Turning automatic lathe

Citizen L 520-VII

Kondisi: bekas, TECHNICAL DATA - Number of spindles: 2 - Number of axes: 9 - Number of turrets: 2 MAIN SPINDLE - Spindle drive power: 6.7 / 10.7 [kW] - Spindle speed: 8,000 [rpm] - Max. bar diameter: 32 [mm] - Travel Z: 305 [mm] - Minimum C-axis resolution: 0.001 [degrees] SUB SPINDLE - Spindle drive power: 3.7 / 5.5 [kW] - Spindle speed: 6,400 [rpm] - Max. bar diameter: 30 [mm] Crsdpfeypxqrjx Aavji - Minimum C-axis resolution: 0.001 [degrees] - Travel X: 140 [mm] - Travel Z: 300 [mm] TURRET 1 - Number of positions: 10 - Number of live positions: 10 - Live tool speed: 12,000 [rpm] - Live tool power: 3.4 [kW] - Travel X/Z: 140/300 [mm] - Travel Y: -40/+25 [mm] TURRET 2 - Number of positions: 10 - Number of live positions: 10 - Live tool speed: 12,000 [rpm] - Live tool power: 3.4 [kW] - Travel X/Z: 140/320 [mm] - Travel Y: -25/+40 [mm] ELECTRICAL SUPPLY - Total connected load: 28 [kW] WEIGHT AND DIMENSIONS - Footprint: 3,870 x 1,670 [mm] - Machine height: 2,500 [mm] - Machine weight: 6,000 [kg] MACHINE HOURS - Powered hours: 23,240 [h] - Operating hours: 19,500 [h] EQUIPMENT - Control: Traub TX 8i-p - 3-color status lamp - Coolant tank: 500 [l] * with high-pressure pump: 3, 8, 20 [bar] * with paper filter - Chip conveyor - Parts catcher - Parts conveyor belt - Bar feeder interface

Kondisi: bekas, Tahun pembuatan: 1979, Fungsionalitas: berfungsi sepenuhnya, de-sn440-gewicht Crsdpfxef Dwa Ue Aavoi

Kondisi: bekas, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Max. rolling force: 24 tons Max. tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Max. holding/tool length: 180 mm Max. workpiece diameter: 50 mm Cjdpfx Aajuz If Njvjri Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Power supply: 400 Volt, 50 Hz, 10 kW - Swiveling roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox - Hydraulic system integrated in machine base - Operating manual with electrical schematic Space required (L x W x H): 2000 x 1450 x 190 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling dies with the same pitch as the workpiece form the thread by penetrating into the workpiece up to the nominal diameter. The maximum thread length corresponds to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the die width. Through-feed dies have three sections - the lead-in, the calibration zone, and the lead-out. Groove rolls have no pitch and are swiveled according to the thread pitch angle to be rolled. Pitch rolls differ from groove rolls by having a pitch in the profile. The sum of the pitch angle and the swivel angle gives the pitch angle in the workpiece.

Kondisi: baik (bekas), Tahun pembuatan: 2004, Fungsionalitas: berfungsi sepenuhnya, Perlengkapan: kecepatan rotasi dapat diubah tanpa batas, Citizen C16-VII CNC Swiss Type Lathe Year of manufacture: 2004 Control: Mitsubishi Meldas 635 Max. machining diameter: 16mm C-axis: Main and Sub Spindle 5 controlled servo axes: X1/Z1/Y1/X2/Z3 4 driven tools on the vertical tool holder C-axis: Main and sub spindle Crsdjv Rhd Hepfx Aavei Including accessories: LNS Express 220 bar feeder, conversion kit for 16mm and 10mm Donaldson Torit extraction system Chip conveyor - Immediately available -

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2017, jam operasional: 24.140 h, berat keseluruhan: 10.000 kg, produsen pengendali: FANUC, model controller: 31i-NT-SmartX, jumlah sumbu: 9, This 9-axis Nakamura NTJ100 turning-milling center was manufactured in 2017 and features a bar capacity of up to 65 mm, as well as two spindles with maximum speeds of 4,500 and 5,000 rpm, respectively. It comes equipped with a Samsys bar feeder, an Absolent extraction system, and a wide range of automated features, including through-spindle coolant supply, parts catcher, and automatic tool presetting devices. Seize the opportunity to purchase this Nakamura NTJ100 turn-mill center. Contact us for further information about this machine. • Increased bar capacity: 65 mm left, 51 mm right • Workpiece measurement: Han-Bei probe for automatic workpiece measurement (infrared or radio) for both left and right spindle • Left and right, with automatic swivel and 2x 4 measuring directions for fast, precise tool presetting via NC function • Operating hours: 43,399h • Coolant system: Coolant through spindle (CTS); coolant float switch for machine stop at low level; additional coolant flush through both spindles (left and right) • Bar capacity: Ø 51 mm • Type A parts catcher with collecting tray, max. Ø 65 x 150 mm, 3.0 kg, spindle side, left, with plastic lining • Chuck air blow device for left spindle • Automatic power shut-off • Preparation for oil mist extraction system with connecting stub Ø 150 mm • Robot/automation preparation: Pneumatic flap for robot handling on the top of the door, opening approx. 400 x 400 mm • Handwheel for manual positioning of defined contours • Data server with 1 GB ATA memory card • Interface for KNOLL system • Three-color signal light Crsdpfx Aex D Iuzoavji The Samsys bar loader with 1.5 m loading length has the following dimensions: Length: 225 cm + 43 cm intermediate guide; Width: 120 cm (including loading ramp and control panel); Height: 145 cm or 180 cm with open hatch The machine was mainly used for machining aluminum (95%). Additional equipment: • Samsys bar feeder, including extension • Absolent extraction unit • Hinged belt chip conveyor with interface, interval control, and alarm monitoring

