Bus

setra S415 NF - EEV1 EURO 5 STANDHEIZUNG

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2012, jam operasional: 25.895 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 78 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.500 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 600 kg, berat keseluruhan: 24.000 kg, kapasitas tangki oli: 1.000 l, daya: 55 kW (74,78 hp), laju aliran volumetrik: 930 m³/jam, Technical Data — Baler: Gijdpfovwlqqsx Adtsl Manufacturer: Presona AB Type: LP 80 VHK 1 Year of manufacture: 2012 Total operating hours (machine): 25,895 hours (as of July 2025) Effective pump operating hours: 14,135 hours (as of July 2025) Number of bales produced: 235,597 units (as of July 2025) Main press force: 78.5 t Specific pressing force: 95 N/cm² Pre-press force: 28 t Press chamber volume: 2.7 m³ Feed hopper dimensions: 1,500 x 1,100 mm Theoretical throughput: 930 m³/hour Throughput under operating conditions: 410 m³/hour Bale dimensions: 750 x 1,100 mm Drive power: 55 kW Tying: 5-fold vertical, 3-fold horizontal, fully automatic Throughput at bulk density of: 30 kg/m³: approx. 9 to 12 t/hour, material-dependent 50 kg/m³: approx. 14 to 17 t/hour, material-dependent 100 kg/m³: approx. 16 to 25 t/hour, material-dependent Throughput for MSW (Municipal Solid Waste): approx. 20 to 27 t/hour, material-dependent Bale weights: 450 to 600 kg, depending on material and bale length Hydraulic oil tank volume: 1,000 L Baler dimensions (installed with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Transport dimensions (baler only): 10,985 x 2,300 x 2,900 mm Machine weight (baler): approx. 24 t Condition of the baler: The machine has been partially overhauled and serviced in our workshop. After completion of the work, it was tested during live operation, both in manual and automatic mode. The following overhaul work was carried out: - Machine cleaned, partially derusted and partially repainted - Hydraulic oil tank fully drained and cleaned - Oil and air filters replaced, new hydraulic oil filled - Press ram disassembled and cleaned - All four running rollers on the press ram replaced - Wire station with guide rollers for the bottom wire cleaned and made operational - Side guides removed from press ram, smoothed, reinstalled and readjusted - Main hydraulic cylinder removed, dismantled and inspected - Piston rod replaced, cylinder tube honed - Complete seal kit replaced, pressure test performed - Hydraulic hose from main hydraulic cylinder replaced - Vertical and horizontal needle systems for tying disassembled, cleaned, wire guide rollers made operational and maintained - Chain cleaned, lubricated, chain tension readjusted - Drillomat cleaned, wire knives, twister shafts and twister fingers checked, torqued, and serviced - Door contact switches checked and partially replaced - Emergency stop button tested - Complete electrical wiring checked and partially renewed - Bearings of wire guide rollers below the baler replaced - New safety grids for vertical and horizontal tying manufactured and installed - Machine inspected, general maintenance performed and baler tested in manual and automatic operation Scope of delivery: Only the baler is for sale. Remarks: All documentation (operating manual, CE declaration, electrical/hydraulic schematics) is complete and available. An inspection can be arranged by appointment. We assume no liability for technical specifications or possible errors.

Kondisi: bekas, Tahun pembuatan: 2003, Technical details: Pressing force: 40 t Hopper opening: 1200 x 730 mm Material: Cardboard, plastic – e.g., PET bottles Voltage: 400 V / 50 Hz Total power requirement: 16.4 kW Transport dimensions (machine): 6.5 x 6.2 x 2.7 m Gsdpfxsu Nw Ezs Adtsil Fully automatic hydraulic CHANNEL BALER for recycling applications – Incl. feed unit/conveyor belt, LxW: 4500 x 1000 mm, motor-driven – Equipped with automatic 3-fold tying unit – Bale counter/display Press chamber (LxWxH): 1800 x 800 x 800 mm with 1.2 m³ volume Bale size (LxWxH): 300–1500 x 800 x 800 mm Bale weight: 250–450 kg, depending on material and bale length Filling opening (LxW): 1200 x 730 mm; Filling height: 1200 mm Hopper size (LxWxH): 1200 x 1200 x 1400 mm; Fill height: 2500 mm

