Kondisi: baik (bekas), dengan elemen pemanas, jangkauan 920 mm, bahan 0,4-2 mm, kecepatan feeding sekitar 15 m/menit, kebutuhan ruang 1400 x 600 x 1600 mm, berat sekitar 350 kg Kdsdpoyayzasfx Aa Nsg kondisi baik Harga ex lokasi Transportasi dapat diatur dengan biaya tambahan!

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2004, This Josting ZFS 2800 veneer guillotine was manufactured in 2004. It features a cutting length of 2810 mm and a feed height of 80 mm, suitable for a cutting range of 20 - 470 mm. The machine is equipped with a light barrier safety system, high-lifting protective grilles, and a telescopic positioning control for enhanced operational safety and precision. Take advantage of this opportunity and purchase this Josting ZFS 2800 veneer guillotine. Contact us for further information about this machine. Additional Equipment • Light barrier safety device • Safety-oriented electrical control • High-lifting protective grids • Guide light for cut indication • Telescopic positioning control • Fast table drive with oscillating and pulling blade movement Kjdoyap Snspfx Aa Njdg • Simultaneous cutting with upper and lower blades • Automatic sequences of table, pressure beam, and blade movements • Intermittent operation with low-noise drive • Precision hydraulics with two pressure levels and high-quality valves Machine Advantages Technical Machine Advantages • Cutting length: 2810 mm • Feed height: 80 mm • Cutting range: 20 - 470 mm • Pulling movement of blades: approx. 20° • Operating voltage: 400 V • Frequency: 50 Hz Additional information Supplied with operating manual Complete and ready for connection

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2025, gaya penekanan: 122 t, Additional Equipment • Mylar film attached to the upper and lower press plates • Electronic Flatness Control (EFC) for protection against improper loading Machine Advantages Technical Machine Advantages • Dimensions of heating plates: 3000 x 1300 mm • Number of heating plates: 2 pcs • Number of stages: 1 • Opening height: 370 mm • Maximum temperature of the heating medium: 120°C • Operating temperature: 70–90°C • Installed electric heating power: 18 kW • Operating voltage: 400 V – 50 Hz – 3 ph Additional Information Features: - 4.3" SIEMENS TFT touchscreen - Digital press timer - Digital temperature controller - Digital working pressure controller - Day/week timer for heating activation - Automatic hydraulic pressure calculation - Fault indication and PLC control - Storage and recall of up to 200 work programs - Prepress pressure and time settings Safety Devices: Kodpfsyan Sgsx Aa Nedg - Two-hand operation starter with safety circuit - Safety pull-cord around the machine - Safety support for lower press table - Protective cover for frame/drive - Safety instruction decals - Compliance with CE standard - CE Declaration of Conformity Specially processed heating plate surface made of solid steel Deactivation of the left cylinder row

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2025, panjang langkah: 400 mm, This OMC PL 90s veneer press was manufactured in 2025. It features a platen size of 3000 x 1300 mm, an upward stroke of 400 mm, and a pressing force of 90 tons over 80% of the surface area. Equipped with electronic heating plates by Elkom, it ensures a maximum temperature of 120°C. The hydraulic system consists of a two-stage power unit with noise reduction and a pump for rapid opening and closing. Safety features include a safety cable, an emergency stop button, and two-hand operation. Please contact us for further details on this machine. Machine Advantages Technical Highlights • Platen size: 3000 x 1300 mm • Stroke direction: upward stroke (from bottom to top) • Plate type: Elkom electronic plates • Pressing force: 90 tons over 80% of the surface • Press cylinders: 6 x Ø 70 mm • Specific pressure: 2.05 kg/cm² over 100% of the surface, 2.56 kg/cm² over 80% of the surface • Loading/Unloading side: 3000 mm • Heating system: electronic, 25.4 kW, maximum temperature of 120°C • Automatic opening with timer Additional Information Hydraulic System Two-stage unit with submersible pump for noise reduction and lubrication of rotating parts. Pump for rapid closing/opening (high flow – low pressure 35 l/min), pressing pump (low flow – high pressure 1.6 l/min). 2 HP electric motor. Control/Safety valves: maximum pressure valve, pressure holding valve (check valve), pre-release pressure valve, and solenoid valve for oil drain. Kdjdpsyalmbefx Aa Nog Control Panel and Electrical System 2 temperature controllers for platen temperature adjustment Manometer for pressure control with automatic pressure equalization system Main On/Off switch Two manual safety buttons for closing the press Timer for automatic opening Selector switch for manual or automatic opening of the platen after the work cycle On/Off switch for the top and bottom platen heating elements Safety Systems Timed two-hand control for closing the press Safety cable on all four sides of the press Platen locking mechanism for maintenance Protective guards for rack-and-pinion units Safety labels and warning instructions Operation and maintenance manual Complies with CE standards Press Structure Manufactured from composite and welded steel Fitted with a rack-and-pinion guide system for precise parallel movement during platen closing/opening. Elkom Heating Plate Electric plates with electrical resistances Composed of a chipboard core with an aluminium plate, where electrical resistances are mounted Maximum working temperature: 120°C Maximum shear force: 7 kg/cm²

