Mesin cetak tiup peregangan Sidel SBO 6/10

SIDEL SBO 6/10

Sidel stretch blow molding machine
Max. output: 6,000 bottles/hour.
Max. bottle size: 3,000 cc.
Blow stations: 6.

The machine is in very good condition and well-maintained.

GENERAL INFORMATION
The SBO 6/10 features 6 molds and 10 heating modules. It is compatible with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel’s two-stage PET stretch blow molding machines require previously produced preforms to be fed into the machine. Separating the processes of bottle and preform production allows for optimized production, increased operational flexibility, and provides higher productivity and yield.

MAXIMUM PREFORM DIMENSIONS
Neck height: 9–41 mm (measured from the bottom edge of the support ring)
Minimum internal neck diameter: 19 mm
Maximum external neck diameter: 34 mm
Preform support ring diameter: 29–51 mm
Maximum preform length: 210 mm

MAXIMUM BOTTLE DIMENSIONS
Maximum bottle diameter: 130 mm
Maximum bottle height: 380 mm
Bottle volume: 0.25 – 3 liters

AVERAGE PREFORM WEIGHTS (for still and carbonated beverages)
0.25 liter bottle: 14–20 grams
0.50 liter bottle: 20–33 grams
1.00 liter bottle: 26–40 grams
1.50 liter bottle: 35–51 grams
2.00 liter bottle: 44–58 grams
3.00 liter bottle: 68–84 grams

BLOW WHEEL
Height: 3.5 meters
Number of molds: 6
Clamping force: 10 tons
Article height (below the neck) at outlet: approx. 1.4 meters
Machine DC drive motor power: 4 kW

Ibodpfx Asg Ailcoltsb
HEATING CONDITIONER
Height: 2 meters
Number of oven heaters: 10
Number of heating zones per unit: 8
Maximum power: 170 kW

ELECTRICAL USAGE
Maximum supplied power: 200 kW
Average consumption: 100–150 kW/h (varies depending on bottle produced)

COMPRESSED AIR
Supply pressure: 7–35 bar
Operating pressure: 7 bar
Flow rate: 50–100 Nm3/h (varies depending on bottle produced)
Blowing pressure – champagne base: up to 25 bar
Blowing flow – champagne base: 110–550 Nm3/h
Blowing pressure – petaloid base: up to 35 bar
Blowing flow – petaloid base: 155–770 Nm3/h

COOLING WATER
Temperature: 10–12°C
Pressure: 5–6 bar
Flow rate: up to 6 cubic meters/hour
Up to 16,000 Kcal/hour heat to be removed

WEIGHT
Blow wheel with molds: 8 tons
Heating conditioner: 2.2 tons
Preform feeder: 0.65 tons
Control cabinet: 0.85 tons

PREFORM HEATING CONDITIONING
The preforms are conveyed to the heating conditioning unit with the necks facing upwards. This unit continuously ensures that the preforms are inverted before being presented neck-down in front of the heating modules, and then inverted again. During the heating phase, the preforms are rotated and their necks are protected from heat to optimize temperature distribution without deforming the neck. Heating is achieved through 10 heating modules. Each unit can accommodate up to 8 horizontally arranged infrared lamps, which are air-cooled at the ends. The heating output of 8 zones, corresponding to the 8 lamp rows, is adjustable to optimize the heat profile. These zones are regulated on all SBO models. After heating, preform temperature is monitored by an infrared camera to regulate the controlled zones, ensuring the maintenance of the required temperature.

Iklan ini diterjemahkan secara otomatis. Kesalahan terjemahan mungkin terjadi.