Kompresor sekrup

Alup Allegro 11

Tahun pembuatan: 1997, Kondisi: baik (bekas),

Kondisi: baik (bekas), Tahun pembuatan: 2004, nomor mesin/kendaraan: A II 151768, 25979 Gsdpfxjwrcq Nj Adtjbg - Operating hours: 16,550 h - Operating pressure: 10 bar - Flow rate: 15.9 l/s - Drive: 400 V / 7.5 kW - Motor speed: 3,000 rpm - Air receiver: 250 L - Space requirement: approx. W 700 x H 1,830 x D 1,050 mm - Weight: approx. 250 kg

Kondisi: siap digunakan (bekas), Max. operating overpressure: 11 bar, motor speed: 2,945 rpm, rated power: 30 kW, operating hours: 67,212 h. Gbedpfx Ajl Eyq Rodtog

Kondisi: sangat baik (bekas), Fungsionalitas: berfungsi sepenuhnya, berat keseluruhan: 1.830 kg, Tahun pembuatan: 2011, Air Compressor Brand: Atlas Copco Model: GA75VSD FF Year of manufacture: 2011 Maximum Allowable Working Pressure (MAWP): 12.8 bar / 185 psi / 1.28 MPa Capacity: 14.68 m³/min Voltage: 400 V Frequency: 50 Hz Motor power: 75 kW / 100 HP Rotational speed: 2975 rpm Gbodpfx Asv Nw A Ajdtsg Weight: 1830 kg Dimensions: 2300 x 1100 x 2000 mm Atlas Copco Air Dryer Type: ID 245 Year of manufacture: 2011 Voltage: 380/400 V, 50 Hz Power: 1.93 kW Weight: 150 kg Maximum air pressure: 13 bar Refrigerant: R410A Maximum refrigerant pressure: 42 bar Refrigerant temperature range: 1°C to 61°C Minimum refrigerant pressure: 1.2 bar

Kondisi: baik (bekas), Tahun pembuatan: 2010, jam operasional: 100.000 h, tekanan (min.): 10 batang, tekanan (maks.): 10 batang, jenis pendinginan: air, Perlengkapan: Pelat tipe tersedia, dokumentasi / manual, pengering pendingin, Atlas Copco Screw Compressor GA 18 - 10 FF Fully automatic, internally completely piped and wired compact unit, single-stage oil-injected compression, air-cooled, soundproofed, with integrated refrigeration dryer (WorkPlace Air System™). Technical Data Reference Conditions: Inlet pressure 1 bar Inlet temperature 20 °C Relative humidity 0% Usable volume flow at the outlet of the compact unit Gbjdpsu Rptyefx Adtsg at operating overpressure 9.75 bar: 49.4 l/s (2.96 m³/min) per ISO 1217-3, C Motor rated power 18 kW Motor rated speed 4,867 rpm Shaft power requirement at maximum operating pressure 24 kW Shaft power requirement at idle 5.6 kW Compressed air temperature after dryer 23 °C Cooling air flow 0.23 m³/s Oil filling quantity 12.2 l Residual oil content under reference conditions

Kondisi: baru, Pressure 25 t Throat depth 200 mm Stroke 4 - 80 mm Table size 520 x 400 mm Strokes 160 strokes/min Gedpfxeb U Hwno Adtobg Continuous working capacity 1370 Nm Single-stroke working capacity 2740 Nm Stroke adjustment 4 - 80 mm Ram adjustment 40 mm Ram surface 160 x 160 mm Table pass-through opening 200 x 150 mm Clamping plate 500 x 380 x 60 mm Table pass-through opening 80 mm Machine weight approx. 1.9 t - Ortlinghaus hydraulic clutch-brake combination - Vogel central lubrication - Balluff cam controller - Table height adjustable - Control cabinet with touchscreen - Foot switch

