PERGANTIAN ALAT MOTOR

HOMAG

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2008, nomor mesin/kendaraan: 0-250-23-0021, Fungsionalitas: berfungsi sepenuhnya, panjang benda kerja (maks.): 2.500 mm, lebar benda kerja (maks.): 1.000 mm, tinggi benda kerja (maks.): 80 mm, kecepatan pemakanan sumbu X: 138 m/menit, laju pemakanan gandar Y: 80 m/menit, Penawaran mengikat untuk pengambilan tepat waktu paling lambat sampai 15.06.2026! DETAIL TEKNIS Kecepatan Sumbu-X: 138 m/menit Kecepatan Sumbu-Y: 80 m/menit Kecepatan Sumbu-Z: 50 m/menit Panjang benda kerja: 300–2.500 mm Lebar benda kerja: 100–1.000 mm Tinggi benda kerja: 4–80 mm DETAIL MESIN Kontrol: power control PC 85 T Dimensi (P x L x T): 6.500 × 2.300 × 2.700 mm Listrik: 3 × 415 V / 50 Hz Daya terpasang: 19,5 kW Sekering: 50 A Pneumatik: min. 7 bar Konsumsi udara: 2.500 NL/menit Koneksi ekstraksi: 2 × 280 mm Kapasitas ekstraksi: min. 4.450 m³/jam Gedoy Sad Hjpfx Aiyjub

Kondisi: bekas, Tahun pembuatan: 2007, daya: 43 kW (58,46 hp), ketinggian potong (maks.): 90 mm, lebar pemotongan (maks.): 1.200 mm, panjang pemotongan (maks.): 5.600 mm, kecepatan pemakanan sumbu X: 40 m/menit, This machine comes from a company closure. Inspections under power are possible! Gedpfxey R S I Ue Aiyeub TECHNICAL DETAILS Max. panel width: 1,200 mm Max. panel length: 5,600 mm Min. panel width: 150 mm Min. panel length: 250 mm Min. panel thickness: 8 mm Max. panel thickness: 90 mm Maximum feed speed: 40 m/min The machine is equipped with the following configuration: Number of machining units: 4 Unit 1: Double trimmer, top and bottom Motor power: 11 kW Spindle speed: 7,090 rpm Unit 2: Scoring unit Motor power: 2.2 kW Spindle speed: 6,920 rpm Unit 3: Milling unit Motor power: 8 kW Spindle speed: 7,090 rpm Unit 4: Milling unit Design: located on rear table Motor power: 2.2 kW Spindle speed: 6,920 rpm MACHINE DETAILS Control system: WINDOWS Machine programming software: POWER CONTROL PC22 Total connected load: 43 kW EQUIPMENT Upper pressure unit Additional guide for workpieces Rubber conveyor belts NC positioning The machine is sold and delivered in its actual and legal condition (“as seen and liked”) based on photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8448

Kondisi: bekas, Tahun pembuatan: 2007, jarak pergerakan sumbu X: 6.000 mm, jarak lintasan sumbu Y: 3.000 mm, jumlah slot dalam magazin alat: 10, model controller: POWER CONTROL PC85, kecepatan spindel (maks.): 24.000 rpm, The machine comes from a business liquidation. Viewings under power are possible! TECHNICAL DETAILS Travel range X-axis: 6,000 mm Travel range Y-axis: 3,000 mm Working area X-axis: 5,600 mm Working area Y-axis: 1,200 mm Traverse speed X-axis: 80 m/min Traverse speed Y-axis: 80 m/min Traverse speed Z-axis: 30 m/min Milling spindles: 2 Main electrospindle power: 11 kW Spindle speed: 24,000 rpm Total number of tool changer positions: 10 MACHINE DETAILS Type of machining: Milling Control system: POWER CONTROL PC85 Machine programming software: WOODWOP 5.0 Number of controlled axes: 4 Vacuum cups: 32 Guedpfx Aijy R Swijyob Single vacuum pump capacity: 120 + 80 m³/h Number of pumps: 2 Total installed power: 27 kW EQUIPMENT Vacuum loading Motorized transfer system Automatic panel loading system Automatic panel stacking system Liquid cooling system CE marking Protective structure for operating units with safety sensors Safety netting on the machine Waste chip conveyor The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 8457