Kondisi: siap digunakan (bekas), Tahun pembuatan: 1998, This ITALPRESSE DS 130 was manufactured in 1998. A robust veneer press, it comes equipped with a motorized infeed table featuring PVC belt, and an automatic loading system for efficient panel handling. The press offers a maximum total pressing force of 110 tons and a heating plate size of 3500 x 1400 mm—ideal for high-end veneering applications. Contact us for more information about this machine. Additional Equipment • Motorized infeed table with PVC belt • Motorized loading table for manual panel assembly and automatic loading into the press along the 3500 mm side • Solid steel heating plates, fully drilled and milled • Automatic loading and unloading of panels along the 3500 mm side Machine Advantages Technical Machine Advantages • Maximum total pressing force: 110 tons • Daylight opening: 140 mm Kdjdpeyall Rjfx Aa Nsg • Power supply: 400 V EU / 50 Hz / 3 Ph. + PE • Electric thermal oil heater: 18 kW • Devices for adjustment of working height for level operation even on uneven floors // devices for belt tension and centering adjustment with foot switch • Frame constructed from assembled and welded Fe430 steel beams • CNC-machined frameworks for three-dimensional parallelism • Hydraulically controlled planarity with 4 rack-and-pinion mechanisms • Safety guards and protection devices in compliance with CE regulations • Levelling devices at the base of the columns for uneven floors Additional Information Overhauled – sold without warranty Control panel with electric manometer, buttons, and selector switches Lifting lugs for crane transport

Kondisi: bekas, Fungsionalitas: berfungsi sepenuhnya, Panjang jangkauan 630 mm Ketebalan veneer 0,4 - 2 mm Kecepatan maju 7 m/menit Kedpex U Tggofx Aa Nodg Tegangan 220 V satu fasa Dimensi keseluruhan: 950 x 500 x 1180 mm (T) Berat 95 kg

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2019, FORMAT4 HVP Tipe 4 ini diproduksi pada tahun 2019. Mesin ini dirancang untuk integrasi ke dalam sistem pemanas yang sudah ada dan dapat menekan pada suhu hingga 90°C. Pelat baja yang kokoh mendukung tekanan maksimum hingga 5kg/cm², sehingga sangat ideal untuk pemrosesan veneer. Manfaatkan kesempatan untuk membeli mesin penekuk veneer FORMAT4 HVP Tipe 4 ini. Hubungi kami untuk informasi lebih lanjut mengenai mesin ini. Keunggulan Mesin Keunggulan Teknis Mesin Kdsdpfxjx U Tv Ij Aa Nog • Untuk sambungan pada sistem pemanas yang sudah ada / suhu penekanan hingga 90°C / pelat baja dapat menahan tekanan maksimum hingga 5kg/cm²

