1999 CM System D8 Pengangkut udara (rantai pengecatan) untuk penanganan kursi atau benda lain

CM System D8

Kondisi: bekas, Tahun pembuatan: 1999, 1999 CM System D8 Konveyor udara (rantai pengecatan) untuk pemindahan kursi atau produk sejenis, dicat pada gantungan. Panjang linier 600 meter. Instalasi lengkap dengan 2 cup cakram berputar, panel listrik, gantungan, perlengkapan lainnya seperti pada foto. Grup penggerak: 2 unit motorized Caterpillar tipe medium Kecepatan kerja: min/maks 0,9 m/menit Daya motor: 2 HP + 2 HP Perkembangan rantai D8 dan rol d. 37: 600 m Rel lurus sesuai ukuran: 531 m Lengkungan horizontal 90° r=500 mm: 91 unit Lengkungan horizontal 30° r=500: 6 unit Lengkungan vertikal 30° r=500: 26 unit Kjdpfx Asxywniefislr Jarak antar gantungan: 0,80 m

Kondisi: baru, The perfect coating for long-lasting protection. Powder coating is a highly effective and widely used method for applying a protective and decorative finish to various types of surfaces. It is a dry finishing process in which a fine powder consisting of resins, pigments, and additives is applied to a substrate. The powder is electrostatically charged, allowing it to adhere evenly to the surface and form a uniform coating. To achieve optimum adhesion and durability, the substrate is thoroughly cleaned and prepared beforehand. Oils, dirt, and other contaminants are removed to ensure a clean surface. This is essential for the powder to bond effectively with the substrate and to achieve a robust, long-lasting finish. Components of a Powder Coating System A powder coating plant typically consists of various components and equipment required for the application and curing of powder coatings. Spray Booth and Application Area The booth provides a clean environment for the application process and ensures even distribution of the powder. Powder Coating Gun A powder coating gun is used to apply the powder coating material to the workpiece. Ksdpoun Sd Uefx Afiolr Powder Feed System The powder feed system consists of a hopper or container where the powder coating material is stored. It usually includes devices such as powder pumps, feed hoses, and powder sieves to convey the powder from storage to the spray gun. Pretreatment Equipment Pretreatment equipment is used to prepare the substrate before powder coating application. This includes processes such as cleaning, degreasing, rinsing, and surface treatment to ensure optimum adhesion and coating durability. Curing Oven A curing oven is an essential part of a powder coating system. It is used to heat the coated substrate to the proper temperature, allowing the powder coating to melt, flow, and harden into a durable surface. The oven typically features a conveyor system or racks to transport coated parts through the oven chamber. Extraction System An extraction system is installed in the facility to remove excess powder, fumes, or volatile compounds generated during the coating process. It helps maintain a clean and safe working environment for personnel and prevents powder particle accumulation in the air. Looking for a powder coating solution? Are you searching for a tailored powder coating system? We specialize in delivering custom powder coating solutions tailored to your specific requirements. Whether you have particular color specifications, intricate designs, or challenging substrates, our experienced team is ready to deliver exceptional results. Contact us today to discuss your requirements and let us design a bespoke powder coating solution for you. Get in touch with us today!

Kondisi: baru, Tahun pembuatan: 2025, Fungsionalitas: berfungsi sepenuhnya, panjang total: 30.000 mm, tinggi total: 4.300 mm, lebar total: 6.500 mm, berat benda kerja (maks.): 100 kg, suhu: 220 °C, kapasitas pemanasan: 80 kW (108,77 hp), tinggi benda kerja (maks.): 1.200 mm, panjang benda kerja (maks.): 2.500 mm, bahan isolasi: Mineralwolle 75 kg/m³, ketebalan isolasi: 150 mm, lebar benda kerja (maks.): 800 mm, The continuous system consists of the following components: - Chemical pre-treatment by spraying - Dryer Klsdoum Ufljpfx Afijr - Powder coating system - Powder curing oven - Conveyor technology (indexed operation) - Electrical control system

