Ghiringhelli M2150 SP610 CNC 4 sumbu - ms

Ghiringhelli M2150 SP610 CNC 4 axis - ms

Kondisi: bekas, Swing diameter over bed: 2400 mm Swing diameter over support: 2200 mm Turning length: 10,000 mm Drive power: 185 kW Face plate diameter: 1650 mm Spindle speed: 1.5 - 150 rpm Max. workpiece weight: 70,000 kg Clamping diameter: 1400 mm Technical Data Working Area Maximum swing diameter over support: 2200 mm Maximum swing diameter over bed: 2400 mm Maximum turning length: 10,000 mm Clamping diameter in headstock faceplate: 300 - 1600 mm With special jaws up to 2050 mm Clamping diameter in tailstock faceplate: 300 - 1400 mm Maximum workpiece weight: 70,000 kg Main Drive, Faceplate Faceplate diameter: 2000 mm Faceplate speed, infinitely variable in 4 ranges: 1.5 - 150 rpm Maximum torque at rated speed: 220,000 Nm Main motor drive power: 185 kW Godpfx Aexddvnodtoil Flange center angle: 70° Supports Travel of grooving slide: 500 mm Travel of cross slide: 1400 mm Rapid traverse, longitudinal: 2000 mm/min Rapid traverse, cross: 800 mm/min Infinitely variable feeds, longitudinal: 0.6 - 300 mm/min Infinitely variable feeds, cross: 0.3 - 120 mm/min Maximum cutting force at support: 20,000 kg Tailstock Faceplate diameter (removable): 1650 mm Clamping diameter of faceplate: 1400 mm Flange center angle: 70° Rapid traverse: 1250 mm/min Special Equipment Copying device for first support: Copying length: 8500 mm Max. copying depth in a single pass: 500 mm Boring attachment: Boring bar: 460 x 390 mm Boring diameter: 600 - 1000 mm Maximum boring depth in one pass: 2700 mm For K_s of 200 kp/mm² - s_max = 1.5 mm/rev a = max. chip cross-section 30 mm² at an overhang of 1000 mm With increasing boring depth, reduced chip cross-section A guide rail for taper turning, adjustment angle up to 8° and a maximum taper length (in one pass) of 2000 mm, adjustment accuracy ± 5 minutes. A guide rail for taper turning, adjustment angle up to 15° and a maximum taper length (in one pass) of 1000 mm, adjustment accuracy ± 5 minutes. 125 kg auxiliary crane on spindle housing.

Kondisi: bekas, Tahun pembuatan: 2006, Travel X-axis: 600 mm Travel Y-axis: 400 mm Travel Z-axis: 400 mm Control: MSX 501 Mori Seiki Table clamping surface: 700 x 450 mm Max. table load: 350 kg Number of T-slots: 4 T-slot width: 18 mm T-slot spacing: 100 mm Spindle speed: 12,000 rpm Main spindle drive power: 18.5 / 15 / 11 kW Tool holder: BT 40 Max. torque: 110.5 Nm Front spindle bearing diameter: 70 mm Rapid traverse (x/y/z): 20,000 mm/min Feed rate: 1 - 20,000 mm/min Creep feed rate: 15 steps / 0 - 1,260 mm/min Giedpjv Az Ucjfx Adtsl Tool magazine capacity: 40 positions Max. tool width: 80 mm Max. tool diameter with free adjacent pocket: 125 mm Max. tool length: 250 mm Max. tool weight: 8 kg Chip-to-chip time: 2.8 sec Tool-to-tool time: 1.0 sec Total power requirement: 34 kVA Machine weight: approx. 7.2 t Space requirement: approx. 2.8 x 3.0 x 2.9 m Vertical machining center MORI SEIKI - NV 4000 DCG - approx. 14,000 operating hours

Kondisi: sangat baik (bekas), Tahun pembuatan: 2008, Fungsionalitas: berfungsi sepenuhnya, jarak pergerakan sumbu X: 1.500 mm, jarak lintasan sumbu Y: 700 mm, jarak gerak sumbu Z: 610 mm, daya nominal (semu): 37 kVA, torsi: 236 Nm, produsen pengendali: Heidenhain iTNC530, model controller: iTNC530, lebar meja: 700 mm, panjang meja: 1.700 mm, beban meja: 700 kg, kecepatan rotasi (maks.): 12.000 rpm, berat keseluruhan: 9.000 kg, kecepatan spindel (maks.): 12.000 rpm, jam operasional spindle: 16.580 h, daya motor spindle: 37 W, jumlah spindel: 1, jumlah slot dalam magazin alat: 48, Perlengkapan: dokumentasi / manual, konveyor serpihan, 3-axis CNC machining centre Heidenhain iTNC530 X-axis travel: 1500 mm Y-axis travel: 700 mm Z-axis travel: 610 mm Table size: 1700 x 700 mm Tool holder: SK40 Tool magazine: 48 positions Gsdpfxjvz Tyuj Adteil Rapid traverse: 36 m/min Table load capacity: 700 kg Through-spindle coolant: 20 bar Chip conveyor Electronic handwheel