Tahun pembuatan: 2005, Kondisi: siap digunakan (bekas), - GEBRAUCHT - 6-ACHSEN-SCHIEBEKOPF-DREHMASCHINE MIT STANGENLADER MAX. DREHLÄNGE: 320 mm MAX. DREHDURCHMESSER: 32 mm SPINDEL: 200-8000 U/min; 3,7 - 7,5 kW GEGENSPINDEL: 200-7000 U/min; 1,5 - 2,7 kW X1-ACHS-VERFAHRWEG: 108 mm X2-ACHS-VERFAHRWEG: 228 mm Crsdevthv Ijpfx Aavoi Y1-ACHS-VERFAHRWEG: 275 mm Z1-ACHS-VERFAHRWEG: 325 mm Z2-ACHS-VERFAHRWEG: 130 mm Z3-ACHS-VERFAHRWEG: 410 mm EILGÄNGE X-Y-Z: 20 m/min ANGETRIEBENER REVOLVERKOPF: 8 STELLUNGEN; 200 - 5000 U/min STEUERUNG: CINCOM SYSTEM M6D STANGENLADER: IEMCA Mod. BOSS 332 EVOLUTION GEWICHT: 2.850 kg ZUBEHÖR: TEILEFÄNGER

Kondisi: belum diuji (bekas), Tahun pembuatan: 2008, Fungsionalitas: belum diuji, nomor mesin/kendaraan: R14507, en-01 Cjdpfeya Aq Rox Aavsri

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2014, jam operasional: 51.488 h, Mesin bubut tipe swiss Citizen CINCOM A32-VII CL ini diproduksi pada tahun 2014. Dilengkapi spindle utama dengan kapasitas 32 mm, counter spindle, serta panjang pembubutan maksimum hingga 3000 mm. Dilengkapi sistem CHIDOMI berkecepatan tinggi, mesin ini mendukung pergerakan simultan di semua sumbu dan menawarkan kecepatan pemakanan hingga 9.000 mm/menit. Pertimbangkan kesempatan untuk membeli Citizen CINCOM A32-VII CL tipe swiss ini. Hubungi kami untuk informasi lebih lanjut mengenai mesin ini. Crjdsx D Nhpspfx Aavsi Jenis Aplikasi Bubut

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2015, jam operasional: 48.086 h, produsen pengendali: SIEMENS, model controller: 840D, jumlah sumbu: 3, Mesin 3 sumbu DMG MORI CTX Beta 800 4a ini diproduksi pada tahun 2015. Mesin ini dilengkapi dengan kontrol Siemens 840 D, spindel utama dan spindel kedua, serta paket pemesinan batang untuk pengoperasian yang efisien. Mesin ini ideal untuk pekerjaan pembubutan dan pemesinan kompleks, serta memiliki konveyor artikulasi dan sistem pendingin dengan beberapa pengaturan tekanan. Jika Anda mencari kapasitas pembubutan berkualitas tinggi, Anda dapat mempertimbangkan mesin DMG MORI CTX Beta 800 4a yang kami tawarkan untuk dijual. Mesin ini berlokasi di Jerman. Hubungi kami untuk informasi lebih lanjut. • Spindel utama IMS 76 • Spindel kedua • 2 x Revolver bintang Sauter 16 posisi VID 30 • Kontrol Siemens 840D • Pembubutan dan pemesinan eksentrik • TC dengan kecepatan variabel • Skala kaca pada X1, X2, X3, Y1, Z1, Z2, Z3 • Penggeser spindel kedua dengan gerakan melintang, C3, tailstock Peralatan tambahan • Sistem pendingin 980 liter dengan tekanan tinggi 8 bar/20 liter dan 20 bar/40 liter, fungsi M dapat diprogram • Filter pita kertas • Perangkat pembilasan chuck untuk spindel utama (luar) • Perangkat pembilasan chuck untuk spindel kedua (luar) • Pistol semprot pendingin • Konveyor serpihan artikulasi Csdpfxsx D Ndwo Aaveri • Sistem pemesinan batang (umpan batang) • Pembersihan jendela dengan udara bertekanan • Paket SK untuk pemesinan aluminium • Pemantauan kerusakan alat Artis CTM

Kondisi: bekas, 1 Credpfswwa Dkjx Aavsi