Gergaji pita otomatis - horizontal

MEBA 280 A

Kondisi: baru, Tahun pembuatan: 2024, New machine Year of manufacture: 2024 Equipment and technical data: Right-hand version Technical data: Overall dimensions: 1,900 x 1,410 mm Hopper opening: 1,044 x 1,044 mm Hopper height: 1,010 mm Hopper volume: 1.1 m³ Drive power: 5.5 kW Briquette diameter: 50 mm Hydraulic oil: 160 l Throughput performance: up to 50 kg/h (depending on material) Paint finish: Weima standard Connected load: 400 V +/- 5% / 50 Hz Including: Press mechanism with filler cylinder, main cylinder, clamp cylinder Connector for transport pipe Chromed clamp Hydraulic tank 160 l with pump motor + valve control Safety switch for oil temperature Base plate 1,040 x 1,040 mm with agitator + motor and screw discharge chute + motor Side walls standard height 1,010 mm Base frame with rubber feet Control cabinet on hopper and electrical control Briquette length monitoring Automatic end position for all cylinders Manual control Automatic "On/Off" with level limit switch Material: planer shavings, sawdust from solid wood, loose, clean and free of foreign matter*/ Dimensions: max. 12 mm Throughput performance: approx. 50 m³/year/ * Foreign matter specification: Anything other than wood, wood pieces larger than 12 mm. Throughput is highly material-dependent. Listed figures are average values. Depending on mix ratio, moisture content, and material characteristics! Application case not or not fully known/specifed. Machine is sold appropriately and Nodpfxot Hagns Aahsdf solution-oriented by a specialist dealer. With heat buildup in the hopper, running time may be drastically reduced depending on heat development. Availability: promptly Location: Solingen

Kondisi: bekas, Tahun pembuatan: 2003, Steuerung 840D-PCU 50 V1 Tersedia: 3 unit Pendingin: ya Konveyor serpihan: ya Arus nominal generator: 110 A Ndodpfx Aoqn A Rrjahof Daya terpasang: 56 kW

Tahun pembuatan: 2002, Kondisi: hampir baru (bekas), nomor mesin/kendaraan: 16.34.02, 6-fach-6-Schlag-Kopierpresse MULTIPRESS MP610LS Maximaler Abscherdurchmesser (bei 500 N/mm²): 12 mm Maximale Abscherlänge: 105 mm Nodpjh Tkrajfx Aahedf Maximale Auswerferlänge (Matrizenseite): 80 mm Maximale PKO-Länge: 23 mm Maximale Geschwindigkeit: 180 Stück/min

Kondisi: baru, Cutting diameter round: 550 mm Cutting diameter square: 550 mm Cutting diameter flat: 550 x 550 mm Saw blade length: 5980 x 41 x 1.3 mm Table height: 800 mm Blade speed: 20 - 100 m/min Total power requirement: 5.5 kW Machine weight: approx. 3.8 t Dimensions (L x W x H): 3.0 x 2.15 x 2.2 m SPECIAL OFFER PRICE!!!! 2-Column High-Performance Bandsaw Machines of the SBS Series The SBS series impresses with its advanced technology, high quality, durability, and an unrivaled comprehensive standard equipment package. • Modern SNC 20 control system for CNC versions • Frequency-controlled saw drive • Control buttons with pictograms • Work light • Powered chip brush • Hydraulic blade tensioning • Clamping pressure regulation • Double vice (before and after the blade) • Inch mode for positioning • Bundle clamping electrically and hydraulically pre-installed Ndodpfx Aofg E Hwoahef • Chip conveyor The SNC 20 control system enables convenient and uncomplicated input of up to 20 different sawing jobs (length and quantity). Once the desired dimension is entered, the control system automatically calculates the kerf and the number of feed cycles. Additionally, the error code display system enables rapid fault analysis and troubleshooting.

Kondisi: perlu perbaikan (bekas), Machine number: 1464 Type / Model: FUW 250/IV Travel (X-Y-Z): 400 - 220 - 400 mm Table size: 630 x 350 mm Clamping surface: 700 x 300 mm Speed range: 45 to 2,240 rpm Spindle taper: SK 40 Feed range longitudinal: 6.3 to 1,250 mm/min Feed range cross: 6.3 to 1,250 mm/min Power connection: 7.4 kW Accessories/Equipment: Vertical head Condition: 2 controllers defective Note: Machine repair EUR 2,000 Weight: 1.45 t Dimensions: 1,500 x 1,600 x 1,800 mm Ndedpfx Asd Hl Steahsf

Kondisi: baru, Tahun pembuatan: 2025, Quick mitre adjustment from 30° to 150° steplessly with 0.5° accuracy according to scale. The mitre pivot point is the intersection between the saw blade and the material support, which means there is no change in length measurement. Stops at 30° and 45° on both left and right sides. Manual material clamping. At any frame angle, the material is clamped parallel at 90°. Cutting pressure reduction via the dead weight of the robust, torsion-resistant saw frame and fine adjustment based on material cross-section through hydraulic damping cylinder. Standard built-in coolant system, optionally upgradable with a micro-dosing unit. Machine stand with integrated chip collection tray. Saw blade drive with automatic shut-off. Precise saw blade carbide roller guide. Paint finish in silver-grey / blue-grey (RAL 7001 / RAL 7031). 1 saw blade mounted on the machine, 4/6 TPI. Operating manual and spare parts list supplied on CD-ROM. Optional equipment: Hydraulic lifting of the saw frame. Ndodjbi S Dijpfx Aahof Design: Manual Mitre Cutting Capacities: 30° left: Ø 130 mm; square 120x120 mm 45° left: Ø 200 mm; square 180x180 mm 90°: round Ø 260 mm; square 300x260 mm 45° right: Ø 200 mm; square 180x180 mm 30° right: Ø 130 mm; square 120x120 mm Motor: [kW] 1.8 Saw blade: [mm] 3350x27x0.9 Blade speed: 35/75 m/min Working height: [mm] 900

Kondisi: sangat baik (bekas), Double spindle, C-axis FANUC 18i-TB control Ndjdpfx Aaswufdqohef Turning diameter: up to 300 mm Turning length: up to 366 mm Main spindle speed: 30–5,000 rpm Counter spindle speed: 30–6,000 rpm Turret: 12 driven stations C-axis indexing: 0.001 degrees Various accessories MARCELS MASCHINEN CH

Kondisi: siap digunakan (bekas), fr Njdpfx Aasuciqaohjdf

Kondisi: baik (bekas),

Kondisi: sangat baik (bekas), Tahun pembuatan: 2014, panjang pembubutan: 1.233 mm, diameter pembubutan: 420 mm, MAZAK Model QT SMART 350 M U1250 Year: 2014 Mazatrol Smart Control Max. turning diameter: 420 mm Max. swing diameter: 720 mm Max. turning length: 1,233 mm Spindle motor: 30 kW Max. spindle speed: 3,300 rpm Full C-axis Max. bar capacity: 102 mm Spindle nose: A2-11 12-position turret 12 stations for driven tools Driven tools: 7.5 kW Max. speed of driven tools: 4,000 rpm Travel: X-axis: 265 mm Z-axis: 1,233 mm Tailstock: 1,265 mm High-pressure coolant, 15 bar Tooleye Mayfran chip conveyor, right-hand discharge Kitagawa B210 3-jaw chuck, diameter 254 mm Tailstock, MT5 Set of tool holders: 8 static holders + 2 driven tool holders Ndodpfx Aaorn Txkshsf Weight: 7,200 kg LxWxH: 3,770 x 1,910 x 1,900 mm