Beli Hydraulic double-column presses & four-column presses bekas (313)

Kondisi: bekas, Tahun pembuatan: 1995, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 250 t, lebar meja: 1.600 mm, panjang meja: 2.650 mm, berat keseluruhan: 55.000 kg, langkah bantalan cetakan: 235 mm, Hydraulic deep-drawing press, manufacturer Wanzke, model GTA 250 Year of manufacture: 1995, used Technical Specifications: Pressing force: 2,500 kN Ram stroke: 600 mm Ram speed, working stroke: 25 mm/s Blankholder force: 1,600 kN Csdpfjup Skwsx Aarohf Blankholder stroke: 235 mm Table clamping area: 2,650 x 1,600 mm Stroke limiting spindles: 2 pcs. Damping cylinders: 2 pcs. Drive power: 75 kW Dimensions (approx.): width 4,250 mm (without cladding), depth 2,000 mm, height 5,150 mm Weight: 55 t Table: Drill holes for locating pins in the center of the press table. From there, additional holes are spaced 150 mm to the right and left. A central hole is also present along the width of the press table. Here too, the hole spacing is 150 mm. A maximum of 15 locating pins in the longitudinal direction and 7 in the width is possible. Locating pin diameter: 30 mm

Kondisi: bekas, Tahun pembuatan: 2021, nomor mesin/kendaraan: HB 2022-A-073, Portal frame press with 300 T capacity a) Idle and pressing speed up to 17 mm/sec Cedpfjh Agnujx Aarshf b) Opening speed up to 55 mm/sec c) Table size 2500x1600 mm d) Open height 700 mm e) Overall dimensions approx. LxWxH 4500x2300x3700 mm f) Oil temperature display on the tank g) Lubrication via grease nipples h) Table in grid construction, with T-slots as per customer specification, otherwise 22 mm i) Operation via swivel arm, mounted on the bridge j) Pressure adjustment from 50 T to 300 T via MONITOR k) Bridge traverses by two gear motors, via rack and pinion l) Cylinder traverses left and right via rack and pinion m) Machine body double painted n) Cylinder induction-hardened Design Type of press: GANTRY PRESS Thermally neutral 80 – 120 °C Number of operating sides: 3 sides Forces Max. pressing force: 3,000 kN Max. free peeling force: 500 kN Pressure build-up time closed tool steel on steel: Max. 3 sec Dimensions Max. opening 700 mm Stroke and min. opening: 700 mm/0 mm Table height above floor approx. 980 mm Height above floor (overall height) approx. 3700 mm Minimum hall height: 5,000 mm Deflection Measured at max. closing force with 70% occupancy

Kondisi: bekas, Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: 71737, panjang total: 1.575 mm, lebar total: 640 mm, tinggi total: 1.970 mm, berat keseluruhan: 645 kg, tegangan masuk: 3.000 V, gaya penekanan: 40 t, kecepatan penekanan: 5 mm/dtk, de37078f-b35f-45e5-8465-d69e6e788fea Chodowbz Irepfx Aaref

Kondisi: bekas, Pressing force 400 kN, table 450x560 mm, ram 375x300 mm, distance table to ram 340 mm, stroke 160 mm, through-hole diameter 100 mm, lateral column passage 220x410 mm. Cjdpfx Aaeum Uuyorshf

Kondisi: baru, Tahun pembuatan: 2025, Fungsionalitas: berfungsi sepenuhnya, Specialised press designed from the ground up for briquetting iron, steel, and similar alloys. Equipped with integrated oil collection mats. Packaging table not included – only briquette guides (rails) are provided. Features clear bunker doors and oil heating elements as standard. The machines are operated via Siemens KTP-400 touchscreens. 2nd generation available for purchase from February 2024. For this press, please contact us first! Technical Data: Throughput: Up to 600 briquettes/hour* Main motor: 30 kW Feed motors: 2.6 kW Cedetmugcepfx Aarshf Cooling system: 1.6 kW Total connected load: 34.2 kW Oil tank: 260 litres Filters: 4 Length: 2,000 mm Width: 2,000 mm Height: 2,200 mm Weight: 3,500 kg Briquette size: 40–110, D80 mm Warranty: 2 years / 2,000 operating hours