Kondisi: bekas, Kedalaman stang: 420 mmLaju umpan konstan: sekitar 6 m/menitPenggerak motor listrik: 25 W, 190 V=Tegangan sambungan: 110 - 235 V, 50 - 60 HzTotal daya terpasang: 110 WKepala pemanas: sekitar 75 WBerat bersih: sekitar 22 kg dengan pedal kakiLokasi gudang: Nattheim Kdjdpfx Aasx Upgco Nog

Kondisi: bekas, Lokasi gudang: Pemasok Kedpfex Upflox Aa Njdg

Kondisi: bekas, panjang total: 4.000 mm, berat keseluruhan: 5.000 kg, tekanan kerja: 348 batang, lebar kerja: 1.300 mm, lebar pelat: 1.350 mm, Mesin Press Veneer Bürkle U140 Permukaan kerja: 5 unit Pelat antara: 4 unit Ukuran pelat: 3050 x 1350 mm Dimensi kerja: 3000 x 1300 mm 8 silinder hidrolik Tekanan permukaan maks.: 5 kp/cm2 Kodpfxjya Dygo Aa Njdg Tekanan operasi maks.: 348 bar Media pemanas: air hangat dari sistem pemanas sentral Pendinginan: sirkuit pendingin dengan pompa WILO, tangki ekspansi, perpipaan Berat sekitar 5.000 kg Kondisi teknis pelat dan sistem hidrolik baik

Kondisi: sangat baik (bekas), Tahun pembuatan: 2007, Fungsionalitas: berfungsi sepenuhnya, lebar total: 2.400 mm, persyaratan ruang panjang: 9.000 mm, lebar kerja: 1.600 mm, Mesin penyambung veneer lintang / Mesin penyusun lintang, Merek: Kuper Tipe: ACR CrossRunner 1600 Tahun pembuatan: 2007 Mesin penyusun lintang dengan lebar kerja sempit untuk strip veneer yang sudah dilem sebelumnya. Mesin ini bekerja secara lintas alur dan jauh lebih cepat daripada mesin searah, sehingga merupakan alternatif ekonomis, misalnya, untuk daun pintu laminasi lintang atau komponen furnitur kecil. Lebar kerja: 1600 mm (arah serat) Lebar strip veneer: mulai sekitar 60 mm Ketebalan veneer: sekitar 0,3 - 2,5 mm Kecepatan penghantar: sekitar 30 m/menit Jenis lem: PVAc atau urea Dengan sistem penumpukan otomatis Kontrol: Siemens Simatic dengan layar sentuh Kjdpfxsyayumo Aa Nedg Tegangan: 400 V, 50 Hz, 3 fasa Arus nominal: 16 A Ukuran pemasangan: sekitar 2400 x 9000 mm (L x P)

Kondisi: bekas, Stack paper cutting machine, stack cutter, guillotine cutter SCHNEIDER Type Senator 155 Rubber, paper and veneer shear, plastic shear, fabric shear Guillotine cutter for paper, cardboard, rubber, wood, and veneer Paper shear, rubber shear, plastic shear, paper and veneer shear Machine no. 60178 Year of manufacture: 1968 Cutting length: 1550 mm Cutting height: approx. 125 mm Working height: 140 mm Back gauge max.: 1550 mm Blade drive motor power: 5.5 kW Power supply: 380 Volt, 50 Hz - Two-hand operation for stroke release - Automatic clamping—presses the paper stack onto the table Kodpfxodzqnyo Aa Nedg - Manual clamp and stroke release via foot switch (functional) - Back gauge up to 1550 mm (can be manually adjusted via a handwheel) - Retrofitted electrical control, non-functional, without circuit diagrams, without operating manual - Back gauge adjustment by servomotor (motor, controller, and control included, not functional) Space required (L x W x H): 325 x 270 x 165 cm Transport space requirement without disassembly: length 330 cm x width 270 cm x height 175 cm Transport space requirement with disassembly: length 550 cm x width 220 cm x height 175 cm (machine + table separate) Machine: length 270 cm x width 190 cm x height 175 cm Gauge table: length 240 cm x width 170 cm x height 120 cm Weight of assembled machine: approx. 5,000 kg (without the transport steel plate) Good condition Ideal for cutting paper, cardboard, leather, cork, rubber or fabric-reinforced rubber. Sales price does not include the 20 mm steel plate on which the machine is stored in the warehouse. (Price for the steel plate: 900 EUR net)

Kondisi: baik (bekas), Kondisi umumnya baik Panjang potong 2600 mm Ketebalan veneer hingga 3 mm Termasuk skala untuk pengaturan Ksdpfxjyakyts Aa Nsdg Secara keseluruhan mesin yang sangat bagus untuk pengolahan veneer. Jangan ragu untuk menghubungi kami jika ada pertanyaan atau minat!

