Derek jib pilar Derek jib slewing Derek jib rantai Kerekan rantai

Demag KBK Kran Drehkran Hallenkran L 3m Demag KBK1 250Kg + Demag PK Kettenzug

Tahun pembuatan: 1979, Kondisi: bekas, nomor mesin/kendaraan: RS82/12, Technical specifications: 1x Demag KBK 1 column-mounted slewing jib crane, rated capacity 250 kg with PK chain hoist Load capacity at full outreach: 250 kg / 0.25 t Height: approx. 3 m Underside of boom: approx. 2.5 m Pgsdpfx Anjvv N Auowjl Outreach: 3 m Hook height: approx. 2 m Total weight: approx. 350 kg With 250 kg chain hoist Incl. pins, cable carrier, trolley, end cap, etc. Slewing range: 300° Connection: 400V, 16A Crane is dismantled and immediately available Location of item: 75053 Gondelsheim Further cranes available with lifting capacities from 80 to 5000 kg; please enquire See pictures Shipping by freight forwarder or collection strictly by appointment

Kondisi: bekas, nomor mesin/kendaraan: 87 54 41 57, Grinding wheel diameter: 200 mm Grinding wheel width: 30 mm Grinding wheel bore: 51 mm Grinding wheel speed: 3,000 rpm Electrical connection: 380 V, 630 W Space requirement: 600 x 260 x 320 mm Pedpfx Aodc Swusnwegl Weight approx.: 23 kg

Kondisi: baru, Load capacity 500 kg Number of suction pads: 6 Diameter of suction pads: 215 mm Pgedpfx Anjq Sc Auswsl Vacuum Lifter VH 6-500 For horizontal transport of smooth, dry, and airtight panels. Robust load-bearing steel construction, painted in RAL 2000, with low dead weight. Consisting of: - 1x Galvanised longitudinal beam, length 2,400 mm - 3x Galvanised crossbeams, length 1,000 mm - 6x Spring-mounted, articulated, and adjustable suction pad holders - 6x Suction pads Ø 215 mm; in case of wear, seals can be inexpensively replaced without tools, separate from their metal carrier - 6x Ball valves to individually shut off suction pads, allowing smaller formats to be lifted without having to move the pads or beams - 1x Spiral connection cable, small coil: * Extension length 3,500 mm, designed as extension cable with CEE plug and socket * Routed alongside the load chain to the lifting device - Low-maintenance, high-quality, dry-running rotary vane vacuum pump with suction capacity of 8 m³/h and final vacuum of 85% (150 mbar) - Electrical connection: 3 phases 230/400 V + PE, 50 Hz, with cable (approx. 0.5 m) and CEE plug (16 A). Isolation transformer integrated into the control system (necessary if the vacuum lifter is connected via the crane trolley and no neutral conductor is present) - Operating handle extendable up to 1,000 mm from the centre of the beam - Stable sheet metal pocket for your crane controls included, at no extra charge - Operation "Suction / Release" via hand slide valve: Wear-free and very robust hand slide valve ensures secure suction and release following actuation of the release button (double release according to EN 13155) - Control and safety device for vacuum lifter: * Sturdy control box * Contactor circuit for the vacuum pump * Safety warning device with acoustic alarm * Vacuum gauge with danger zone indicator * Large vacuum accumulator tank with safety non-return valve * Double release operation when unloading - Fine dust filter to protect the vacuum pump - Comprehensive and easily understood documentation Guarantee against material and manufacturing defects for one year under single-shift operation (excluding wear parts). Initial safety inspection UVV 18, VBG 9a, with CE declaration of conformity – according to EN 13155 - Packaging for truck transport.

