Turbin uap

Nouvo Pignone ENK 32/45

Kondisi: baru, Tahun pembuatan: 2024, Fungsionalitas: berfungsi sepenuhnya, tekanan: 16 batang, frekuensi input: 50 Hz, jenis arus masuk: tiga fasa, suhu: 400 °C, tegangan masuk: 6.000 V, kecepatan rotasi (min.): 1.500 rpm, kecepatan rotasi (maks.): 1.500 rpm, jenis pendinginan: udara, Industrial steam turbogenerator Howden – model KK&K TWIN CA46, NEW, never installed and never commissioned, still under manufacturer’s warranty. Following a revision of long-term industrial strategy, a Howden KK&K TWIN CA46 steam turbogenerator is available for sale, complete according to original OEM supply. The machine is NEW, entirely manufactured and tested at OEM level, but never installed or put into service. It is still covered by the manufacturer’s warranty and is stored in an indoor, climate-controlled environment. Immediate availability eliminates standard production lead times, which for this type of equipment are generally 24–36 months. Main supply: - Steam turbine on skid with integrated gearbox - Synchronous generator supplied separately Turbine technical configuration: - Model: KK&K TWIN CA46 - Dual-casing turbine (Steam Part A + Steam Part B) - Integrated 3-shaft gearbox (2 pinions + central wheel) - Controlled steam extraction between HP and LP section (included) Main design conditions: - Inlet steam pressure (HP): 16 bar(a) - Inlet steam temperature: 400 °C - Electrical power at terminals: up to 1,595 kW - Nominal speed: 1,500 rpm Electric generator: - Three-phase synchronous generator - Rated power: 1,994 kVA - Voltage: 6 kV – Frequency: 50 Hz - Cooling: IC31, air - Brushless execution, suitable for parallel operation with the grid Included systems: - Integrated oil system within the base frame - Main mechanical oil pump and auxiliary electric pump - Local panel on skid - Control and protection panel with Siemens SIPROTEC 5 system - Electronic speed and pressure governor - Independent overspeed protection device - Turbogenerator simulation model ENC-RfG Typical applications: - Industrial cogeneration (CHP) plants - Energy recovery from process steam - Biomass and waste-to-energy plants - Combined production of electricity and service steam Condition and status: - Condition: NEW - Year of manufacture: end of 2024 - Never installed – never commissioned - Still covered by manufacturer’s warranty - Complete OEM technical documentation available - Option of installation and commissioning with manufacturer’s support Possible application fields: - Biomass and waste-to-energy plants for the production of electricity and service steam, with immediate unit availability and without multi-year manufacturing lead times - Industrial cogeneration (CHP) in plants with continuous process steam demand (paper, food, chemical, manufacturing industries) - Revamping / repowering of existing plants as a rapid alternative to new OEM supply with 24–36 month lead times Price: on request. Further technical information and documentation available upon request. Hedpfjyidvdsx Aazonr

Kondisi: bekas, TECHNICAL SPECIFICATIONS - Number of axes: 10 Hodpev Ig Avsfx Aazenr - Number of spindles: 2 MAIN SPINDLE - Spindle drive power: 24 kW - Spindle speed: 5,000 rpm - Max. bar diameter: 65 mm - Min. C-axis resolution: 0.001° SUB SPINDLE - Spindle drive power: 24 kW - Spindle speed: 5,000 rpm - Max. bar diameter: 65 mm - Min. C-axis resolution: 0.001° - Travel: 390 / 600 mm TURNING-MILLING SPINDLE - X travel: 350 mm - Y travel: ±80 mm - B-axis stroke: 270° - Min. B-axis resolution: 0.001° - Tool type: HSK-T40 - Spindle speed: 18,000 rpm - Spindle drive power: 11 kW - Fixed tools on electrospindle for milling: 6 x VDI25 LOWER TURNING AND MILLING SPINDLE - Y travel: ±80 mm - B-axis stroke: 270° - Min. B-axis resolution: 0.001° - Tool type: HSK-T40 - Spindle speed: 18,000 rpm - Spindle drive power: 11 kW - Fixed tools on electrospindle for milling: 6 x VDI25 TOOL CHANGER - Tool changer type: Bras charger - Number of magazine tools: 80 - Tool change time: 4.5 sec ELECTRICAL SUPPLY - Supply voltage: 400 V - Total power: 68 kW WEIGHT AND DIMENSIONS - Machine height: 2,500 mm - Machine weight: 11,000 kg MACHINE HOURS - Spindle hours: 19,781 h - Turning-milling spindle hours: 9,713 h EQUIPMENT - Control: Siemens Sinumerik 840D SL - Coolant tank * with high-pressure pump * with paper filter * internal coolant supply (IKZ) - Chip conveyor - Spindle cooling - Parts removal