Kondisi: hampir baru (bekas), Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: MV-250E/NC, gaya penekanan: 250 t, lebar meja: 2.500 mm, panjang meja: 1.150 mm, Perlengkapan: dokumentasi / manual, penghadang cahaya keselamatan, HYDRAULIC FOUR-COLUMN PRESS FOR DEEP DRAWING APPLICATIONS TECHNICAL DATA Press Force / Main Cylinder: 250 t Cushion Force: 50 t Motor Power: 11 kW Ram Stroke: 500 mm Approach Speed: 80 mm/s Working Speed: 7 mm/s Return Speed: 105 mm/s Column Diameter: 150 mm Chodpswkuchsfx Aarsf Maximum Pressure: 260 bar Usable Table Area: 2,500 x 1,150 mm Column Spacing: 2,500 x 700 mm Maximum Open Height: 1,000 mm Cushion Size: 950 x 750 mm Working Height: 1,100 mm Overall Height: 3,650 mm Weight: 15,000 kg DESCRIPTION The hydraulic four-column press MV-250E/NC belongs to the M/NC series and was specially developed for enhanced precision and capacity, particularly in deep drawing operations. It is equipped with upper and lower tables made of C45E steel, featuring DIN-650 T-slots for minimal friction during the vertical movement of the upper table. This is ensured by maintenance-free bimetallic bushings and perfect parallel alignment via four chrome-plated, ground cylindrical columns. The press employs an optimized hydraulic system operating at less than 290 bar to ensure long service life and reliable performance. All essential safety and health requirements are met in accordance with CE regulations. CONSTRUCTION AND TABLES • Three electro-welded blocks made exclusively from S355JR steel. • Stabilized and machined post-welding to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • The lower table is fitted with a 50-ton hydraulic cushion (usable area: 950 x 750 mm) and three front supports for handling tooling outside the press. • Includes a SIEMENS KTP-400 NC for controlling the ram stroke, speed changes, and cushion adjustment. • Integrated SIEMENS S-7 PLC supporting programming of up to 99 memory settings. CYLINDER AND HYDRAULIC UNIT • Single-acting cylinder with honed sleeve, chrome-plated piston, and wear-resistant guides. • The entire hydraulic unit is installed on the top of the press. • Hydraulic group comprises a low-noise Denison hydraulic pump and an air-oil cooler. • Includes: - Decompression system - Solenoid pressure valves - Pre-fill valves - Communication valve - Check valve - Pressure relief valve - Safety valve (fall-arrest). ELECTRICAL INSTALLATION AND SAFETY • Features a SIEMENS SIMATIC S7-1200 safety PLC and KTP-400 4-inch touchscreen on the control panel. Allows programming of semi-automatic/automatic cycles, power, stroke, and dwell time, with memory for up to 99 recipes – each capable of storing all main parameters. • The electrical control panel is equipped with a selector switch to choose work mode: manual “setup” or automatic cycle “production.” • Machine operation via low voltage electric foot pedals. • For safety: Category IV light barriers at the front working area, two fixed side guards, and a rear safety guard equipped with a magnetic separation detector.

Kondisi: bekas, Tahun pembuatan: 1992, Fungsionalitas: berfungsi sepenuhnya, tinggi pemasangan: 700 mm, gaya penekanan: 250 t, lebar meja: 1.250 mm, panjang meja: 1.150 mm, langkah bantalan cetakan: 150 mm, panjang langkah: 400 mm, Hydraulic Double Column Press DUNKES HDS 250/10 Year of manufacture: 1992 Technical specifications: Press force at 260 bar: 250 t Rapid approach speed: 365 mm/s Table clamping area approx.: 1150 x 1250 mm Ram clamping area approx.: 1150 x 1250 mm Blankholder cushion area approx.: 800 x 1000 mm Blankholder cushion force (200 bar): 100 t Blankholder cushion stroke: 150 mm Chjdeup Si Hjpfx Aarjf Power requirement: 45 kW Installation height: 700 mm Ram stroke: 400 mm Control system converted to SIEMENS (in 2005) Machine height approx. 5,400 mm TP language currently Polish

Kondisi: hampir baru (bekas), Tahun pembuatan: 2023, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 40 t, lebar meja: 1.500 mm, panjang meja: 1.000 mm, kecepatan mundur: 10 mm/dtk, lebar pelat tuas: 1.500 mm, panjang pelat penekan: 1.000 mm, jenis arus masuk: AC (pendingin udara), jarak pergerakan sumbu X: 1.200 mm, daya: 9 kW (12,24 hp), Perlengkapan: penghadang cahaya keselamatan, If the press does not exactly meet your requirements, please request a customized offer tailored precisely to your specifications with just one click: HIDROBRASIL manufactures presses exactly according to your needs at surprisingly competitive prices! ##### Die Opening and Closing Press with 40 Tons Press Force Table and Ram Size: 1500 x 1000 mm for heated tools Technical Data: Press force: 40 tons Maximum open height: 1800 mm Ram stroke: 1500 mm Oil temperature monitoring: Electric air cooling Lubrication: Manual via grease nipples Stroke length of the extending table: 1200 mm Speed of extending table: 30 mm/sec electrically, steplessly rotatable ram: Up to 180 degrees T-slots: As per customer specification Pressure adjustment: From 10 tons up to 40 tons Monitor: 10'' fitted to control cabinet for pressure setting and warning notifications Two-hand operation Special Features: Insulation of clamping plates towards ram: Using resin insulation plates and special ventilation plates Hydraulic system: Equipped with BOSCH REXROTH, PARKER, ATOS components Safety components: SICK Control system: SIEMENS Remote maintenance unit: SECOMEA - Ethernet Installation and Operation Conditions: Cjdpotwmp Sefx Aarshf Maximum ambient temperature: 40 °C Height above floor (overall height): Approx. 3800 mm Total weight of the press without operating fluids: Approx. 13 tons This machine is supplied in the customer’s desired colors and complies with all legal requirements and EU standards. ##### Are you looking for a perfectly matched machine? Contact us for a customized offer.