Tahun pembuatan: 2011, Kondisi: siap digunakan (bekas), A complete paint shop system is available. Components: (1) Overhead conveyor, (2) Spray area/brush wall, length: 4000 mm, width: 1500 mm, height: 4800 mm, equipped with Maxon burner, exhaust duct, drawers for dry paint residue disposal, six filter mats, various filters, (3) Flash-off area, (4) Drying cabin, length: 6500 mm, width: 5200 mm, height: 3150 mm, equipped with Weishaupt WG10N/1-D ZM-LN gas burner. Overall system dimensions: 24,000 mm / 10,000 mm, max. power: 45 kW. Documentation is available. Kedpfx Aeup Ehisfiolr

Kondisi: bekas, Tahun pembuatan: 2010, 2010 powder coating line, excellent condition. Currently in operation, available for inspection and testing. Maximum part size: L x W x H = 2600 x 400 x 1850 mm Equipment Process conveyor Automatic speed V = 1.2 m/min Variable speed from 0.5 to 2.5 m/min Pretreatment station MNA-3-LPG, total length 16.7 m Entry zone: L = 2.5 m a. Washing, degreasing, and phosphating: L = 3.6 m Number of spraying frames – 10 Number of nozzles per frame – 18 Total number of nozzles – 180 Pump capacity – 162 m³/h Pump power – 15 kW 4 m³ tank for active liquid Internal heat exchanger with LPG burner – 160 kW Temperature – 50°C Mechanical oil separator Filtration system Dosing system with diaphragm pump and regulator Washing time – 3 min b. Drip-off zone L = 3.1 m Drip-off time – 2 min 30 sec c. First rinse L = 1.2 m Number of spraying frames – 4 Number of nozzles per frame – 18 Total number of nozzles – 64 Pump capacity – 38 m³/h Pump power – 3 kW 1.5 m³ water tank Rinsing time – 1 min d. Drip-off zone L = 3.1 m Drip-off time – 2 min 30 sec e. Final rinse L = 1.28 m Number of spraying frames – 3 Number of nozzles per frame – 18 Total number of nozzles – 54 Pump capacity – 33 m³/h 1.5 m³ water tank Pump power – 3 kW Additional spray frame Rinse time – 1 min f. Drip-off zone L = 2 m Drip-off time – 1 min 40 sec Three extraction system connections with three fans Working zone made of stainless steel Pipes made of PVC or stainless steel 1 unit. Automatic post-wash dryer AST-1-KLPG: Working area dimensions L x W x H = 7000 x 3000 x 2800 mm Air curtains on each side to reduce heat loss Indirect heat exchanger, LPG-fired, 200 kW Three fans, air supply 6000 m³/h Two extraction system connections Temperature sensor and controller Overheat sensor Circulation detector Working zone made of galvanized steel Thermal insulation 200 mm thick Drying time – 10 min 1 unit. Automatic curing oven APT-2-KLPG Working area dimensions L x W x H = 10200 x 3600 x 2800 mm Air curtains on one side to reduce heat loss Two indirect heat exchangers, LPG-fired, 300 kW each Eight circulation fans, each with a capacity of 6000 m³/h Two extraction system connections Temperature sensor and controller Klodpfx Aov Ed Uksfisr Overheat sensor Circulation detector Working zone made of galvanized steel Thermal insulation 200 mm thick Curing time – 25 min 1 unit. Overhead rail conveyor system ATR for paint shop: Straight rail with hangers L = 400 mm – 146 m Drive station – 2 units Tensioning station – 1 unit Chain lubrication station – 1 unit Rails supporting structure drawings – 1 set.