Kondisi: sangat baik (bekas), Motor-driven NC rotary table Infinitely variable rotary table (indexing 0.001°) Integrated pallet station: pallet changer table (2 pallets) Manufacturer: Rückle Model: PKTF 1200 Table size: 1200 mm x 1200 mm Total height: 660 mm Centering bore: 100 H6 mm Clamping slots: 7 units Slot size: 22 H7 mm Slot pitch: 160 mm Position measurement is performed via an ROD 250 rotary encoder. Condition: Very good (used) Hnjdpfxefk R Tdj Aazor Optionally available with machine base (travel path = 2000 mm) About us: MBM Maschinenservice & Gebrauchtmaschinen GmbH is an independent specialist for SHW machine tools. Our main focus is on tool milling machines. Our services include spare parts supply, on-site customer service, machine overhauls, and control system modernizations. Services: - Used machines - Spare parts - Customer service - Machine service - Machine overhauls - Control system modernization

Tahun pembuatan: 1995, Kondisi: bekas, Pressure: 125 t Stroke: 10–80 mm Stroke rate: 240 strokes/min Slide adjustment: 80 mm Table area: 850 x 600 mm Ram area: 760 x 550 mm Passage opening in table: 850 x 130 mm, adjustable Table height: 1100 mm Ram bore diameter: 50 mm Total power requirement: kW Hjdpfx Aelp U Nqoazonr Machine weight approx.: 13 t Required space approx. (WxDxH): 3000 x 2000 x 3300 mm Pneumatic clutch-brake combination Manual ram adjustment Manual stroke adjustment Machine number: 212341 Centralized oil lubrication Roll feed: Alba GVHY300 Straightening machine: Soprem BRM 19/150/16/U

Kondisi: diremaj di bengkel (bekas), bsta-110h-vorschub-bbv-202-120 Hnodpjizi Hmofx Aazor

Tahun pembuatan: 1996, Kondisi: sangat baik (bekas), Panel distribusi tegangan tinggi dengan penutup logam dan berisolasi udara – 6kV 1250A 40kA, pabrikan ABB, tahun pembuatan 1996, tipe SR7, komponen VD4, pemutus sirkuit ABB, perlindungan SPAJ, SPAU ABB, tegangan kontrol 220VDC, berfungsi penuh, kondisi sangat baik. 2 x panel input dengan pengukuran tegangan, 2 x panel pengukuran tegangan, 6 x terminal keluaran, 1 x konektor (2 panel), total 12 panel. Hodpfsg Ur Nfex Aazenr

Kondisi: baru, Fungsionalitas: berfungsi sepenuhnya, tekanan: 26 batang, daya: 47 kW (63,90 hp), suhu: 305 °C, Set Generator Turbin Uap Howden 4,7 MW (Proyek Dibatalkan) – Belum Pernah Digunakan Tersedia Segera | Kondisi Asli OEM dari Pabrik | Mendapatkan Seluruh Manfaat Garansi Hindari waktu tunggu manufaktur OEM standar selama 12 hingga 18 bulan. Turbin Uap Howden 4,7 MW berperforma tinggi ini benar-benar belum pernah digunakan, terjaga dalam kondisi bersih pabrik, dan tersedia segera akibat pembatalan proyek utilitas baru-baru ini. Ditawarkan pada tingkat investasi yang sangat menarik, aset ini merupakan peluang utama untuk implementasi cepat di proyek energi terbarukan, kogenerasi industri (CHP), ataupun pembangkit listrik mandiri (IPP). Spesifikasi Teknis · Produsen: Howden · Daya Keluaran: 4,7 MW · Kondisi: Belum Pernah Terpasang / Belum Pernah Digunakan (Proyek Dibatalkan) · Tekanan Uap Masuk: 26 bar (±377 psi) · Suhu Uap Masuk: 305°C – Uap Superheated · Garansi: Dalam masa garansi aktif OEM (Tunduk pada protokol verifikasi/transfer) · Status: Disimpan dengan protokol preservasi berstandar OEM di dalam gudang pabrik. Syarat Komersial · Harga: Atas permintaan (Hanya untuk peminat serius). Hjdpfx Aaszcx U Dozenr · Lokasi: Gudang Pabrik (FOB Jerman). Dokumentasi & Cakupan Penawaran Tersedia Atas Permintaan Pembeli serius dan perwakilan EPC yang memenuhi syarat akan mendapatkan akses ke dokumen teknis lengkap setelah menandatangani NDA, meliputi: · Gambar General Arrangement (GA) dan P&ID. · Rincian Cakupan Penawaran (inti turbin, girboks, spesifikasi generator/alternator, serta auxiliary skid). · Catatan penyimpanan OEM, dokumen preservasi, dan persyaratan transfer garansi. · Protokol uji pabrik bersertifikat