Kondisi: sangat baik (bekas), Tahun pembuatan: 2010, Fungsionalitas: berfungsi sepenuhnya, Perlengkapan: dokumentasi / manual, konveyor serpihan, Control: FANUC 18i-MB Travel (X / Y / Z): 1,020 / 510 / 510 mm Feed Rate (X / Y / Z): 1 – 10,000 mm/min Rapid Traverse (X / Y / Z): 48,000 mm/min Table Size (W x D): 1,200 x 510 mm Spindle Speed: 15,000 rpm Giedpstz T Smefx Adtjl Internal Coolant Supply: 20 bar Tool Holder: BT 40 Tool Changer: 48 positions Weight: approx. 7,500 kg Dimensions (W x D x H): approx. 3,100 x 2,200 x 2,900 mm Hours: Spindle Hours: 9,310 Accessories: RENISHAW tool measurement system type OMP 40, coolant tank, machine manual, machine lamp, chip conveyor

Kondisi: baik (bekas), Manufacturer: ESTARTA Model: 301 MV Condition: Used Stock Number: 4576 Gijdpjr Ezfpefx Adtol Location: Badajoz, Spain Dimensions: 1520 x 1020 x 1260 mm Weight: 1,550 kg Wheel gap opening: 1.5 / 50 mm Max. grinding wheel width (in plunge grinding): 125 mm Work wheel dimensions (OD x ID x width): 300 x 125 x 175 mm Min. external diameter of work wheel: 220 mm Max. profile depth of work wheel: 8 mm Regulating wheel dimensions (OD x ID x width): 220 x 125 x 125 mm Min. external diameter of regulating wheel: 165 mm Max. profile depth of regulating wheel: 8 mm Work wheel motor power: 7.5 kW Regulating wheel motor power: 0.75 kW Work wheel head tilt angle: +/- 5º

Kondisi: baik (bekas), Tahun pembuatan: 2004, Kommission Nr.: Lg 34522 High-Performance Automatic Punch Press HAULICK+ROOS ROS 500 - 1250 used, in good condition year of manufacture: 2004 (without soundproof enclosure) Equipped with: - Infinitely variable drive - 2-connecting rod mechanism - Pneumatic clutch-brake combination - Stroke adjustment - Siemens PC 670 display control - Oil circulation lubrication Technical Data Press force (max.): 500 kN Stroke rate: 30 to 900 strokes/min Stroke: 12 to 60 mm Shut height (max, stroke at BDC): 320 mm Upright clearance: 1,250 mm Table area: 1,250 x 730 mm Passage opening in table: 1,160 x 140 mm Ram area: 1,250 x 450 mm Ram adjustment: 60 mm Drive power: 26 kW Weight: approx. 11,000 kg Dimensions (L x W x H): approx. 2,800 x 1,300 x 3,250 mm Godpfx Asip Uqmsdteil Equipment and Accessories: Servo Roll Feed VAMCO SP 150 year of manufacture: 2014 Passage width: max. 150 mm Material thickness: max. 3.0 mm

Kondisi: seperti baru (mesin pameran), Tahun pembuatan: 2023, jam operasional: 31 h, 3D coordinate CNC measuring machine Profitech Innometrik Advanced, gantry design (demo unit at special price) Open Cable Key features of the gantry design: - Gantry construction with low center of gravity, wide bearing separation, and optimal stiffness-to-mass ratio. - Granite guideways provide consistent thermal, dimensional, torsional, and geometric stability for the machine. - 24 air bearings ensure smooth movement of all three axes. - High dynamics for improved performance: the machine achieves acceleration rates comparable to medium and large CMMs. - Thermally stable materials and components minimize the impact of ambient temperature fluctuations on measurement results. Includes air filter and regulator. - Pneumatic counterbalance system for the Z-axis. - Granite table with M10 threaded inserts. - Passive vibration isolation pads. Technical data: Giodpfx Adodyah Sjtsl Measuring paths: X: 500 mm / Y: 600 mm / Z: 400 mm Max. workpiece weight: 250 kg Machine weight: 850 kg Overall dimensions: 1290 x 1160 x 2350 mm Accuracy according to DIN EN ISO 10360-2 and ISO 10360-4: - Volumetric probing deviation: MPEP = 2.2 µm - Volumetric length measurement deviation: MPEE = 2.2 + L / 350 (µm) Environmental conditions: Standard room temperature: 18–22°C Operating temperature: 10–35°C Compressed air supply: Minimum air pressure: 6 bar Air consumption: 90 NI/min Can also be configured as a complete package with probe system, software, commissioning, and training. (Annual maintenance and calibration also available on request.)