Kondisi: bekas, Double-column hydraulic press SMG Type HBP 200 - 2000 / 2000 Serial No. 7.4117 Year of manufacture: 1986 - Refurbished in 2000 Pressing force: 200 tons Chjdpfx Aasdzp Tcorof Distance between uprights (front): 2050 mm Clearance between uprights (lateral): 2030 mm Table size: 2800 x 2000 mm Ram area: 2000 x 2000 mm Ram stroke: 700 mm Maximum installation height: 1850 mm Table height above floor: 750 mm Ram return force: 33 tons Rapid advance speed: 500 mm/s Pressing speed: 72/36 mm/s Return speed: 420 mm/s Safety distance: 230 mm Main motor power: 75 kW Control pump motor power: 11 kW Power supply: 380 Volt, 50 Hz - 8-way flat guide for ram - Clamping plate with 22 mm T-slots on ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking in top dead center - Travel measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS PLC S7 - Free-standing control cabinet - Two-hand control console, free-standing - Ground-level installation - Central lubrication system - Operating manual with circuit diagrams Space requirement (upright): L x W x H 3700 x 2900 x 5900 mm Total machine height with motor: 5900 mm Space requirement for horizontal transport: L x W x H 5900 x 3250 x 2950 mm Weight: 38 tons The machine was used as a production press at Volkswagen until 2000. From 2000 onwards, the machine was used as a try-out press in a toolmaking facility. Good condition

Kondisi: sangat baik (bekas), Tahun pembuatan: 2004, Manufacturer: MULLER WEINGARDEN Model: G2-1400/630 Year: 2005 Condition: Used Stock number: 0362 STATE: EXCELLENT PRESS FORCE: 1400 tons SLIDE STROKE: 1,500 mm SLIDE WORKING SPEED: FROM 40 TO 127 mm/s APPROACHING SPEED: 700/850 mm/s TABLE DIMENSIONS: 3,500 x 2,500 mm FRONT OPENING: 3,500 mm BLANK HOLDER CUSHION FORCE (LOWER): 400 tons BLANK HOLDER CUSHION STROKE (LOWER): 300 mm SIDE OPENING: 2,400 mm WITHDRAWABLE TABLE: Side extraction available PRESS FORCE: 630 tons PRESS SLIDE STROKE: 1,300 mm PRESS TABLE DIMENSIONS: 3,350 x 2,130 mm PRESS FRONT OPENING: 3,350 mm PRESS SLIDE WORKING SPEED: 12 to 20 strokes per minute Chjdpfxew Hdpce Aaref PRESS SIDE OPENING: Side extraction available

Kondisi: baik (bekas), Tahun pembuatan: 1970, Pressing force 80 t Passage width 350 mm Stroke 600 mm Table dimensions - longitudinal 400 mm Chodpfxevwgqre Aarjf Space requirement approx. 1400 x 1050 x 2350 mm This press is still in very good condition and has seen little use.

Kondisi: bekas, Tahun pembuatan: 2021, Fungsionalitas: berfungsi sepenuhnya, tinggi total: 7.000 mm, lebar total: 4.750 mm, panjang total: 6.000 mm, gaya penekanan: 1.000 t, kecepatan mundur: 60 mm/dtk, We are offering a new build of the machine shown here. The machine was commissioned in 2021 and can be inspected at the customer’s site. Technical Data: - Force: tn 125 - 1000 - Opening Force: tn 100 - Driven Speeds: 1 - Motor Power: kW 75 - Fast Fill Speed: mm/s 100 - Variable Working Speed: mm/s 12-4 - Return Speed: mm/s 60 - Guide Diameter: mm 300 - Max. Pressure: Bar 290 - Usable Table Area: mm 4,750 x 2,200 - Lower Table Travel: mm 2,200 Cedpfxowpgwne Aarjhf - Vertical Movement of Upper Table: mm 800 - Between Columns: mm 5,000 x 1,490 - Total Front: mm 6,000 - Total Side: mm 4,750 - Total Height: mm 7,000 - Weight: kg 150,000 Specially designed for the setup of progressive compound dies. FRAME AND TABLES • The frame consists of autogenously cut steel and is divided into three electro-welded monoblocks, made exclusively of S355JR steel. • Stabilized and machined after welding to ensure perfect parallelism and accuracy. • Calculated and designed using finite element software. • Cylindrical columns with a 300 mm diameter, featuring high mechanical strength; ground and chrome-plated to ensure low friction and wear coefficients. • Upper table with T-slots and anti-fall safety system. • Usable table area: 4,750 x 2,250 mm. • Structure withstands 600 TN of concentrated force on one third of its surface. • The lower table is designed for a displacement of up to 50 TN and is supported by bronze guides with graphite inserts and mechanical positioning centers for precise table positioning. CYLINDER AND HYDRAULIC UNIT • 6 single-acting cylinders with lapped sleeves, chrome-plated pistons, and wear-resistant guides. • Four 50 TN hydraulic compensators mounted at the ends of the lower table. • 800-liter hydraulic power unit with low-noise Denison pump, automatic fast-fill shutdown, and equipped with a decompression system for working speed. • Proportional pressure system and optical measuring instruments for monitoring movement on the upper table, featuring a synchronous electronic system for compensation of eccentric or unbalanced forces. • Hydraulic unit cooling system with independent air-oil cooler. • All hydraulic presses in the M series are equipped with a lateral pressure switch to adjust the pressure to the requirements of the operation. • Glycerine pressure gauge with tonnage display. ELECTRICAL INSTALLATION AND SAFETY • Includes SIEMENS safety PLC SIMATIC S7 1200 and 12” touchscreen. Enables programming of semi-automatic and automatic operating modes, power, travel distance, and dwell time on the upper table. Up to 300 recipes can be stored, with each recipe able to program all the above values. • Low-voltage operation with two-hand control. • Anti-fall safety system with hydraulic safety jaws. • Light barriers (Level IV) at the front and rear. • Side safety guards with opening and safety micro-switches.