Kondisi: hampir baru (bekas), mesin penempel benang dengan lem Kdodpfox U Dhzex Aa Nsg penjahitan zig-zag elemen pemanas dengan hembusan udara pengoperasian dengan pedal daya 380V

Kondisi: sangat baik (bekas), Press Furnir OTT JU 2513 - bekas - plat baru, tali darurat, pengoperasian dengan tombol, plat eloksasi ----- Data Teknis ----- Luas tekan: 2.550x1.350 mm, Daya per pelat pemanas: 9.100 W, ketinggian bukaan maks.: 400 mm, jumlah silinder: 4 buah Info Kualitas: - Hidrolik diperiksa - Plat diganti Kdjdsx R Sydjpfx Aa Njg - Kekerataan plat diperiksa - inspeksi dasar lengkap - pembersihan dasar lengkap - Listrik diperiksa - siap digunakan segera

Kondisi: bekas, - Dokumentasi tersedia: Tidak Kdodpfjwivv Tsx Aa Nog - Sertifikat CE tersedia: Tidak - Jumlah rol lem [buah]: 2 - Diameter rol [mm]: 200 - Lebar kerja maks [mm]: 1300 Informasi Keuangan PPN: Harga yang tertera belum termasuk PPN PPN/Pajak Margin: PPN dapat dikreditkan untuk pengusaha Pengiriman dan trade-in setiap saat dimungkinkan untuk semua barang dari sektor industri Yorick Diebels

Kondisi: hampir baru (bekas), panjang rak: 3000 mm lebar rak: 1300 mm jumlah piston: 6 tahun produksi: 2004 pemanasan air berat: 3900 kg 400 V Kodox Thnispfx Aa Nodg jarak bebas: 400 mm tanda CE

Tahun pembuatan: 1975, Kondisi: baik (bekas), Fungsionalitas: berfungsi sepenuhnya, Maschine zum Schälen / Zentrier- und Beschickungseinrichtung Kdedpfxot D A S Ie Aa Nog Schälmaschine Angelo Cremona SFL 2700 x 1100 - Baujahr 1975 Zentrier- und Beschickungseinrichtung CTA 4 - Baujahr 1976 Furnierabwickler Bertram - Baujahr 1995 Abbau durch den Käufer

Kondisi: baik (bekas), Fungsionalitas: berfungsi sepenuhnya, Daya jangkau 420 mm Kecepatan pemajuan 6 m/menit Ketebalan veneer 0,4 - 2 mm Koneksi listrik 230 V Mesin 'start' melalui pedal kaki Mesin siap pakai segera Kedpfxsx Uphto Aa Njdg

Kondisi: bekas, maks. ketebalan veneer: 2,0 mm, min. ketebalan veneer: 0,4 mm, bahan penyambung: benang lem dengan pemanasan udara panas, tekanan udara diperlukan: ya, cakram: ya, untuk mengangkut veneer di atas meja veneer; kontrol melalui pedal kaki; jenis mesin: model berdiri; kecepatan makan: 7 m/menit; jangkauan lengan: 900 mm; berat sekitar: 185 kg; dimensi: 1400 x 500 x 1680 mm. Lokasi gudang: Nattheim Ksdpoxgqmxjfx Aa Nedg

Kondisi: baik (bekas), Fungsionalitas: berfungsi sepenuhnya, ANGEL CREMONA DRYER Ksdjvndvyjpfx Aa Njdg Model ER 18, 4400mm, 3 decks, steam heated Steam consumption at 10 bar: 2,200 kcal/hour Water consumption at 185°: 1,100,000 kcal/hour PRODUCTION Birch thickness: 1.2 mm Initial moisture: 80% Final moisture: 6% Load: 85% 4.2 m³/hour Installed power: 95.5 kW Machine disassembled, requires servicing.

