Trailer semi swap body

Abrollcontainer Container 6,5 m Kran Fassi F150

Brand new roll-off container with FASSI loading crane

ELLERMANN roll-off container according to DIN 30722-1
Standard container Type S 77 with crane platform
Internal dimensions: approx. 6.5/5.3 x 2.3 x 2.0 meters (all dimensions are approximate)
Usable volume: approx. 24 m³
Paint finish: RAL 7016 (anthracite gray)

? Mounting brackets for hook lift systems according to DIN 30722-1 (15,000 kg)
with rear outer rollers and subframe made of INP 180
Outer rollers are greaseable and replaceable
Mounting bracket Ø 50 mm, hook height 1,570 mm
Transition from the subframe to the end wall support is reinforced with 10 mm knee plates
? Crane platform 20 mm thick on the end face, length approx. 1,200 mm
Reinforcement on the end wall support and subframe on the inside
Additional stiffening on the end support
? Crane cutout on the end wall (according to Fassi drawings)
? Bottom pan made of 5 mm St 37.2 (S235JR)
? Side walls made of 3 mm St 37.2 (S235JR)
Bwsdezq Iu Uopfx Ad Rsr
? Rounded bottom pan, raised approx. 250 mm towards the side wall
? End profile made of sturdy round tube Ø 90 mm
? Spant spacing 750 mm
Spant profile U 80 x 50 mm
? On both sides, 1 x transverse spant in the middle, fully welded
? Double-wing door at the rear with Dutch door latch
and lateral safety central locking system according to UVV
Safety central locking system extended to 2,000 mm
Door latch with container door opening aid and hockey lock
Additional opening handle on the left door leaf
? All-around tarpaulin and net hooks
? Container primed once on the inside, primed twice on the outside
and painted twice in a single color on the outside
? UVV stickers with safety instructions
? Container inspected and approved according to DGUV Rule 214-017 (formerly BGR 186)
? Container inspection book (digitized) for documenting the
required annual recurring inspection according to UVV

FASSI loading crane F150A.2 e-dynamic

Design according to CE directive (EN 12999)
The equipment manufacturer must carry out the inspection
when the loading crane has been mounted in its final position
and is ready for operation.
Base unit: F150A.2 e-dynamic

Slewing range 416°
all hydraulic cylinders are double-acting
piston rods are hard-chrome plated
double knee joint system with PROLINK (over-extension of the knuckle arm up to 15°)
electronic overload shut-off device with FX500
6 functions RCH or RCS radio remote control (linear levers) with
display and XP system
emergency shut-off and optical alarm (90% and 100%)
including digital slewing limitation, adjustable
FASSI stability control FSC incl. LMB II
pressure relief and load holding valves, high-pressure filter
Danfoss S800 control block with 4 control valves, operable on one side
separate hydraulic tank (90 l) with filter, mounted on the crane base
extendable on both sides, support width 4.60 m, hydraulic support ? CE, incl. M.O.L.
Standard color RAL 3020 traffic red - all cylinders painted black
load hook and attachment brackets (short / 500 mm)
Transport position: folded across the direction of travel
Dead point above the support beam
Note: Observe on-board voltage / 12V or 24V, standard 24V

F150A.2.23 e-dynamic » Base unit
IE742 connection box
Support spread to support width 5.4 m
Move dead point
1 LED work spotlight on the knuckle arm » mounted
LED for 2 outriggers, not mounted » (crane)
Control system for 2 additional functions with » 2 hose lines / eactive
Slewing valve, only for cranes with rack and pinion
Quick-action valve for the outriggers
Additional cos

Iklan ini diterjemahkan secara otomatis. Kesalahan terjemahan mungkin terjadi.