112

MACPRESSE EUROPA S.R.L. 112

Kondisi: sangat baik (bekas), Tahun pembuatan: 2023, jam operasional: 1.851 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 70 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.400 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 500 kg, berat keseluruhan: 17.000 kg, kapasitas tangki oli: 70 l, Technical data baler: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: AVOS 1410 BS-22/50 Year of manufacture: 2023 Operating hours pump: 1,851 hours (as of July 2024) Pressing force: 70 t (equipped with a 70 t hydraulic cylinder, special equipment) Specific pressing force: 90.9 N/cm² (equipped with a 70 t hydraulic cylinder, special equipment) Feed opening dimensions: 1,400 x 1,000 mm Theoretical cycle time: 13 seconds Theoretical throughput: 266 m³/h Bale dimensions: 1,100 x 750 mm (W x H), length variable Drive power: 22 kW Total installed power: 65 kW Ijdpsu Thbxjfx Ab Isa Tying: 4-fold vertical, fully automatic Throughput rates at a bulk density of: - 30 kg/m³ approx. 5.5 t/h - 50 kg/m³ approx. 7.5 t/h - 100 kg/m³ approx. 9.7 t/h Bale weights with a bale length of approx. 1.2 m: up to 500 kg (material dependent) PLC control: Siemens S7-1500 Operator panel: Schneider Harmony Baler dimensions (assembled): 8,610 x 2,400 x 3,835 mm (L x W x H) Transport weight baler: 17 t Special equipment: - Wear-resistant floor made of HARDOX steel - Larger main hydraulic cylinder with 70 t pressing force - Special press ram for processing loose bulk materials of small grain size - OptiCut XS system for reduced cutting force and increased throughput - Special press ram for compacting "difficult" materials Technical data conveyor belt: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: KGF GB 1500 Year of manufacture: 2023 Drive power: 4.0 kW Belt speed: approx. 0.3 m/s Feed belt length: 2,679 mm Inclined belt length: 6,866 mm Gooseneck length: 1,272 mm Incline: 35° Usable width: 1,400 mm Sidewall height (inclined belt): 800 mm Cleat height: 50 mm Cleat spacing: 750 mm Belt specification: EP 400/3, 3:1 (DIN quality N) Total height: 4,515 mm Transport dimensions (overall): 11,148 x 2,502 mm (L x W) Technical data contactless personnel protection system: Manufacturer: BOREMA Umwelttechnik AG, Switzerland Model: APSS iBOR 22 Year of manufacture: 2023 Condition of the baling line: The entire plant is in very good condition due to its low operating time of only 1,851 pump hours and processing exclusively paper, cardboard, and film. Scope of delivery: - Avermann baler, model AVOS 1410 BS-22/50, incl. wire threading stations and bale chute - Avermann conveyor, model KGF GB 1500 - BOREMA personnel protection system, model APSS iBOR 22 Remarks: Complete documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available. Inspection possible by appointment. No liability is assumed for technical specifications or possible errors.