Kondisi: baru, Tahun pembuatan: 2024, Fungsionalitas: berfungsi sepenuhnya, berat keseluruhan: 3.450 kg, jenis bahan bakar: diesel, kapasitas tangki: 500 l, warna: putih, arus keluaran: 360 A, tegangan keluaran: 400 V, frekuensi keluaran: 50 Hz, jenis arus keluaran: tiga fasa, daya nominal: 270 kW (367,10 hp), daya kontinu: 250 kW (339,91 hp), panjang total: 3.650 mm, lebar total: 1.300 mm, tinggi total: 1.850 mm, kecepatan rotasi (maks.): 1.500 rpm, produsen motor: Ricardo, Cummins, jenis pendinginan: air, jenis arus masuk: tiga fasa, Three-phase stationary power generator Proton ZPP 250 (250kW - 270kW) in a compact, weatherproof, and additionally soundproof enclosure. The generator features an external ATS (Automatic Transfer Switch / Autostart) system, as well as many other functions detailed further in the description. • Model – Proton ZPP 250R ATS • Maximum power - 270 kW / 300 kVA • Rated power - 250 kW / 340 kVA • Ready for work - Yes (filled with fluids, test run performed) • Type – Industrial generator • Condition - Brand new • Manufacturer - Proton • Generator type - Three-phase • VAT invoice 23% • Year of manufacture - 2024 • Warranty - 36 months ⊳ ENGINE: Engine model - 6D10D315A-Turbo (British Series) Fuel type - Diesel Consumption: - 47.0 liters per hour (at 75% max power) - 34.0 liters per hour (at 50% max power) Engine configuration - Inline (R4) Displacement - 9700 cc3 Direct injection Lubrication system - Forced, engine with oil pump ⊳ ALTERNATOR: 100% copper windings AVR voltage regulator - Yes Alternator model - Proton 444D Rated power 400V - 250,000 Watts (250kW / 300kVA) Maximum power 400V (up to 15 minutes) - 270,000 Watts (270kW / 2340kVA) Rated power 230V - 83,000 Watts Maximum power 230V (up to 15 minutes) - 90,000 Watts Rated current (400V) - 360.0 A Current protection devices - C16, C32, main - 400A Frequency - 50 Hz Alternator construction - Synchronous ⊳ ENCLOSURE: Sound-attenuated enclosure Weatherproof enclosure Three-phase and single-phase sockets Fuel tank capacity - 500 liters Operating time on full tank (average) - 20 hours Transport set - Forklift pockets and HDS lifting eyes Dimensions 130 x 365 x 185 cm Gross weight - 3450 kg ⊳ FEATURES: Voltage regulator (AVR) - Stamford SX460 (2%) - electronic voltage stabilization under varying load - electronic frequency stabilization Automatic generator operation via ATS (Automatic Transfer Switch) Overload and thermal protection Oil pressure, oil level, and coolant level sensors Glow plugs Oil sump heater Coolant heater Battery - 2 x 140Ah Gsdpfx Astp Tfwodtobg Automatic battery charger ⊳ CONTROLLER: Controller model - Comap InteliLite 4 AMF 20 Hour meter Ammeter Voltmeter Built-in PLC logic and PLC editor Overload protection CAN module extensions SCADA system integration Additional outputs - 4G, Ethernet, RS232/485 connectivity Remote monitoring and control via GPRS (optional) Modbus, Ethernet communication (optional) Why choose us? We are a company specializing exclusively in power generators, operating in this sector for over 17 years and constantly striving to offer top-quality and highly reliable products. During this time, we have delivered solutions to over 10,000 clients across Poland, including its most remote regions. We meticulously select component suppliers, ensuring they are leaders in their respective industries. We offer a wide range of generators from 6 to 300kW with various engines, including English Ricardo, American Cummins, or German Deutz, as well as a variety of configurations tailored to customer requirements.

Kondisi: baik (bekas), daya: 30 kW (40,79 hp), Tahun pembuatan: 2010, jam operasional: 51.548 h, suhu lingkungan (min.): 3 °C, suhu lingkungan (maks.): 45 °C, tekanan (maks.): 8 batang, kecepatan rotasi (maks.): 2.945 rpm, nomor mesin/kendaraan: 100609.1, Perlengkapan: Pelat tipe tersedia, The Kaeser ASD 57 is an energy-efficient screw compressor designed to provide reliable compressed air supply for industrial applications. It features a compact design and quiet operation. Equipped with advanced Sigma Profile technology and intelligent control, it ensures optimal performance and durability. Technical details: Item number: 100609.1 Godpfxot Iwyue Adtsbg Serial number: 1941 Year of manufacture: 2010 Rated power: approx. 30 kW Maximum operating overpressure: 8 bar Motor speed: 2,945 rpm Condition: Used (see images and nameplate)

Kondisi: siap digunakan (bekas), An inspection is possible. Gbodsn D Hbnjpfx Adtjg

Kondisi: baru, diameter ulir metrik (min.): 3 mm, diameter ulir metrik (maks.): 16 mm, berat keseluruhan: 500 kg, panjang pemakanan sumbu X: 3.000 mm, panjang umpan sumbu Y: 1.500 mm, panjang umpan sumbu Z: 200 mm, torsi: 24 Nm, kecepatan spindel (maks.): 3.000 rpm, kecepatan spindel (min.): 50 rpm, daya: 0,005 kW (0,01 hp), The CMA three-axis controlled thread tapping center is specifically designed for the post-processing of laser-cut sheet metal parts, as well as complete machining of, for example, small components and tubes. The machine offers the following machining capabilities: - Thread tapping Gsdpfxjrbz T No Adtjbg - Drilling (standard / with chip break / tube cycle) - Countersinking - Flow drilling (with optimized feed curve) - Reaming - Simple graphical programming - Import of 2D DXF or DWG files - Machine table according to System 28 (similar to those by Demmeler and Siegmund welding tables) - Radial tool compensation with patented tool holder (accessory) - Tool probe for length measurement and as a breakage detector - Intuitive safety system using light barriers Standard configuration: Automatic tool changer with 10 positions, mounted on the gantry of the machine