Kondisi: bekas, Tahun pembuatan: 2007, Mesin telah secara rutin dirawat dan berada dalam kondisi teknis yang baik. Dengan sumbu-C. Rincian teknis: Diameter piringan rencana: 1600 mm Gijdpfx Adjx Aq E Hetol Kebutuhan daya total: 80 kW Berat mesin sekitar: 25 t Kebutuhan ruang sekitar: 4,4 x 4,62 m Diameter benda kerja – maks.: 2000 mm Diameter terbesar saat facing: 1800 mm Jenis dudukan alat: ISO50

Kondisi: bekas, Tahun pembuatan: 2002, Grinding diameter: 350 mm Grinding length: 1,000 mm Centre height: 175 mm Space requirement approx. 3.6/3.5 m Photos show an identical machine with 225 mm centre height Base Model: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding Head UR with T1-T2-T3 Standard Equipment: - T1: 500 mm grinding wheel diameter - T2: 400 mm grinding wheel diameter - B-axis infinitely variable, high resolution - Marposs measurement system for tool setting - Active longitudinal positioning - GAP control at T1 and T2 from ELASO, contactless integration in the control interface - Semi-automatic balancing by ELASO integrated in the control interface - Tailstock with manual retraction - Workpiece spindle head MK5 with short taper mount DIN 55026 - Internal grinding attachment, belt-driven Options at Additional Cost: - New high-precision workpiece spindle head with torque drive - Internal grinding attachment for high-frequency spindles, 120 mm diameter - HF internal grinding spindle Fischer MFM-1224/42/31 D-21 - HF spindle with HSK interface, 24,000 rpm, with integrated GAP sensor (lead time required) - CNC-controlled C-axis - Non-circular grinding - Hydrostatic leadscrew in X - New hydrostatic system with only one pump and accumulator for better energy efficiency - Monitoring of water content in the hydrostatic system - Extraction unit Other options available on request Mechanical Overhaul: - Complete machine overhauled according to Kellenberger measuring protocol - New, service-friendly enclosure - New paintwork Electrical Overhaul: - New state-of-the-art CNC cylindrical grinder control system with BEMA cylindrical grinding interface - Rebuilt control cabinet - New drive technology - Replacement of all electrical wiring, Berus pressure switch, etc. - New absolute glass scales in X and Z - New absolute rotary encoder (for B-axis) Control System: The grinding software consists of a basic license and various options depending on the machine’s equipment. Basic software - External and internal oscillation grinding - External and internal plunge grinding - External and internal plane oscillation grinding - External and internal plane plunge grinding - External and internal cone oscillation grinding - External and internal radius grinding, radius dressed on the wheel - Semi-automatic oscillation grinding - Workpiece zeroing - Grinding wheel zeroing - Measurement of dressing diamonds - Two form diamonds - One form diamond or dressing roll (dressing roll required) - Form roll (dressing roll required) - Three flat dressers - Corrections - Z-position measurement (probe required) - GAP touch detection (touch dressing device required) OPTIONS at additional cost: Software for profile plunge grinding: - External and internal profile plunge grinding with profile wheel Profile grinding software: Gsdpfx Aeuxfucsdteil - External and internal profile grinding with straight wheel Thread grinding software: - Single and multi-start external and internal thread grinding with threads dressed on the wheel. Dressing of single and multi-groove wheels. Flank angle freely selectable. Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-circular plunge grinding: - External and internal non-circular oscillation grinding Non-circular grinding software: Non-circular grinding requires the workpiece axis to be equipped with a high-resolution rotary encoder to operate the axis as a C-axis. The non-circular...

Kondisi: bekas, TECHNICAL DATA - Number of Axes: 3 - Centre Height: 175 mm - Distance Between Centres: 1000 mm LINEAR AXES - Grinding Length: 500 mm - Travel X x Z: 267 x 650 mm GRINDING SPINDLE HEADSTOCK - Continuous Orientation: +/-8.5° - External Grinding Wheel Dimensions: 500 x 80 x 203 mm - Grinding Wheel Holder Spindle Headstock Power: 7.5 kW - Cutting Speed: 44 m/s WORKPIECE SPINDLE HEADSTOCK - Taper Type: MT5 Gedpfouhbydsx Adtjil - C-Axis: +/-0.5° - Power: 1 kW - Rotational Speed: 30–1,000 rpm TAILSTOCK - Taper Type: MT3 - Quill Stroke: 35 mm - Quill Diameter: 50 mm - Max. Workpiece Weight Between Centres: 130 kg ELECTRICAL SUPPLY - Supply Voltage: 400V 50 Hz - Machine Dimensions: 2700 x 2350 x H. 2100 mm - Weight: 4,000 kg OPERATING HOURS - Operating Hours: 17,775 h ACCESSORIES - CNC FANUC 16i-TA Control - Pictogramming - Studer RELEASE C - Remote Control with Electronic Handwheel - SENSITRON - Hydrobalance HBA 40000-1 Dynamic Balancing Device - MOVOMATIC C25 Automatic Length Probing Arm - MOVOMATIC In-process External Diameter Measuring Arm - Grinding Wheel Guard with Automatic Tilting - Fixed Diamond Dressing Device on Workpiece Spindle Headstock - Coolant Tank: 375 l - Paper Filter - Oil Mist Extraction - Grinding Wheel Flange Holders