Tahun pembuatan: 2008, jam operasional: 40.000 h, Kondisi: baik (bekas), nomor mesin/kendaraan: HBC 140 2x75kW 2008 (00191), Verkocht door Bollegraaf Recycling Solutions, de originele fabrikant van deze Bollegraaf-pers en transportband: Bollegraaf HBC140s Kanaalbalenpers (2x75 kW). Pers: Gewicht: 47.100 kg Bouwjaar: 2008 Enkel Hardox bodemplaat Variabele kanaaldrukregeling Kunststof ventiel Ijdjkcgf Hjpfx Ab Iea Hydraulische pomp aangedreven door frequentieomvormer Anti-ratten bekabeling Dieptefiltratie van olie Modem Bedrijfsuren: 40.000 Deze balenpers kan ook volledig gereviseerd worden verkocht volgens de 'Bollegraaf OEM Certified Refurbishment standards'. Hierbij krijgt u 2 jaar garantie. Neem contact met ons op voor meer informatie of een offerte. Algemene beginselen van revisie Reiniging & demontage Voor de daadwerkelijke revisie wordt de pers volledig gereinigd en gedemonteerd in onze revisiewerkplaats. Maatvoering Na demontage worden de toleranties van alle stalen componenten gemeten en waar nodig opnieuw gelast. Dit geldt in ieder geval voor de volgende onderdelen: • Ram, • Frame, • Kanaal, • Voorpersklep Na demontage en inspectie wordt de persram weer opgelast en voorzien van nieuwe ramwielen. De beschermroosters en de voorpersklep worden waar nodig hersteld en uitgedeukt. Overschilderen Na het meten van de toleranties en eventuele herstel- en laswerkzaamheden worden alle onderdelen gestraald en opnieuw gecoat. Hydrauliek: De hydrauliektank wordt gereinigd. De hydrauliekleidingen en -slangen worden vervangen. De hydraulische componenten worden opnieuw gepakt. De hydrauliekolie wordt vervangen. Bekabeling: Alle bekabeling wordt gecontroleerd en indien nodig vernieuwd. Alle lasdozen worden vervangen en teruggeplaatst op goed toegankelijke posities. Slijtagedelen: Alle slijtagedelen worden vervangen. De pennen en assen van de cilinders en het perskanaal worden vernieuwd. Alle slijtagedelen van (beide) naaldinrichtingen en knopers worden vervangen. Cilinders: De cilinders worden opnieuw gepakt en indien nodig voorzien van een nieuwe chroomlaag of een nieuwe zuigerstang. MCC-kast: De schakelkast wordt gecontroleerd en gereinigd. Indien nodig worden elektronische componenten vernieuwd. PLC en HMI (bedieninterface) worden vervangen door de nieuwste Schneider M340 variant met up-to-date software.

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2003, Complete plant specially designed for exceptionally hard and abrasive stone. Primary unit: Baxter double-toggle jaw crusher 50x36 inches. New jaws installed. Iodpsim D Uujfx Ab Iea Electric motors included. Entire assembly inspected and overhauled in workshop; excellent condition. Vibrating grizzly feeder 1400x6000 mm. Hopper with 40 m³ capacity. Mounted on bolted steel structure. Svedala 16-45 gyratory crusher. Asteca screen 2500x6000 mm, 3 decks. Conveyor belts, etc.

Kondisi: bekas, Tahun pembuatan: 2009, jam operasional: 20.536 h, gaya penekanan: 80 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.400 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 600 kg, berat kosong: 16.000 kg, Technical Data – Baler: Iedpfsu Thypsx Ab Iea Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: AVOS 1410-45/80 Year of manufacture: 2009 Operating hours: 20,536 hours (as of September 2024) Pressing force: 80 kN Specific pressing force: 103.9 N/cm² Feed hopper dimensions: 1,400 x 1,000 mm Theoretical cycle time: 12 seconds Theoretical throughput: 300 m³/hour Bale dimensions: 1,100 x 750 mm (W x H), length variable Drive power: 45 kW Total connected load: 75 kW Tying: 4-fold vertical, fully automatic Throughput rates at bulk densities of: – 30 kg/m³: approx. 6.0 t/h – 50 kg/m³: approx. 10.5 t/h – 100 kg/m³: approx. 17.5 t/h Bale weights at a bale length of approx. 1.2 m: up to 600 kg, depending on material PLC control: Siemens S7-300 Display panel: pulsotronic Installed press dimensions: 8,610 x 2,400 x 3,835 mm (L x W x H) Transport weight (press): 16 t Special equipment: – Wear-resistant floor made of HARDOX steel – Special press ram for compacting "difficult" materials and loose bulk goods with small grain size – Control cabinet climate control – Machine foot raising by 200 mm Note: The machine is currently in our workshop and undergoing partial refurbishment. We expect the refurbishment to be completed by the end of October, after which the machine will be tested and released for sale.