Kondisi: siap digunakan (bekas), Hydraulische Presse, Lagerpresse, Gebrauchtmaschine Hersteller: Stenhoj Hydraulic Chodpsu Hi Tlefx Aarjf Modell: 1T TE Presskraft: 1 Tonne Hub: 300 mm Maximaler Betriebsöldruck: 16,1 MPa Gesamtmaße: 700 x 1140 x 2220 mm Gewicht: 1000 kg Elektrische Anschlusswerte: 400V; 10A-20A Hydraulikdruck: 200 bar Einstellbare Presskraft

Kondisi: seperti baru (mesin pameran), Tahun pembuatan: 2020, Hydraulic 400-ton Four-Column Press Suitable for continuous multi-shift operation, with the following main features: a) Closing speed: 100 - 450 mm/sec b) Opening speed: 50 - 250 mm/sec (adjustable via touchscreen) c) Pressing speed: 5 - 60 mm/sec (adjustable via touchscreen) d) Piston accumulator with approx. 4 nitrogen cylinders e) Table size (clamping surface): 2700 x 1700 mm (viewed from the front, between the columns) f) Total table size: 3400 x 1700 mm g) 28 mm T-slots as per customer requirements h) Table, ram, and press head stress-relieved annealed i) Column diameter: 250 mm j) Ram size: 3400 x 1700 mm (clamping surface 2700 x 1700 mm) k) Machine overall size approx. 3900 x 2200 (footprint) x 5700 mm (height) l) Oil temperature monitoring (adjustable via touchscreen) m) Automatic lubrication (adjustable via touchscreen) n) Free positioning of the ram (adjustable via touchscreen) o) KEYENCE safety light curtains 14 mm front and rear p) Circulation oil cooling (adjustable via touchscreen) q) Pressure holding valve 0 to 600 sec. (adjustable via touchscreen) r) Table plate size 3400 x 1700 mm, precision milled s) Side doors with monitoring, 1200 mm high, 1000 mm wide t) RITTAL control cabinet, 2200 mm wide, can be positioned up to 20 m from the press u) Pressure settings from 50 tons to 400 tons (adjustable via touchscreen) v) Stroke limit selectable via pressure or position w) Modes: program operation, setup mode, single stroke + continuous stroke (selectable via rotary switch) x) Swivelling operator panel with 15-inch touchscreen monitor y) Two-hand operation on both sides z) Prepared for automatic material feed (SIEMENS S7 1500) aa) Machine body primed and painted bb) Assembly, commissioning and instruction available at extra charge Hydraulics: All press hydraulics are assembled exclusively with BOSCH-REXROTH / Parker / HAWE components. The control cabinet contains only components (SIEMENS) that are readily available in Germany. All safety devices apart from the light curtains are SICK brand. The controller supplied is SIEMENS (S7 1500), including the 15-inch touchscreen panel. The SIEMENS remote maintenance unit SECOME - Ethernet is included in the scope of delivery. SPECIAL FEATURE: Our double-ram design in combination with a piston accumulator allows full performance to be delivered using a single 90 kW main motor. Further technical details (section 1.3): Technical Data Design Press type: Four-column press Thermally neutral: 80 – 120 °C Number of operator sides: 2 Forces Pressing force max.: 4,000 kN Free opening force max.: 600 kN Pressure build-up time, tool closed (steel on steel): max. 2 sec. Dimensions Planned minimum tool height: 600 mm Max. opening: 1,600 mm Stroke and min. opening: 1,000/600 mm Table height above floor: 820 mm Overall height (build height): approx. 5,700 mm Minimum hall height: 7,000 mm Parallelism deviation at 20°C: +/- 0.1 mm Deflection Measured at max. closing force, 70% table occupancy: ≤ 0.17 mm/m Codpfxog Iihwe Aarjhf Weight Total weight of the press without operating fluids: approx. 52 t Speeds (see attached cycle diagram) Rapid closing: 100 – 450 mm/s Pressing speed at max. force ...