Tahun pembuatan: 2003, jam operasional: 43.000 h, Kondisi: perlu perbaikan (bekas), nomor mesin/kendaraan: HBC 140 2x75kW 2003 (W230-005), nl-naar-en Giodpfxskcgyns Adtjl

Tahun pembuatan: 2008, Kondisi: bekas, 20081 Godpfxew Ia Ngj Adtoil

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2001, Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: HBC 140 2x75kW 2001 (210-008-01), gaya penekanan: 155 t, berat bal: 1.500 kg, tekanan: 250 batang, daya: 150 kW (203,94 hp), tahun perombakan terakhir: 2024, Perlengkapan: dokumentasi / manual, Verkocht door Bollegraaf Recycling Solutions, de oorspronkelijke fabrikant van deze Bollegraaf-pers en transportband: Bollegraaf HBC140s Balenpers (2x75kW). Pers: Gewicht: 47.100 kg Bouwjaar: 2001 Variabele kanaaldrukregeling Kunststof ventiel Anti-rattenbekabeling Gsdpfx Aetvau Asdteil 0 uur na volledige revisie Deze pers wordt volledig gereviseerd verkocht volgens de 'Bollegraaf OEM Gecertificeerde Revisiestandaarden'. Dit bevat 2 jaar garantie. Neem contact met ons op voor meer informatie of een offerte. Algemene principes van revisie Reiniging & demontage Voordat de daadwerkelijke revisie plaatsvindt, wordt de pers volledig gereinigd en gedemonteerd in onze revisiewerkplaats. Toleranties Na de demontage worden de toleranties van alle stalen componenten gemeten en waar nodig opnieuw gelast. Dit geldt in ieder geval voor de volgende onderdelen: • Persplunjer • Frame • Kanaal • Voordruk-klep Na demontage en inspectie wordt de persplunjer opnieuw opgelast en voorzien van nieuwe plunjerwielen. De beschermroosters en de voordruk-klep worden uitgedeukt en waar nodig gerepareerd. Opnieuw gespoten Na het meten van de toleranties en eventueel las- en herstelwerk worden alle onderdelen gestraald en opnieuw gecoat. Hydrauliek: De hydrauliektank wordt gereinigd. De hydraulische leidingen en slangen worden vervangen. De hydraulische componenten worden gereviseerd. De hydraulische olie wordt ververst. Bekabeling: Alle bekabeling wordt gecontroleerd en indien nodig vervangen. Alle aansluitdozen worden vervangen en teruggeplaatst op eenvoudig toegankelijke posities. Slijtagedelen: Alle slijtagedelen worden vervangen. De pennen en assen van de cilinders en het kanaal worden vernieuwd. Alle slijtagedelen van (beide) naaldinstallaties en knopers worden vervangen. Cilinders: De cilinders worden gereviseerd en indien nodig voorzien van een nieuwe chroomlaag of een nieuwe cilinderstang. MCC Kast De schakelkast wordt gecontroleerd en gereinigd. Indien nodig worden elektronische componenten vernieuwd. De PLC en HMI (‘human interface’) worden vervangen door de nieuwste Schneider M340-versie inclusief de nieuwste software.

Kondisi: diremajakan ulang (bekas), Tahun pembuatan: 1999, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 71 t, lebar bukaan pengisian: 1.080 mm, panjang bukaan pengisian: 1.620 mm, lebar bal: 1.100 mm, tinggi bal: 720 mm, berat bal: 600 kg, lebar total: 3.450 mm, tinggi total: 4.090 mm, panjang total: 10.020 mm, tegangan masuk: 400 V, berat keseluruhan: 27.000 kg, tingkat kebisingan: 85 dB, tekanan: 300 batang, tinggi transportasi: 2.300 mm, daya: 37 kW (50,31 hp), nl-hu-001 Godpexl Rqbefx Adtoil