Kondisi: belum diuji (bekas), Hydraulic press for compacting paper and similar materials. The machine was fully operational prior to disassembly. Ijdsh Nyfyjpfx Ab Iea Press dimensions: Length: 4850 mm, width: 1370 mm, height: 3000 mm (can be reduced to 2300 mm). Weight approx. 3500 – 4000 kg. For further information, please contact: +48 539 660 495.

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2012, jam operasional: 25.895 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 78 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.500 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 600 kg, berat keseluruhan: 24.000 kg, kapasitas tangki oli: 1.000 l, daya: 55 kW (74,78 hp), laju aliran volumetrik: 930 m³/jam, Technical Data — Baler: Manufacturer: Presona AB Type: LP 80 VHK 1 Year of manufacture: 2012 Total operating hours (machine): 25,895 hours (as of July 2025) Effective pump operating hours: 14,135 hours (as of July 2025) Number of bales produced: 235,597 units (as of July 2025) Main press force: 78.5 t Specific pressing force: 95 N/cm² Pre-press force: 28 t Press chamber volume: 2.7 m³ Feed hopper dimensions: 1,500 x 1,100 mm Theoretical throughput: 930 m³/hour Throughput under operating conditions: 410 m³/hour Bale dimensions: 750 x 1,100 mm Drive power: 55 kW Tying: 5-fold vertical, 3-fold horizontal, fully automatic Throughput at bulk density of: 30 kg/m³: approx. 9 to 12 t/hour, material-dependent 50 kg/m³: approx. 14 to 17 t/hour, material-dependent 100 kg/m³: approx. 16 to 25 t/hour, material-dependent Throughput for MSW (Municipal Solid Waste): approx. 20 to 27 t/hour, material-dependent Bale weights: 450 to 600 kg, depending on material and bale length Hydraulic oil tank volume: 1,000 L Baler dimensions (installed with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Transport dimensions (baler only): 10,985 x 2,300 x 2,900 mm Machine weight (baler): approx. 24 t Condition of the baler: The machine has been partially overhauled and serviced in our workshop. After completion of the work, it was tested during live operation, both in manual and automatic mode. The following overhaul work was carried out: - Machine cleaned, partially derusted and partially repainted - Hydraulic oil tank fully drained and cleaned - Oil and air filters replaced, new hydraulic oil filled - Press ram disassembled and cleaned - All four running rollers on the press ram replaced - Wire station with guide rollers for the bottom wire cleaned and made operational - Side guides removed from press ram, smoothed, reinstalled and readjusted - Main hydraulic cylinder removed, dismantled and inspected - Piston rod replaced, cylinder tube honed - Complete seal kit replaced, pressure test performed - Hydraulic hose from main hydraulic cylinder replaced - Vertical and horizontal needle systems for tying disassembled, cleaned, wire guide rollers made operational and maintained - Chain cleaned, lubricated, chain tension readjusted Isdovwlqqspfx Ab Ija - Drillomat cleaned, wire knives, twister shafts and twister fingers checked, torqued, and serviced - Door contact switches checked and partially replaced - Emergency stop button tested - Complete electrical wiring checked and partially renewed - Bearings of wire guide rollers below the baler replaced - New safety grids for vertical and horizontal tying manufactured and installed - Machine inspected, general maintenance performed and baler tested in manual and automatic operation Scope of delivery: Only the baler is for sale. Remarks: All documentation (operating manual, CE declaration, electrical/hydraulic schematics) is complete and available. An inspection can be arranged by appointment. We assume no liability for technical specifications or possible errors.

Kondisi: baru, The solution for shredding large, long pipes and profiles. The ZRS series is specifically designed for the size reduction of pipes with diameters up to 1,300 mm and made from various materials such as PE, PP, and PVC. Ijdpfoghgd Ijx Ab Ija These machines are capable of shredding plastic pipes up to 9 meters in length directly, without the need for pre-cutting or sawing. The centerpiece is a rotor with diameters up to 1,500 mm, which can be equipped with up to 206 cutting crowns and shreds material gently at low rotational speed. The pipe is loaded into a closed feed trough, where it is pressed against the rotor by a hydraulic pusher. The pre-shredded material is then conveyed by the shredder via a conveyor belt to a granulator. The granulator processes the material into regrind directly suitable for further processing. The entire system is operated automatically via a central control unit. Additional benefits of the system include low energy consumption, avoidance of power peaks, and the minimization of accident risks during pre-shredding.