Kondisi: bekas, es_en_001 Kodpfx Aoxgnpkjfislr

Kondisi: baru, Tahun pembuatan: 2025, GARIS COATING POWDER HORIZONTAL UNTUK PROFIL ALUMINIUM Kami menambah nilai pada produksi Anda. * Kecepatan konveyor disesuaikan dengan kapasitas harian Anda Kljdpfx Aovv Nh Rsfier Konveyor udara – tipe monorel atau power & free Booth pengecatan powder otomatis, struktur antistatik logam atau PVC Peralatan pengecatan powder otomatis dengan sistem reciprocating Oven polimerisasi tipe terowongan – pemanas gas, diesel, atau listrik Dibuat di Türkiye Tanda CE Kami menawarkan solusi teknis terbaik dan harga kompetitif * Kantor di Prancis dan Jerman, Hubungi kami untuk informasi lebih lanjut dan penawaran harga

Kondisi: sangat baik (bekas), Tahun pembuatan: 2018, Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: Inv.119140, panjang total: 26.000 mm, lebar total: 9.000 mm, Perlengkapan: kabin, pencahayaan, 1 used painting line, including circulating conveyor belt, manual spray booth for sample processing, automatic spray booth with robot and workpiece rotary holder, reverse osmosis system for DI-water, paint preparation station, and exhaust air treatment unit. The plant is operated in two-shift serial production. Manual loading and unloading onto the conveyor belt; otherwise fully automatic operation. 18.7.25: Update: Dismantling from September 2025 at the Lohr plant to be carried out by the buyer. Buyer bears all costs for dismantling, packaging, collection, and transport to their own facility (FCA). The facility area must be cleared by mid-January 2026 at the latest to allow for installation of new production machinery. For further information, please refer to the attached handout/flyer. Due to the high effort involved in dismantling, early and thorough planning with the dismantling contractor is required, as well as prompt contact or a site visit to the plant. More information can be found in the attached handout. ----- Please submit your offer price. Sale only within the EU, Switzerland, Turkey, and United Kingdom. Dismantling should be carried out by the buyer. Kjdpjwqg Iiefx Afijlr No packaging provided. Any warranty rights are excluded. If you wish to carry out the dismantling yourself, please state this in your offer. We do not guarantee the accuracy of technical data, the completeness of accessories or tools, or compliance with occupational safety and environmental protection requirements set forth in accident prevention regulations.

Kondisi: sangat baik (bekas), Tahun pembuatan: 2015, Fungsionalitas: berfungsi sepenuhnya, panjang total: 43.000 mm, tinggi total: 3.800 mm, lebar total: 20.000 mm, jenis arus masuk: tiga fasa, berat benda kerja (maks.): 200 kg, sambungan udara terkompresi: 9 batang, tinggi benda kerja (maks.): 2.400 mm, panjang benda kerja (maks.): 7.200 mm, We are offering this BEWAP MACRO 6 POWDER COATING MACHINE. Complete 7.2m Powder Coating Line, year of manufacture 2015, in very good condition. Full set for surface treatment, including 2 powder coating booths and 2 curing ovens for powder coating applications. The equipment is in perfect working order. Year 2015. Surface treatment cabin (constructed in 316L stainless steel, membrane spray pumps, dosing pumps, stainless steel pickling tanks with immersion heaters, rinsing tanks, effluent tank, ED tank, dosing pumps, reverse osmosis unit, water softener) Drying oven (gas burner, control cabinet) 2 manual powder coating booths with automatic feed and extraction Curing oven (gas burner, control cabinet) Frame with manual overhead conveyor: 3 transfer trolleys with 3 lifting beams each (200 kg per beam) 2 lifting stations for loading and unloading 36 lifting beams in total Simultaneous processing with 3 lifting beams Compatible with Qualicoat and Qualilaquage standards Maximum part dimensions per beam: Maximum length: 7200 mm Klodpfx Ajyc S Htjfisr Maximum height: 2400 mm Maximum width: 500 mm (width configuration up to 1000 mm possible) To be dismantled and removed on site Price: €150,000 (excluding VAT) If you have any questions or require further information, please feel free to send us a message or call us. Viewing possible.

Kondisi: baru, Tahun pembuatan: 2025, Fungsionalitas: berfungsi sepenuhnya, fr_FR Kodsvv H Uuopfx Afielr