Kondisi: bekas, Machine not operational – control unit is not functioning Special offer price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Serial No. 300487 Year of manufacture: 2006 Pressing force 500 tons Distance between uprights (front/back): 2520 mm Table size: 2500 x 2500 mm Ram surface: 2500 x 2500 mm Ram stroke: 600 mm Max. installation height: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1,000 liters Ram retraction force: approx. 22 tons Adjustable approach speed: 100–800 mm/s Csdpfx Aasdzqptjrehf Pressure build-up to 5000 kN: approx. 0.7 sec Return speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-fold flat guideway for the ram - Hydraulic ram locking at top dead center - Free-standing control cabinet (200 x 50 cm) - Electrical control: SIEMENS PLC S7-314 - Operation via SIEMENS OP 170-B (5.7”) - Free-standing two-hand control panel - Floor-level installation - Table plate: 2510 x 2530 x 135 mm (approx. 6,700 kg) - Central lubrication - Operating manual with circuit diagrams Required space (L x W x H): 372 x 260 x 460 cm Space required for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition

Kondisi: bekas, Tahun pembuatan: 2020, Fungsionalitas: belum diuji, tinggi total: 6.400 mm, lebar total: 4.500 mm, panjang total: 3.800 mm, kecepatan operasi: 110 mm/dtk, kecepatan mundur: 180 mm/dtk, tabel jarak ke piston: 1.500 mm, We are offering a newly built machine of the type shown here. The machine was commissioned in 2020 and can be inspected at the customer’s site. Technical Data: - Pressing force: 800 tons - Opening force: 80 tons - Motor power: 55/75 + 55/75 kW - Ram stroke: 1,000 mm - Fast advance speed: 110 mm/s - Working speed: 6 mm/s - Return speed: 180 mm/s - Guide column diameter: 250 mm - Maximum pressure: 250 bar - Usable table area: 3,500 x 2,000 mm - Lower table travel: 2,000 mm - Distance between columns: 2,000 mm - Daylight opening: 1,500 mm - Total front width: 3,800 mm - Total side length: 4,500 mm - Overall height: 6,400 mm - Weight: 134,600 kg The MV-800E/NC-SINCRO press was specifically developed for the setting and testing of molds, dies, and stamps. The four columns, each with a diameter of 250 mm and made from C45E steel, are manufactured for heavy-duty applications. It features an optimized hydraulic system operating at up to 250 bar, ensuring long service life and reliability. The machine complies with all relevant safety and health requirements according to CE regulations. STRUCTURE AND TABLE Chodpswlrv Usfx Aarof • Frame designed to withstand 600 tons of concentrated force on 1/3 of its surface. • Lower table with T-slots. • Upper table with T-slots. • Usable table area: 3,000 x 2,000 mm. CYLINDER AND HYDRAULIC SYSTEM • Two double-acting hydraulic cylinders, each with 400 tons force. • Single-stage hydraulic power unit with automatic shut-off of advance speed and independent operation, equipped with a decompression system and proportional pressure pre-fill valves. Digital potentiometers on the upper table for displacement control and an electronic synchronizing system for compensation of off-center or unbalanced loads. • The press is equipped with a lateral pressure switch for optimal pressure adjustment for each job. • Glycerin pressure gauge with tonnage display. ELECTRICAL INSTALLATION AND SAFETY • Electrical system allowing operation with one or two main cylinder advance speeds. • The press offers both manual and automatic cycle modes (activated via a test selector switch): - Manual cycle allows step-by-step execution of all press movements at low speed. - Automatic cycle allows the press to run a complete production cycle. • Electrical safety system for upper table fall protection. • Lower table with hydraulic extraction and mechanical stops. • The machine is equipped with an operator panel featuring a touchscreen display for input of operating and calibration data. • 2 safety light curtains (category IV, 1,000 mm) installed at the front and rear. • Electrical components by Siemens, manufactured to IP55 protection class in accordance with applicable CE regulations and standards. • Electrical and hydraulic functions are redundant and self-monitored. Includes an additional safety block and self-check devices for operation and safety. Includes verification and certification of proper function and safety distance for light curtains. • Safety is ensured by a laser and area protection system with category IV light curtains.