Kondisi: bekas, Tahun pembuatan: 1999, Fungsionalitas: berfungsi sepenuhnya, Complete line consisting of: 1. Angelo Cremona Peeling Lathe – detailed description available below 2. Angelo Cremona Dryer – description and photos available in the listings 3. CMP Press – description and photos available in the listings 4. Imeas Sander – description and photos available in the listings 5. Raute Splicer – description and photos available in the listings PEELING PLANT comprised of: Log Centering Loader 1. Model CE08 2. Angelo Cremona 3. Positions the log for loading onto the peeling lathe 4. Power supply 400Vac/50Hz – 50kW Maximum hydraulic pressure 100 bar Compressed air consumption 0 L/min Weight kg Maximum dimensions 600x300x400 5. Production capacity: 4 logs per minute Peeling Lathe 1. Model SFH870 2. Angelo Cremona 3. Produces a veneer ribbon by turning the log 4. Power supply 400Vac/50Hz – 240kW Maximum hydraulic pressure 100 bar Compressed air consumption 10 L/min Maximum dimensions 600x400x300 5. Production capacity: 50 cubic meters per shift Cutting and Sorting Line 1. Model TSR27 Ksdpfevm An Ejx Aa Nsdg 2. Angelo Cremona 3. Transports the peeled veneer strip to the guillotine for optimized sheet cutting 4. Power supply 400Vac/50Hz – 70kW Maximum hydraulic pressure 100 bar Compressed air consumption 0 L/min Maximum dimensions 300x200x200 5. Production capacity: 50 cubic meters per shift Grading Line and Vacuum Stacker 1. Model LTR27 2. Angelo Cremona 3. Separates and stacks recovery sheets from full-size sheets 4. Power supply 400Vac/50Hz – 180kW Compressed air consumption Maximum dimensions 300x1300x500 5. Production capacity: 50 cubic meters per shift

Kondisi: sangat baik (bekas), Tahun pembuatan: 1994, Josting Mesin Pemotong Paket Veneer Tipe: EFS 2300 L - Tahun 1994 Panjang potong: 2.300 mm Tinggi masukan maks: 80 mm Tirai cahaya pengaman FIESSLER Ksdpfxjxgbwze Aa Nsdg Lampu penunjuk posisi potong Pembatas paralel dapat disetel secara motoris, penyesuaian halus dengan roda tangan Daya terpasang: 7,7 kW Berat: 2.700 kg Ukuran: 3.610 x 1.700 x 1.680 mm Ex stock: - tersedia segera -

Tahun pembuatan: 1985, Kondisi: sangat baik (bekas), Press lem pengikat tepi untuk veneer, kayu solid, dan plastik, model HFK 2200 untuk memotong tepi selama waktu pengepresan. Dengan menggunakan lem pengeras panas, waktu pengepresan untuk tepi veneer adalah 20 hingga 30 detik. Ukuran kerja maks. sekitar: 1.400 x 2.500 mm. Pemanas: 1,7 kW. Press tepi elektro-pneumatik Haug HFK 2200 untuk menekan material tepi pada kayu dengan pemanas. 3 perpanjangan meja. Meja kerja dapat diputar. Lokasi: stok ready di 54634 Bitburg. - tersedia segera - Ksdpfew Apqqox Aa Njdg

Kondisi: bekas, Tahun pembuatan: 1996, Ukuran tekan: 2550 x 1350 mm. Pelat: Eloxasi emas. Tekanan total: 80 t. Tekanan spesifik: 2,8 - 4,0 kg/cm². Silinder hidrolik: 4 x 90 mm. Jarak buka dan langkah tekan: 400 mm. Tali pengaman. Rangka pengaman. Operasi tombol. Daya terpasang total: 19,3 kW. Lokasi stok: Pemasok. Kdodpfx Aaexy Tl Ro Nog