Kondisi: sangat baik (bekas), Tahun pembuatan: 2022, Fungsionalitas: berfungsi sepenuhnya, Technical Data for EPS (Styrofoam) Compactor: Manufacturer: FZ-Recycling GmbH & Co. KG, Germany Model: FZR 320 Year of Manufacture: 12/2022 Drive Power (Shredder): 4 kW Drive Power (Compacting Screw): 7.5 kW Drive Power (Hydraulic Unit for Retaining Clamp in Press Channel): 1.1 kW Total Connected Load: 12.6 kW Power Requirement: 32 A Godeu Thkajpfx Adteil Compression Ratio of Compacted Blocks to Original Material: approx. 50:1 (depending on material) Block Weight After Compaction: approx. 300 kg/m³ (material dependent) Block Dimensions: 320 x 320 mm, length variable Throughput Capacity: approx. 100 kg/hour (depending on material) Achievable Density: approx. 250 – 300 kg/m³ Compacted blocks are stacked approx. 1400 mm high on a pallet and wrapped with stretch film. Machine Dimensions: approx. 4,600 x 1,400 x 1,980 mm (L x W x H) Transport Weight (Compactor): 1,325 kg Condition of the Compactor: The compactor was only used sporadically, is in very good condition, and available at short notice. Due to the low machine weight and forklift pockets in the transport frame, the machine is mobile and can be used directly at the material source, e.g., on the construction site. Electrical connection is via a CEE 32 A plug. Scope of Delivery: 1 piece EPS compactor, ready for connection and operation. Remarks: Complete documentation (operating manual, CE declaration, electrical/hydraulic wiring diagram) is available. Inspection possible by appointment. No liability is assumed for technical specifications or possible errors.

Kondisi: sangat baik (bekas), Tahun pembuatan: 2017, jam operasional: 13.284 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 140 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.600 mm, lebar bal: 1.100 mm, tinggi bal: 1.100 mm, berat bal: 1.500 kg, kapasitas tangki oli: 2.600 l, en-001 Gsdjxpxhvjpfx Adtsil

Kondisi: sangat baik (bekas), Tahun pembuatan: 1998, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 25 t, lebar bukaan pengisian: 800 mm, panjang bukaan pengisian: 1.050 mm, lebar bal: 900 mm, tinggi bal: 800 mm, tegangan masuk: 400 V, tingkat kebisingan: 85 dB, daya: 18,5 kW (25,15 hp), laju aliran volumetrik: 160 m³/jam, Bollegraaf HBK25 ditawarkan di Siprus. Mesin dalam kondisi baik dan termasuk konveyor pada lantai. Tersedia segera. Data teknis mesin baler: Penggerak: 18,5 kW Ukuran bal: 800 x 900 x dapat diatur Ukuran hopper: 1.050 x 800 mm Gaya tekan: 25 ton Giedjxbdgujpfx Adtjl Kapasitas: 160 m3/jam (tergantung material) Data teknis konveyor (perkiraan): Panjang di lantai: 3.000 mm Panjang diagonal: 5.000 mm

Kondisi: bekas, Tahun pembuatan: 2006, jam operasional: 54.050 h, gaya penekanan: 80 t, lebar bukaan pengisian: 1.020 mm, panjang bukaan pengisian: 1.600 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 750 kg, kapasitas tangki oli: 2.100 l, daya: 94 kW (127,80 hp), berat kosong: 21.000 kg, Technical Data – Baler: Godpfx Adexcxm Ejteil Manufacturer: Paal Model: Konti 275 E Year of manufacture: 2006 Total operating hours: 54,050 hours Main press force: 80 t at 300 bar Specific press force: 9.7 kg/cm² Feeding chute dimensions: 1,600 x 1,020 mm (L x W) Throughput under operating conditions: 350 m³/h Bale dimensions: 750 x 1,100 mm, length variable Drive power: 75 kW Total connected load: 94 kW Rated current: 180 A Tying system: 4-fold vertical, fully automatic Bale weights: up to 750 kg, depending on material Hydraulic oil tank volume: 2,100 L PLC (Make/Type): Siemens Simatic S7-300 Control panel (Make/Type): Siemens Multi Panel Transport dimensions press only: 11,152 x 2,152 x 3,000 mm (L x W x H) Press weight approx.: 21 t Condition of baler with conveyor: The baler and conveyor are in a satisfactory, operational condition, see photo documentation. Further technical data and dimensions for the conveyor are currently not available. The plant is currently still in operation and will be replaced in the coming months by a larger baling system. Scope of supply: Baler, bale slide, conveyor belt and machine documentation. Remarks: The documentation (operating manual, CE, electric/hydraulic circuit diagrams) is complete. An inspection is possible by arrangement. Dismantling and loading is the responsibility of the buyer. We do not accept liability for the technical data or for possible errors.