Gunting plat hidrolik + mesin bending ayun

LOTZE T 1000 / 5,5

Kondisi: diremajakan ulang (bekas), SCHLATTER MG24 Welded Wire Mesh Production Line Completely Refurbished WORKING RANGE Panel width: max. 2,500 mm Cross wire length: min. 900 mm Cross wire length with QF5 distributor: min. 300 – 1,600 mm Maximum spacing between outer longitudinal wires: 2,400 mm Mesh length (longitudinal wire length): max. 2,500 – 6,000 mm Minimum spacing between longitudinal wires: 100 mm Cross wire spacing: 25–250 mm Adjustable via cutting device (0–1) Longitudinal wire diameter: 4.0 – 12.0 mm Cross wire diameter: 4.0 – 12.0 mm Maximum number of longitudinal wires: 24 MG 24.1/8C MESH WELDING MACHINE – Basic configuration including: - 1 Machine base frame - 1 Upper support for reception of press units, continuously adjustable by handwheel - 1 Magnetic support unit with holding magnets and cross wire monitoring - 1 Row of pneumatic solenoid valves for operation of the press units - 1 Air and water installation - 2 Pneumatic rotary drives with oil damping - Static torque with 5 bar compressed air: 480 Nm - Continuously adjustable front section: 25 – 250 mm, adjustable via cutting device (0–1) - 1 Feed trolley with panel lifting device - 1 Tool kit for machine adjustment WELDING SECTION including: 8 Type C transformers Rated power per transformer: 100 kVA Secondary open-circuit voltage: 7.1 V Rated secondary current: 14 kA 8 ES 130 thyristor contactors 12 Welding presses: 5.0 kN 12 Longitudinal wire current bridges for wire spacing: 50–100 mm 12 Longitudinal wire current bridges for staggered wires: 100 mm 10 Longitudinal wire current bridges for wire spacing: 100–150 mm 8 Longitudinal wire current bridges for staggered wires: 150 mm 6 Longitudinal wire current bridges for wire spacing: 150–200 mm 6 Longitudinal wire current bridges for staggered wires: 200 mm 24 Bottom copper electrode holders with standard angled electrodes, each with a water-cooled current cable, width: 58 mm Nkodpfewu Tu Dsx Ahwju 24 Wire clamping jaws Panel width: max. 2,500 mm Cross wire length: min. 900 mm Cross wire length with QF5 dispenser: min. 300 – 1,600 mm Max. spacing between outer longitudinal wires: 2,400 mm Mesh length (longitudinal wire length): max. 2,500 – 6,000 mm Min. spacing between longitudinal wires: 100 mm Cross wire spacing: 25–250 mm Longitudinal wire diameter: 4.0 – 12.0 mm Cross wire diameter: 4.0 – 12.0 mm Max. number of longitudinal wires: 24

Kondisi: baru, penahan belakang: 750 mm, - Capacity 1050 x 6 mm - NC electric back gauge Nedpfegg N Hbex Ahwsku - Foot switch - Rear photoelectric safety guard - Support arms - Cutting line illumination - Brake motor - Emergency stop - Documentation - Weight 1800 kg - 400V

Kondisi: bekas, Tahun pembuatan: 2015, nomor mesin/kendaraan: A2536805, Pressure: 40 t Nkedpfx Asfxyhfjhwou Stroke: 250 mm Retracting Force: 6.3 t Motor: 5.5 kW Max. Working Height: 450 mm Max. Approach Speed: 90 mm/sec Pressing Speed: 10 mm/sec Travel Distance (w): 250 mm Ram Plate: 500 x 200 mm Table Plate: 600 x 650 mm with T-slots Table Cut-out: 200 x 170 mm Table Height: 850 mm Oil Tank: 200 l The described machine can be custom-built for you. Production time is approximately 5 months from receipt of payment. Approach: The press moves to the zero point at up to 90 mm/second. The positioning accuracy is 0.5 mm or better. Return: The press moves back to the end point at up to 90 mm/second. The accuracy here is 0.5 mm or better. The dwell time is adjustable from 0 to 10 seconds (in increments of 0.1 seconds). The press force can be adjusted between 10 and 40 tons (in bar). Further control details: The control system can be locked with a key switch. The key switch for the control system has the following functions: - Manual operation via two-hand control at 9.5 mm/sec in setup mode. (Stops at any desired position when the switches are released.) - Manual operation for bending tasks at up to 9.5 mm/sec using two-hand control and automatic return to top dead center when both two-hand buttons are released. - Automatic operation with secure tooling at up to 200 mm/sec. This function is labeled with a warning on the control panel. In automatic mode, the machine may only be used with fully enclosed, secure tooling—this information is clearly displayed on the front of the machine. In manual setup mode, the machine can also be operated via the two-hand control at a maximum of 9.5 mm/sec. Bending operations can also be performed in setup mode. A key selector switch is used to toggle between automatic and manual operation. Position adjustment for top and bottom dead center as well as switching position for speed reduction is managed via sensors that are adjustable on a chrome-plated rod. A clamping thread allows for fine sensor adjustment—accuracy is +/- 0.5 mm. The press can be equipped with a bending blade and, using the two-hand control, can perform sheet metal bending as well as punching, notching, and bending in automatic mode with secure tooling.