Kondisi: bekas, Tahun pembuatan: 2002, jarak pergerakan sumbu X: 10.500 mm, jarak lintasan sumbu Y: 2.700 mm, jumlah slot dalam magazin alat: 24, model controller: POWER CONTROL PC83, kecepatan spindle milling (maks.): 18.000 rpm, The machine originates from a business closure. Inspections under power are possible! TECHNICAL DETAILS Travel range X-axis: 10,500 mm Travel range Y-axis: 2,700 mm Working area X-axis: 5,600 mm Working area Y-axis: 1,200 mm Traverse speed X-axis: 80 m/min Traverse speed Y-axis: 80 m/min Traverse speed Z-axis: 30 m/min Main electrospindle power: 12 kW Number of milling spindles: 2 Milling spindle motor power: 12 kW Milling spindle speed: 18,000 rpm Number of controlled axes: 4 Number of tools in changer: 24 Number of tool magazine positions: 12 (2 magazines) Maximum processable panel height: 40 mm Minimum processable panel height: 10 mm MACHINE DETAILS Type of machining: Edge processing, Milling Control system: POWER CONTROL PC83 Programming software: WOODWOP 5.0 Total installed power: 51 kW Number of work zones: 1 Number of rails: 5 Number of vacuum pods: 10 Number of vacuum pumps: 2 Capacity per pump: 120 m³/h EQUIPMENT Guodjy R Si Sopfx Aiysb Worktable: Pod and rail Positioning via NC Automatic panel loading system: Vacuum loading system Automatic panel stacking system Vacuum pump Liquid cooling system Adhesive unit with premelter for hot melt glue Edge band magazine Tool magazine at rear of the machine Protective structure for operating units with safety sensors Protective net attached to the machine Safety system: Front safety mats Waste chip conveyor The machine is sold and delivered in its actual and legal condition ("as seen and approved"), based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 8458

Kondisi: bekas, Tahun pembuatan: 2007, tinggi benda kerja (maks.): 60 mm, ketebalan tepi (maks.): 35 mm, kecepatan pemakanan sumbu X: 40 m/menit, model controller: POWER CONTROL PC22", The machine comes from a business liquidation. Inspections under power are possible! TECHNICAL DETAILS Number of working units: 11 Max. feed speed: 40 m/min Max. panel thickness: 60 mm Min. panel height: 16 mm Min. panel width: 85 mm Min. edge thickness: 0.3 mm Max. edge thickness: 35 mm Pressing system: rubber belt Workpiece support guides Positioning via NC Infeed alignment system for panels The machine is equipped with the following configuration: PRE-MILLING / MILLING UNITS Number of pre-milling / milling units: 2 Unit 1: Pre-milling unit Motor power: 4.5 kW Spindle speed: 5,860 rpm Automatic time-controlled engagement Unit 2: End trimming unit Motor power: 1.8 kW Automatic tool change GLUING AND EDGE FEEDING Number of edge rolls: 68 Number of pressure rollers: 14 (1 x 7 + 1 x 7) Lamps for pre-heating the panel edge Pre-melter for PUR glue Gluing system Glue pot for PUR glue Positioning via NC EDGE PROCESSING UNITS Number of edge processing units: 8 Unit 1: End trimming unit Number of motors: 2 Motor power: 0.22 kW Spindle speed: 10,350 rpm Positioning via NC Unit 2: Top and bottom flush trimming unit Number of motors: 2 Motor power: 0.55 kW Gusdjy R R T Nspfx Aiyob Spindle speed: 11,400 rpm Unit 3: Corner rounding unit Number of motors: 2 Motor power: 0.4 kW Spindle speed: 10,980 rpm Automatic tool change Positioning via NC Automatic time-controlled engagement Unit 4: Edge scraper unit Positioning via NC Unit 5: Glue joint scraper unit Unit 6: Buffing unit Number of motors: 4 Motor power: 0.25 kW Spindle speed: 1,390 rpm Automatic time-controlled engagement Unit 7: Buffing unit Number of motors: 1 Motor power: 0.30 kW Spindle speed: 3,000 rpm Unit 8: Buffing unit Number of motors: 2 Motor power: 0.18 kW Spindle speed: 1,370 rpm MACHINE DETAILS Control system: WINDOWS XP Machine programming software: POWER CONTROL PC22 The machine is sold and delivered in its actual and legal condition (“as seen and approved”) based on photographic documentation and technical/commercial descriptive documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at its destination. External reference: 8453