Kondisi: seperti baru (mesin pameran), Tahun pembuatan: 2020, Double-column press, 20 t capacity Codpfxjhmbhqo Aarehf a) Closing speed up to 10 mm/s b) Opening speed up to 30 mm/s c) Table size (between columns): 1400 x 1100 mm d) Ram size (between columns): 1400 x 1100 mm e) Manual lubrication (via grease nipples) f) UKF Recirculating Cooling Filtration (electric cooling) g) Pressure adjustment from 4 t to 20 t (adjustable via rotary control) h) Stroke adjustment via sliding controller Design Press design: Double-column, hydraulic Thermal neutral zone: 80–120°C Number of operating sides: 1 side Forces Pressing force (max.): 200 kN Free tear-off force (max.): 20 kN Pressure build-up time (closed tool, steel on steel): Max. 4 s Dimensions Max. opening width: 500 mm Stroke: 300 mm Table height above floor: approx. 900 mm Overall height above floor: approx. 2800 mm Required hall height: min. 3,500 mm Parallelism deviation at 20°C: #ERROR! mm Deflection (measured at max. closing force with 2/3 load):

Kondisi: bekas, Double Column Hydraulic Press SCHÖN Type SH 25 Machine No.: 4453 Year of manufacture: 1999 Pressing force: 25 t Column spacing: 500 mm Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Table height above floor: 900 mm Motor power: 7.5 kW Connection: 380 Volt, 50 Hz Equipment: - SICK safety light curtain, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid traverse and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Press force regulation - Press dwell extension 1-10 s (pressure holding time) - Time setting for return stroke speed - Blowing device prepared electrically, without air valve - Hydraulic tool safety, manually adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1,200 kg Good condition Cedpfxsw A Amrs Aarjhf

Kondisi: hampir baru (bekas), Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: FDL-150-100E/NC, panjang total: 1.200 mm, gaya penekanan: 150 t, lebar meja: 800 mm, tinggi kerja: 600 mm, jarak antara tiang: 1.250 mm, Perlengkapan: dokumentasi / manual, penghadang cahaya keselamatan, HYDRAULIC DOUBLE-COLUMN PRESS WITH TWO LATERAL CYLINDERS FOR PRE-PRESSING AND PRESSING OF ROTORS AND STATORS, AND A CENTRAL CYLINDER FOR EXTRACTION OF THE MANDREL AND THE ROTOR SHAFT, AS WELL AS FOR SHAFT REMOVAL DURING REPAIR OPERATIONS Csdswpg Awspfx Aarjhf Equipped with a retractable table for stacking and handling rotors and stators. Complies with all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLES Comprises a rigid, electro-welded fixed-bed frame made exclusively of S355JR steel. Stabilized and machined at the end of the welding process to ensure perfect parallelism and accuracy. Calculated and designed with finite element software. Mechanically displaceable T-slotted table, 1200 x 800 mm, with a 1200 mm stroke, fitted with a worm gear reducer and 0.5 HP electric motor with brake. Central bore in the table of 250 mm diameter, maximum depth of 550 mm. Effective table lifting capacity for movement: 4 tonnes. Table displacement speed: 30 mm/sec. Internal front width: 1250 mm (distance between columns). Working height: 600 mm. 2 hydraulic cylinders, each with 75 tonnes of force (150 tonnes total), 1200 mm stroke, connected by a plate, with central bore of 250 mm diameter. Max. useful height from cylinder plate: 1,440 mm. Min. useful height from cylinder plate: 200 mm. EXTRACTION CYLINDER 1 central cylinder of 100 tonnes force, 1200 mm stroke. Adapted for fitting an extraction gripper, piston rod end threaded to M35x1.50, 40 mm length. Max. useful height of extraction cylinder: 1600 mm (to base of the rod thread). Min. useful height of extraction cylinder: 400 mm (to base of the rod thread). HYDRAULIC UNIT Dual-speed hydraulic unit, 5.5 HP “Siemens Motor”, with automatic cutoff for high speed and independent speeds. Max. pressure 250 bar. Pressure regulation system via proportional valves. Air-oil cooler. Temperature sensor. Hydraulic unit located on the right side. Includes a SIEMENS SIMATIC S7 1200 safety PLC and a 12" HMI touch display (MTP model) with 99 memory slots, allowing control over pre-pressing force, pressing force, fitting, and stroke for the pressing and extraction cylinders, as well as dwell times during processes. Electric and hydraulic controls are redundant and self-monitored. An additional safety block and self-monitoring devices are integrated for control and safety. Includes verification and certification of correct operation and safety distance for light curtains. Operation is performed via a low-voltage two-hand safety pushbutton. All installed electrical components are by Siemens (relays, contactors, main motor, etc.). Prepared for Industry 4.0. For safety, category IV photoelectric safety barriers are installed at the front work area, with two fixed side guards and a rear lockable guard with a magnetic disconnect detector.

