loader KEL-POS, MOVOMATIC: Measuring probe C25 Hydraulic preparation for arbour steady rest

Kondisi: baik (bekas), Tahun pembuatan: 2005, Machine type: Cylindrical grinding machine Manufacturer: Junker Model: Jumat 5340/s Serial number: 2328 Year of manufacture: 2005 Kedpfx Aekyrqijc Hedr Available immediately Ex works for self-dismantling Dismantling and loading can be offered as an option

Kondisi: bekas, Tahun pembuatan: 1991, Workpiece diameter 30 mm Thread length 110 mm Thread pitch 0.5-2.75 mm/rev Total power requirement 4.5 kW Machine weight approx. 1.7 t Space requirement approx. m M O N N I E R & ZAHNER Switzerland Thread whirling machine with workpiece loading system Type MZ 600, year of manufacture approx. 1991, #3591 Kdedpfxjt Hwzcs Ac Hsr _____ Max. workpiece diameter approx. 30 mm Max. workpiece length approx. 110 mm Axial milling length approx. 100 mm Module in steel approx. 1 Worm starts 1 Axis distance tool-workpiece min./max. 0 - 70 mm Whirling head swiveling +/- 12° Tool size approx. 70 x 16 mm Whirling head speeds approx. 1,000 - 6,000 rpm Pitch range approx. 0.5 - 2.75 mm/rev Whirling head drive approx. 1.5 kW Total drive approx. 4.5 kW - 220 V/380 V / 50 Hz Weight approx. 1,700 kg Accessories / Special Equipment: Machine is used for the production of medical screws and is equipped with an automatic workpiece feeder via a vibratory bowl feeder from Rübenach with pneumatic swing gripper for inserting the blanks, as well as a tailstock (pusher) and with ejector in the workpiece spindle head. Pneumatic workpiece clamping device in the workpiece spindle head. The finished parts are ejected and fall into a collection container. The tool slide is designed as a longitudinal and cross slide; the longitudinal slide determines the thread length and pitch via the leadscrew while the cross slide sets the thread depth. Copying unit at the end of the cross slide with template holder for tapered screws. Pitch gearbox in the workpiece spindle stock via change gears. Simple electrical program control with display of movement sequence. Error display, workpiece counter, oil mist extraction, coolant system, etc.

Kondisi: diremajakan ulang (bekas), Tahun pembuatan: 2015, Fungsionalitas: berfungsi sepenuhnya, jarak pergerakan sumbu X: 350 mm, jarak lintasan sumbu Y: 250 mm, jarak gerak sumbu Z: 300 mm, berat benda kerja (maks.): 500 kg, tinggi total: 2.398 mm, lebar total: 1.690 mm, panjang total: 1.900 mm, gores kuas bulu: 300 mm, panjang benda kerja (maks.): 790 mm, lebar benda kerja (maks.): 530 mm, tinggi benda kerja (maks.): 275 mm, berat keseluruhan: 2.800 kg, kapasitas tangki: 410 l, GF Machining Solutions FORM 200 Year of manufacture: 2015 – Only 7,200 eroding hours! Die-sinking EDM machine in C-frame design Fixed table with lowering tank Travel (X/Y/Z): 350 x 250 x 300 mm Maximum workpiece dimensions: 790 x 530 x 275 mm Maximum workpiece weight: 500 kg Programmable bath height: 100–325 mm Including pneumatic chuck Erowa ITS 50 / 3R Systems / Hirschmann (choice of system) Max. electrode weight: 50 kg Max. moment of inertia: 2,000 kgcm² 4-position electrode changer Kdodpfx Acowi Iuus Hor Control interface: AC FORM HMI Operation via 15" LCD color touchscreen Keyboard and hand control unit also available Machine dimensions: 1,900 x 1,690 x 2,398 mm Total weight: 2,800 kg The machine will be cleaned and serviced by us after order placement. Subsequently, an erosion test will be performed. We are happy to commission the machine at your site and provide operator training. Optional: - Transport - Cooling unit - Dielectric fluid - Clamping devices

Kondisi: bekas, Tahun pembuatan: 2004, Fungsionalitas: berfungsi sepenuhnya, Well-maintained Sunnen honing machine with Felsomat loading system. Internal diameter range: Krossgrinding® tools: 5.46 to 32 mm with CGT tools TurboHone® tools: 3.81 to 32 mm with MMT tools Connecting rod tools: 53.8 to 63.8 mm with CRT tools Larger tools: 25.4 to 101.6 mm Workpiece diameter: 8 to 150 mm Max. workpiece weight: 2.0 kg Spindle speed range: 250 to 3,700 rpm, adjustable Standard speed: High torque in the low-speed range: 20 to 1,000 rpm, adjustable Stroke speed range: 33 to 500 strokes/min, adjustable Coolant system Pump motor: 0.18 kW Coolant pump: 5.6 l/min Coolant tank capacity: 132 l and 11.2 l/min Coolant requirements: Compressed air requirements: 566 l/min at 4.48 bar, recommended 5.52 bar Temperature range: 0° to 35°C Floor requirements: (concrete floor) At least 150 mm thick Machine dimensions: L 2946 mm x W 2971 mm x H 1829 mm Kjdpfx Acoud Nm Rs Hsdr Colour: Pearl grey with pewter grey and burgundy decorative stripes Net weight: 1,579 kg Noise emission: < 71 dB (A) continuous load, < 75 dB (A) peak load Key features: Automatic setup: spindle speed, stroke speed, stroke length, feed rate and sparkout Automatic final machining: standard Machine operating modes: Automatic: Manual: Series production Single-piece production Clamping: optional