Kondisi: sangat baik (bekas), Tahun pembuatan: 2020, Fungsionalitas: berfungsi sepenuhnya, daya: 14 kW (19,03 hp), tegangan masuk: 400 V, frekuensi input: 50 Hz, Perlengkapan: dokumentasi / manual, DRILLTEQ V-200 (OPTIMAT BHX055) Gjdpsyvh Dpofx Aiyjub

Kondisi: bekas, Tahun pembuatan: 2002, Fungsionalitas: berfungsi sepenuhnya, Homag Profi Line CHF 51/32/32 Panel Saw - Tahun pembuatan: 2002 Gedpox Ey Nvjfx Aiyjub - Lebar pemotongan: 3200 x 3200 mm - 3 meja dengan tirai udara - Proyeksi mata gergaji: 102 mm - Tinggi potong: 85 mm - Mata utama: 400 mm - Motor utama: 11,2 kW (15 HP) - Pisau scoring dengan motor independen

Kondisi: sangat baik (bekas), Tahun pembuatan: 2021, Fungsionalitas: berfungsi sepenuhnya, used 5-axis CNC machining center Manufacturer: Homag Model: Centateq 110 (5-axis) Year of manufacture: 2021 Last manufacturer service: 18.05.2026 Console table with LED suction cup position indicator, Godoy Nzc Sjpfx Aiyoub 6 manually adjustable consoles (length 1360 mm) each with 3 vacuum cups, 4 support rails Workpiece clamping via vacuum pump 63 m³/h LED system for vacuum fixtures, X-axis working range: 3100 mm Y-axis working range: up to 1250 mm with front stop; up to 1405 mm at rear with 25 mm tool diameter Z-axis working range: 260 mm / 160 mm with standard suction cups Drilling head: 12 vertical spindles; 6 (4+2) horizontal drilling spindles, Grooving saw at 90°, tiltable, max. 125 mm dia. Main spindle: DRIVE Future 10 kW, liquid cooled, 1500 – 24,000 rpm 14-position tool changer (carousel) at rear and 10-position fixed linear tool changer at side Aggregate carrier for 2 Z-axes (main spindle + drilling unit) Chip conveyor, program-controlled extraction hood Power-Control PC 86 POWERTOUCH with Woodwop (incl. Lamello CLAMEX-P component), WoodWop also for AV workstation (Office Professional version; DXF-Import Basic) UPS for PC; Tapio Ready compatible Basic barcode reading system Documentation: German Pictured tools, HSK tool holders, drills, etc. are not included in the scope of delivery! Machine available from end of May 2026 The attached PDF file for the machine description refers to the machine’s original delivery status from the manufacturer in 2021 and is not binding for the current delivery status as a used machine.

Kondisi: bekas, nomor mesin/kendaraan: 008522, translation_001 Gujdpfx Aijy Nx U Ejysb

Kondisi: bekas, nomor mesin/kendaraan: 008323, Tipe tepi yang dipasang: tepi tipis, tepi tebal, kayu solid Guedpfx Aijx Hpkxsysb Sistem lem: EVA, PUR Penghalusan sambungan: ya Agregat multifungsi: ya Kecepatan maju maksimum: 20 m/menit Ketebalan papan maksimum: 60 mm Unit kerja: 7 unit