Kondisi: bekas, Clamping plate - table of a long planing machine - Table width / Clamping width: 1845 mm Table length / Clamping length: 5505 mm 7 longitudinal T-slots for T-slot nuts: M 30 T-slot pitch: 263 mm Total length: 6230 mm Pjdpfx Ansbn Amfjwjgl Total plate height: 350 mm Weight: 11 t

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2007, jam operasional: 22.605 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 100 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.600 mm, lebar bal: 1.100 mm, tinggi bal: 1.100 mm, berat bal: 1.400 kg, berat keseluruhan: 36.000 kg, kapasitas tangki oli: 1.300 l, tahun perombakan terakhir: 2025, For sale is a refurbished baler with 100 t press force, large-format bales 1100 x 1100 mm, 75 kW drive power and 10-way cross-tying. Technical specifications baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main press force: 100 t Pre-press force: 50 t Operating hours: 22,605 h Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Connected load: 126 kW Total current consumption: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput at bulk density of: - 30 kg/m³: approx. 16 t/h - 50 kg/m³: approx. 25 t/h - 100 kg/m³: approx. 47 t/h Bale weight up to 1,400 kg, depending on material and bale length Hydraulic oil tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operating panel: Schneider MAGELIS Touch Baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions without baler: 11,765 x 2,500 x 3,450 mm (L x W x H) Baler weight: approx. 36 t Remarks: The baler has been partially overhauled, serviced in our workshop, and tested after completion of work before being stored. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment works have been carried out: - Descaling and partial repainting of the baler. - Hydraulic oil tank drained, oil and air filters replaced. - New hydraulic oil filled. - All hydraulic hoses renewed. - Main hydraulic cylinder, two cylinders of the pre-press flap and the channel cylinder disassembled, dismantled, inspected, cylinder tubes honed, all seal kits replaced and final pressure tested. - Pre-press flap with bearings and bearing blocks disassembled. First and third circular arc segments removed and newly welded in. - Both shaft bearings for the pre-press flap renewed. - Upper material guide on the frame for the pre-press flap renewed. - Plunger disassembled, inspected and both front roller guides renewed. - Material guides and wear strips at the sides and on the bottom of the plunger cut out and newly welded in. - Horizontal and vertical needle and tying units disassembled, dismantled, inspected, plastic slide plates, bearings on twister shafts, and wire divert rollers with bearings in the needle heads renewed. - Both bronze slide rails left and right in the frame cover for the plunger renewed. - Both wire divert units left and right, including bale retaining clamps, fully renewed. - Wire infeed unit including hydraulic cylinder below the needle passes fully renewed. - Wire mark/scoring in the bottom and sidewalls of the channel welded up and smoothed. - General maintenance and service work carried out in line with manufacturer specifications. - Baler tested in manual and automatic mode, accepted and stored after completion of refurbishment works. Pedpovf E Avsfx Anwogl We assume no liability for the technical details or possible errors.

Kondisi: hampir baru (bekas), Tahun pembuatan: 2000, jam operasional: 25.000 h, jarak pergerakan sumbu X: 10.300 mm, jarak lintasan sumbu Y: 2.000 mm, jarak gerak sumbu Z: 1.800 mm, kecepatan pemakanan sumbu X: 10 m/menit, laju pemakanan gandar Y: 10 m/menit, laju pemakanan sumbu Z: 10 m/menit, posisi kepala milling: 2.5 x 2.5 °, kecepatan spindel (maks.): 3.000 rpm, kecepatan spindel (min.): 60 rpm, lebar meja: 3.300 mm, panjang meja: 12.000 mm, diameter pemasangan: 50 mm, tinggi total: 48.750 mm, lebar total: 100.000 mm, panjang total: 212.000 mm, berat keseluruhan: 100.000 kg, Duplex-Fräsen bestehen aus zwei Maschinen, die sich gegenüberstehen und entweder separat oder als Einzelmaschine betrieben werden können. Das Werkstück kann mit zwei simultan arbeitenden Spindeln bearbeitet werden. Produktivitätssteigerung von bis zu 50 % im Vergleich zu konventionellen Lösungen wie einzelnen Fräsmaschinen Erhöhung der Fertigungsgenauigkeit durch Komplettbearbeitung des Werkstücks in einer Aufspannung (in den meisten Fällen) Eine einzige Bedienperson kann die Duplex-Fräsmaschinen steuern Geringerer Platz- und Investitionsbedarf im Vergleich zu zwei Einzelmaschinen Schnelle Amortisation der Investition dank hoher Produktivität Die Duplex-Lösung ermöglicht verschiedene Konfigurationen: Einzelner Arbeitsbereich, Pendelbearbeitung Pgjdperx Rxtofx Anwjl Geeignet für die Bearbeitung von Baggerarmen und Auslegern, z.B. für CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Achse: 10.300 mm Y-Achse: 2.000 mm Z-Achse: 1.800 mm Tischlänge: 12.000 mm Tischbreite: 3.300 mm Tischbelastung: 100.000 kg Antriebsleistung der Spindel: 22/30 kW Spindeldrehzahlen: 60–3.000 U/min Spindelaufnahme: 50 ISO / BT / MK Vorschub X-Achse: 10.000 mm/min Vorschub Y-Achse: 10.000 mm/min Vorschub Z-Achse: 10.000 mm/min Fräskopf-Autopositionierung: 2,5 x 2,5° Betriebsstunden: 25.000 h Länge: 21.200 mm Breite: 10.000 mm Höhe: 4.875 mm Gewicht: 100.000 kg