Kondisi: baik (bekas), Fungsionalitas: berfungsi sepenuhnya, tahun perombakan terakhir: 2023, For sale: a complete and fully operational steel sheet roll forming line, suitable for processing coil materials such as Magnelis into any desired profiles, such as C-profiles commonly used in photovoltaic installations and farms, steel hall construction, shelters, as well as for furniture manufacturing, etc. The line, including an uncoiler, is installed in a heated hall under near-laboratory conditions. Prospective buyers can arrange for a test run prior to purchase. I have contacts to suppliers of profiling roll sets for specific profiles, as well as to companies specializing in machine upgrades and expansions. Further information strictly by phone only – I do not respond to written messages. A VAT invoice will be issued for the production line. Nedeu A U Utopfx Ahwoku Location: Poland, near the Ukrainian border (city: Krosno).

Tahun pembuatan: 2015, Kondisi: bekas, Dijual Lini Produksi Profil W dan C Dirancang untuk produksi guardrail jalan, tiang, dan elemen pengikat. Lini lengkap ini cocok untuk produksi industri secara terus-menerus. Lini terdiri dari: - Dua unit dekoiler - Lini produksi tiang - Lini produksi parapet - Dua mesin press untuk membuat elemen pengikat Spesifikasi teknis: - Panjang: 17 m - Lebar: 1 m - Tinggi: 1 m - Daya motor: 22 kW - Berat: 18 t - Tahun produksi: 2015 - Produsen: Chengxing Machinery (Cina) Tujuan dan keunggulan: Lini produksi profil W dan C ini dirancang untuk memproduksi berbagai elemen keselamatan jalan: guardrail terpisah, tiang pendukung, dan elemen pengikat. Peralatan memberikan proses produksi yang andal, stabil, dan berkesinambungan. Perangkat siap untuk inspeksi. Nkedpfsxhf R Iex Ahweu Jangan ragu menghubungi kami jika ada pertanyaan lebih lanjut.

Kondisi: baru, Tahun pembuatan: 2023, jangkauan lengan: 1.400 mm, kapasitas angkut: 6 kg, New TIG Welding Robot OKIO AB6-C1400 -Country of origin: China -Type: AB6-C1400 -Number of axes: 6 -Reach: 1400 mm -Maximum payload: 6 kg Nsdpfxeqnt N Dj Ahweku -Control cabinet -Remote control -Wire feeder -Welding power source: TIG WSM400R -Cooler

Tahun pembuatan: 1990, Kondisi: bekas, nomor mesin/kendaraan: 9072492, Rated power: 100 kVA Throat depth: 500 mm Electrode arm distance: 330 - 500 mm electrical connection: 400 V kW Dimensions (L x W x H): 700 x 1420 x 2000 mm Nsdpfx Asz H Dyshwjku Weight: 750 kg

Tahun pembuatan: 1978, Kondisi: sangat baik (bekas), Technische Daten: -Hersteller: DRAWEBA -Modell: DDANS 17 l Nkjdpfxelf Iqne Ahwsu -Baujahr: 1978 -Drahtdurchmesser: 1,4 - 1,6 mm -Maschenweite (min.): 10 x 10 mm -Netzbreite: 1600 mm

Tahun pembuatan: 2010, Kondisi: siap digunakan (bekas), Electrode force: 100 daN, welding power: 255 kVA, rated power: 80 kVA, with DALEX DRF 5.2 cooling system. Njdpfeiknv Eox Ahweku

Tahun pembuatan: 2004, Kondisi: baik (bekas), nomor mesin/kendaraan: 0441057, Offer 23300 Technical Specifications: - Abrasive belt dimensions: 75 x 2000 mm - Surface grinding opening: 75 x 300 mm - Adjustable-angle support vise: 90° to 30° - Belt speed: 15 + 30 m/sec - Possible contact wheel diameters: 20 - 76 mm Nksdpfx Ajpug D Eshweu - Contact wheel length: 75 mm - Drive: 400 V / 2.2 / 3 kW - Drive speeds: 1440 / 2880 rpm - 1 piece contact wheel: 48 mm - Required floor space (approx.): W 800 x H 1000 x D 1300 mm - Weight (approx.): 250 kg