Kondisi: hampir baru (bekas), Tahun pembuatan: 2015, daya nominal: 1.300 kW (1.767,51 hp), kecepatan rotasi (min.): 1.493 rpm, kecepatan rotasi (maks.): 1.493 rpm, tegangan masuk: 6.000 V, frekuensi input: 50 Hz, berat keseluruhan: 6.100 kg, 1 unit asynchronous electric motor Manufacturer: Reform Elektromotorenbau GmbH Type: Y2-500-4 Power: 1300 kW Speed: 1493 rpm Voltage: 6000 V Current: 151.4 A Power factor (cosΦ): 0.86 Insulation class: F Frequency: 50 Hz Protection class: IP55 Design: Foot-mounted (B3) Duty type: S1 continuous duty Weight: 6100 kg Year of manufacture: 12/2015 Bearings: NU228C3 / 6030C3 and NU228C3 Cooling: Air Hjdjv I Alyopfx Aazjnr Shaft height: 500 mm

Kondisi: sangat baik (bekas), Tahun pembuatan: 2018, Fungsionalitas: berfungsi sepenuhnya, kedalaman pengeboran: 1.600 mm, panjang pemakanan sumbu X: 3.000 mm, panjang umpan sumbu Y: 2.100 mm, panjang umpan sumbu Z: 1.500 mm, berat keseluruhan: 50.000 kg, kecepatan pemakanan sumbu X: 10.000 m/menit, laju pemakanan gandar Y: 10.000 m/menit, laju pemakanan sumbu Z: 10.000 m/menit, kecepatan spindel (maks.): 4.500 rpm, diameter bor: 40 mm, panjang meja: 2.100 mm, lebar meja: 1.900 mm, CNC Heidenhain iTNC 640 AXES OF MOVEMENT Maximum drilling depth in a single operation, V axis: 1,600 mm Table travel, horizontal movement X axis: 3,000 mm Vertical movement Y axis: 2,100 mm Column approach movement (milling), Z axis: 1,500 mm Tilting of drilling slide (resolution 0.001°), A axis: +30°/-15° Table rotation (resolution 0.001°), B axis: 360° Maximum axis feed rate: 10,000 mm/min DEEP HOLE DRILLING SPINDLE ISO 50 AND MILLING Solid drilling section: 5 - 25 mm Maximum drill bit diameter: 40 mm AXES OF MOVEMENT Maximum drilling depth in a single operation, V axis: 1,600 mm Table travel, horizontal movement X axis: 3,000 mm Vertical movement Y axis: 2,100 mm Column approach movement (milling), Z axis: 1,500 mm Tilting of drilling slide (resolution 0.001°), A axis: +30°/-15° Table rotation (resolution 0.001°), B axis: 360° Maximum axis feed rate: 10,000 mm/min DEEP HOLE DRILLING SPINDLE ISO 50 AND MILLING Hnodpoywnr Nsfx Aazer Solid drilling section: 5 - 25 mm Maximum drill bit diameter: 40 mm Spindle speed (adjustable): 1 – 4,500 rpm Spindle power S1: 17 kW Spindle torque: 324 Nm Standard attachment for drilling tools: Ø 25 x 70 mm Maximum internal spindle pressure: 120 bar Taper type: ISO 50 DIN 69871/A Coolant: YES ROTARY TABLE Rotary table dimensions: 1,900 x 2,100 mm Rotary table resolution (0.001°), B axis: 360° Table load capacity in rotation: 20,000 kg T-slots: 22 mm OIL SYSTEM Hydraulic pump motor power: 4 – 7.5 kW Self-regulating oil pressure: 15 – 120 bar Self-regulating oil flow rate: 5 - 80 l/min Oil tank capacity: 800 – 1,000 L Cooled oil temperature: 25 – 32 °C Filtration degree: 16 micron MACHINE DIMENSIONS & WEIGHT: Width x Length x Height: 7,000 x 7,900 x 4,700 mm Machine weight: 50,000 kg WORKING CHARACTERISTICS FOR GUN DRILLING Maximum depth: 1,600 mm Maximum rotation speed: 4,500 rpm Minimum drilling diameter: 6 mm Maximum drilling diameter: 40 mm THREADING HEAD “IMSASISTEM” WORKING CHARACTERISTICS Max rotation speed: 4,500 rpm Maximum threading on C40 steel: M 36 Machine equipped with: • Remote Heidenhain electronic handwheel • ISO 50 tool changer magazine with 40 positions • 4,000 m³/h fume extraction system • Air/oil supply through spindle center • M24 threads on table side • Various tools and work equipment • Tool rack with various drill bits • Operation and maintenance manual, CE declaration of conformity

Kondisi: baru, Dijual stok mesin baru, sekitar 1.500.000 kg. Penjualan dilakukan dalam kelompok. Jumlah minimum yang dipesan adalah 50.000 kg. Semua mesin dalam kondisi baru dan juga bekas setelah diperbaiki. Jumlahnya sekitar 3.000 unit. Hnjdpfx Aajzgu D Iozjr Berbagai merek produsen: Siemens, ČKD, MEZ, dll. Harga per 1 kg adalah 1,50 Euro.