Kondisi: baru, Lifting capacity in kg: 1,000 kg Reach: 4,000 mm Height: 3,000 mm (underside of jib) Total column height: 3,790 mm Slewing range: 270 degrees Total weight: approx. 525 kg Description: - Festoon cable system - Drag cable, cable sag approx. 800 mm - Floor-controlled operation via pendant controller Includes: - ABUS electric chain hoist Pgedexak Hxspfx Anwel - Chain hoist type GM 4 1000.5-2, double-fall - Painted in RAL 5017 traffic blue - Lifting capacity: 1 t - Hook path: 3,000 mm - Maximum hook position: 2,442 mm - Calculation basis: FEM 9.901 - Mechanism group: 2m / M5 - Lifting, 2-stage (pole-changeable): 1.3 / 5 m/min - Lifting power: 0.22 / 0.9 kW - Duty cycle: 60% ED - Switching frequency: 360 cycles/hour Overload protection The crane system meets the requirements of the Machinery Directive 2006/42/EC and the currently applicable accident prevention regulations DGUV Regulation 52 (formerly BGV D6). Included: - Anchor rods L200 (set), size LS 200 - Comprising 8 pcs. M27 mm x 800 mm with 1 steel template (500/8) - For foundation mounting, incl. grouting accessories For the alignment of the slewing jib crane, an assembly gap between the base of the column and the building floor must be provided. This assembly gap is to be grouted by the customer after approx. 4 weeks of crane operation. The illustration shows a similar crane system.

Kondisi: baru, Tahun pembuatan: 2025, kapasitas angkut: 1.000 kg, Various very heavy-duty welding tables, machined, some plasma-nitrided Sizes: - 1 x 1 meter, €1,500 - 1.2 x 1.2 meters, €1,700 - 1.5 x 1.5 meters, €1,900 - 2 x 1 meter, €2,300; plasma-nitrided €3,300 - 2.4 x 1.2 meters, €2,900; plasma-nitrided €3,900 Pgjdowu Exzjpfx Anwsl

Kondisi: bekas, Tahun pembuatan: 2006, en-GB: Technical Details: Swing diameter over bed: 500 mm Swing diameter over cross slide: 290 mm Turning length: 850 mm Centre distance: 850 mm Longitudinal travel (Z-axis): 900 mm Cross travel (X-axis): 260 mm Control: Manuaplus 4110 Spindle speed: 10 - 3000 / 2x steps rpm Spindle torque: 920 Nm Spindle bore: 70 mm Cross travel (X-axis): 8 m/min Longitudinal travel (Z-axis): 10 m/min Operating hours (power on hours): approx. 34,600 h Tailstock taper ISO: MK 5 Tailstock quill stroke: 180 mm Total power requirement: 24 kVA Machine weight approx.: 5.2 t Machine dimensions (LxWxH) approx.: 2.2 x 3.2 x 1.9 m Multifix tool holder size C 3-jaw chuck Ø 250 mm Pjdpfx Anewtct Hswegl Chip tray Manual hour counter Live centre in tailstock Operation via control panel and monitor Accessories: 4-jaw chuck Ø 250 mm with inner jaws Various chuck keys Machine lighting 8x base plates 4x wedge lifters Various pairs of jaws 1x closed steady rest Ø 100 mm

Tahun pembuatan: 2004, Kondisi: baik (bekas),