Tahun pembuatan: 2015, Kondisi: diremaj di bengkel (bekas), Technical data for feed hopper with hydraulic moving floor and sack opener: Isdpfxju R Rtbo Ab Ija Manufacturer: BRT HARTNER GmbH Model: HP5-3035 Year of manufacture: 2015 Hopper volume: 30 m³ Drive power: 17.5 kW Dimensions (current state): 13,200 x 3,050 x 4,350 mm (L x W x H) Condition of the machine: The feed hopper with sack opener was in operation at a large recycling facility, where bagged waste was loaded into the hopper with wheel loaders. The bags were opened by the sack opener, and the waste was metered for further processing. The unit operated flawlessly until it was dismantled and replaced by a larger, higher-throughput system. Remarks: The machine is currently undergoing refurbishment in our workshop. The photos show the machine at its current stage of refurbishment, so it is not yet fully assembled. After completion of the refurbishment work, expected in February 2025, the machine will be tested under operating conditions without material. Documentation (operating manual, CE declaration, electrical/hydraulic circuit diagrams) is complete. Viewing by appointment is possible. We accept no liability for the technical specifications or possible errors.

Kondisi: sangat baik (bekas), Tahun pembuatan: 2007, jam operasional: 21.676 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 78 t, lebar bukaan pengisian: 750 mm, panjang bukaan pengisian: 1.500 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 600 kg, berat keseluruhan: 25.000 kg, tinggi transportasi: 3.000 mm, kapasitas tangki oli: 1.000 l, daya: 55 kW (74,78 hp), berat kosong: 25.000 kg, laju aliran volumetrik: 930 m³/jam, tekanan kerja: 250 batang, Hello, We hereby offer you, without obligation, a used baler from the manufacturer Presona AB, type LP 80 VH1. The following technical data has been taken from the manufacturer's operating manual and brochures. We cannot guarantee the accuracy or completeness of this information. Manufacturer: Presona AB, Sweden Iodpfx Absvgrh Uj Ioa Type: LP 80 VH1 Year of manufacture: 2007 Total operating hours: 21,676 hours (as of November 2024) Pressing force (main press): 78 t Specific pressing force: 95 N/cm² Pre-press lid force: 28 t Feed opening dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank volume: 1,000 l Press dimensions (assembled with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight (press): approx. 25 t Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The baler is in good condition, will remain in operation until January 2025, and can be inspected by appointment. We would be pleased if this machine is of interest to you. Your service team at Mertens & Frowein GmbH

Kondisi: baru, Tahun pembuatan: 2025, CHIPPER MACHINE, brand KÄLIN Hobeltechnik, model MPC-P: • Approximate production of wet shavings: 3,800 kg/h • Log carriage dimensions: 2,800mm x 1,100mm x 1,300mm • Maximum log length: 2,650mm • 2 symmetrical, removable cutter heads of 1,140mm each, divided into 3 sections of: - Diameter: 200mm - Length: 380mm - Number of knives: 8 - Cutter heads can be sharpened as a complete unit, without needing to remove the knives Iodpsvk Saxsfx Ab Isa - ULTRA-FAST CUTTER HEAD CHANGE, less than 15 minutes! • 2 spare sets of cutter heads for replacement during the sharpening process • Cutter head motor power: 90kW / 120 HP • Carriage speed controlled by ELECTRONIC INVERTER: 0.6 to 36 m/min • Automatic control of the feed-to-load ratio • 1 feed drive motor, heavy-duty double chain drive: 15kW / 20 HP • Material level control system within the carriage to prevent running empty • Electrical cabinet and control panel with touch screen for function management • Lower motorized discharge conveyor for shavings: 5,000 mm x 800 mm • Weight: 11,000 kg • CE-compliant