Kondisi: hampir baru (bekas), Tahun pembuatan: 2019, Pressure: 400 t Stroke: 900 mm Table size: 1200 x 1200 mm Drawing cushion: 150 t Drawing cushion stroke: 280 mm Shut height: 1100 mm Chsdpfx Aaefh Izmjrsf

Kondisi: bekas, Tahun pembuatan: 2024, Fungsionalitas: berfungsi sepenuhnya, tinggi total: 2.675 mm, tinggi meja: 900 mm, lebar total: 1.075 mm, panjang total: 1.525 mm, gaya penekanan: 100 t, lebar meja: 700 mm, panjang meja: 500 mm, berat keseluruhan: 2.540 kg, kecepatan mundur: 60 mm/dtk, jarak antara dudukan samping: 800 mm, panjang langkah: 250 mm, Perlengkapan: penghadang cahaya keselamatan, RIGID FRAME HYDRAULIC PRESSES We have designed the motorized rigid frame hydraulic presses of the R/NC series with a range of six different capacities, from 80 to 500 tons. Specifically engineered for stamping, die cutting, and deep drawing applications. The next-generation R series hydraulic presses have evolved to offer versatile capabilities, including integration into automated production lines. They operate at hydraulic pressures below 320 BAR to ensure greater longevity of the entire hydraulic system. The R/NC series deep drawing and stamping presses feature an electro-welded frame constructed exclusively from S355JR steel. The frame is stabilized and machined after welding to ensure perfect parallelism and precision. All structural calculations and designs are carried out using finite element analysis software. This enables us to consistently guarantee our high standards of precision and quality. The presses are equipped with an upper and lower table manufactured from precision-machined C45E steel, both featuring DIN-650 T-slots. The upper table’s perfect parallelism is maintained by four lateral cylindrical guides fitted with maintenance-free, bimetal, low-friction bushings. Double-acting cylinder with honed barrel, chrome-plated piston rod, and maintenance-free wear guides. Codpfxewlgkmj Aarjhf Two-speed motorized hydraulic unit with automatic disengagement of high speed. Includes cylinder decompression valve. Standard equipment includes a SIEMENS SIMATIC S7 1200 safety PLC and a 4” MTP-400 touchscreen located above the electric foot pedal. This system allows programming of semi-automatic and automatic operation modes, force, stroke, and dwell time for the upper cylinder. The control can store up to 99 recipes, with all process parameters programmable per recipe. The electrical panel features a selector switch for manual or automatic operation and a keyed selector for maintenance tasks. All hydraulic and electrical safety circuits are redundant and self-monitored. The system features an additional safety block and self-monitoring devices for control and safety functions. Includes verification and certification of correct operation and safety distances for the light curtains. To ensure safety, the machines are equipped with Type 4 PLe safety light curtains at the front working area, two fixed lateral guards, and a rear hinged guard with a magnetic interlock and polycarbonate windows, plus internal LED lighting. A hydraulic cushion or ejector can be installed as an option. Fully compliant with all essential health and safety requirements as per CE regulations. Each machine is supplied with an instruction manual. Force: 100 T Motor power: 13 kW Working speed: 3-9 mm/s Approach speed: 40 mm/s Return speed: 60 mm/s Maximum pressure (up to 320 bar): 319 bar Ram stroke: 250 mm Guide diameter: 50 mm Lower table dimensions: 700×500 mm Upper table dimensions: 600×450 mm Max. vertical clearance: 500 mm Front opening: 800 mm Working height: 900 mm Overall width (front): 1,525 mm Overall depth: 1,075 mm Overall height: 2,675 mm Weight: 2,540 kg

Kondisi: bekas, Tahun pembuatan: 2021, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 500 t, Hydraulic 500 T Gantry Straightening Press with tool clamping device and parallel alignment for bending blade a) Idle and pressing speed up to 17 mm/sec b) Opening speed up to 44 mm/sec c) Table size 2000x850mm d) Open height 1500 mm e) Overall dimensions approx. LxWxH: 1500 x 3000 x 4300 mm f) Oil temperature indicator on tank g) Lubrication via grease nipples h) Table with grid construction i) Remote control j) Pressure adjustable from 80 T up to 500 T via rotary knob k) Table extends hydraulically by 700 mm outward for loading l) Cylinder traverses left and right via rack and pinion m) Machine frame powder-coated or double-painted n) T-slots to customer specification o) Cylinder induction-hardened p) Installation, commissioning, and operator training available at extra cost Press type: GANTRY PRESS Thermal neutral zone: 80 – 120°C Number of operating sides: 3 sides Forces Max. pressing force: 5,000 kN Max. free tearing force: 800 kN Pressure build-up time (closed tool, steel on steel): Max. 3 sec Dimensions Cedpfxjwgakvo Aarohf Max. opening width: 1500 mm Stroke and min. opening: 1300 mm / 200 mm Table height above floor: approx. 850 mm Total height above floor (installation height): approx. 4,300 mm Minimum hall height: 5,000 mm Deflection Measured at max. closing force with 70% load:

Kondisi: hampir baru (bekas), Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: MV-600E/NC, gaya penekanan: 600 t, lebar meja: 990 mm, panjang meja: 890 mm, kecepatan operasi: 5 mm/dtk, berat keseluruhan: 23.000 kg, kecepatan mundur: 18 mm/dtk, Perlengkapan: dokumentasi / manual, penghadang cahaya keselamatan, HYDRAULIC FOUR-COLUMN PRESS FOR PUNCHING, DRAWING, PIERCING AND DEBURRING OPERATIONS Pressing force ton 600 Motor power 40 HP at 440 Vac / 60hz Working speed mm/s 5 Approach speed mm/s 15 Return speed mm/s 18 Ram stroke mm 1,015 mm - (40") Codpfxewpggij Aarohf Guide column diameter mm 200 Usable table surface mm 990 x 890 x 130 (39" x 35" x 5") Clearance between columns mm 990 x 370 Vertical daylight mm 1,625 - (64") Working height mm 990 - (39") Lower hydraulic knockout ton 80 Lower knockout stroke mm 406.4 - (16") Upper hydraulic knockout ton 80 Upper knockout stroke mm 406.4 - (16") Total width (front) mm 1,850 Total length (side) mm 1,700 Total height mm 4,500 Weight kg 23,000 kg approx. The MV-600E/NC Four-Column Hydraulic Press belongs to the M/NC series and has been specifically developed for greater precision and capacity, designed for punching, deep drawing, stamping, and deburring tasks. CONSTRUCTION AND TABLE • Composed of three electro-welded blocks manufactured exclusively from S355JR steel. • Stabilized and machined after welding to ensure perfect parallelism and precision. • Calculated and designed using finite element analysis software. • Equipped with a SIEMENS SIMATIC S7 1200 PLC and a 7" HMI KTP-700 touch panel. This allows programming of force, ram stroke, and speeds, with storage for up to 300 different work cycles. CYLINDER AND HYDRAULIC SYSTEM • Double-acting cylinder with honed barrel, hard-chromed piston, and maintenance-free wear guides. • Motorized hydraulic unit with two speeds and automatic shut-off of fast speed. High-pressure pump and 10-micron return filter. Includes cylinder decompression valve, directional valve, and safety valve. A side-mounted pressure switch allows adjustment of optimal working pressure. • Glycerine-filled tonnage gauge. ELECTRICAL INSTALLATION AND SAFETY • The control panel includes a selector switch for manual, semi-automatic, or automatic operation, as well as a selector for choosing fast or slow speed. • Equipped with PLC for internal coordination of operations and decompression times. • Operation via low-voltage two-hand control station. • Electrical and hydraulic controls are redundant and self-monitoring, with an additional safety block and self-check devices for movements and safety. Includes inspection and certification of correct function and safety distances for light curtains. • Safety measures include Category IV light curtains in the front working area, two fixed side guards, and a rear movable guard with a magnetic interlock switch. • Fitted with IXON system for online connectivity in case of faults or reprogramming needs. • Ladder with upper walkway for maintenance access (scaffold).

Kondisi: hampir baru (bekas), Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: MV-300E/NC, tinggi total: 3.500 mm, lebar total: 1.800 mm, panjang total: 2.300 mm, gaya penekanan: 300 t, lebar meja: 1.250 mm, panjang meja: 1.250 mm, berat keseluruhan: 18.000 kg, tekanan: 320 batang, Perlengkapan: dokumentasi / manual, penghadang cahaya keselamatan, PRENSA HIDRÁULICA DE CUATRO COLUMNAS PARA TRABAJOS DE ESTAMPACIÓN, EMBUTICIÓN, TROQUELADO Y DESBARBADO Codpswphhnjfx Aarshf

Kondisi: bekas, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 150 t, tekanan: 250 batang, Hydraulic double-column press equipped with two lateral cylinders connected by a platen for pre-pressing and pressing of rotors and stators, and a central cylinder for mandrel extraction, rotor shaft fitting, as well as shaft removal for repair purposes. Features a retractable table for stacking and handling rotors and stators. MAIN CYLINDERS 150 TON - 2 hydraulic cylinders of 75 tons capacity each, with a stroke of 750 mm, connected by a slotted plate with a central bore of 250 mm diameter. - Maximum usable height between platen and cylinders: 1,300 mm. - Minimum usable height between platen and cylinders: 550 mm. EXTRACTION CYLINDER - 1 central cylinder of 80 tons capacity with a 1,200 mm stroke. - Prepared for attaching extraction clamp, rod end threaded to M35x1.5, 40 mm in length. - Maximum usable height cylinder extractor: 1,300 mm to the root of the rod thread. - Minimum usable height cylinder extractor: 100 mm to the root of the rod thread. TABLE & FRAME STRUCTURE - Mechanically movable slotted table, 1,200 x 800 mm, with a 600 mm travel, driven by a worm gear reducer with a 0.5 HP electric motor with brake. - Central bore on the table: 250 mm diameter, maximum depth 550 mm. - Effective lifting capacity for table movement: 4 ton. - Table movement speed: 2,600 mm/min. - Front inside width: 1,250 mm. - Working height: 600 mm. HYDRAULIC SYSTEM Chedpfoxc Ekdox Aarjf - Dual-speed hydraulic power unit, 5.5 HP capacity, with automatic disengagement of the rapid advance and independent speeds. Maximum pressure: 250 bar. - Digital maximum power regulation for pre-pressing, pressing, and fitting, digital tonnage display. Pressure regulation system using proportional valves. - Selector for approach and measuring speeds.