HSM VK 88 + Stadler KF1800

HSM VK 8818

Kondisi: sangat baik (bekas), Tahun pembuatan: 2015, jam operasional: 20.331 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 100 t, lebar bukaan pengisian: 970 mm, panjang bukaan pengisian: 1.800 mm, panjang bal: 1.200 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 750 kg, berat keseluruhan: 33.000 kg, Good day, We hereby offer you, without obligation, a used, complete baling press line consisting of a baling press from the manufacturer HSM, type VK 8818 R-FU incl. conveyor technology and wire tie stations. The following technical data have been taken from the manufacturer’s operating manual and brochures, for the accuracy and completeness of which we assume no liability. Technical specifications of the press: Manufacturer: HSM GmbH + Co. KG, Germany Type: VK 8818 R-FU Year of manufacture: 2015 Operating hours: 20,331 hours (as of September 2025) Number of bales pressed: 29,020 bales (as of September 2025) Main press force: 1000 kN Specific press force: 120 N/cm² Cutting edge ejector press force: 121 kN Feed chute dimensions: 970 x 1,800 mm Theoretical cycle time in idle: 8.3 seconds Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length variable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency controlled Connected load: 110 kW Total power consumption: 213 A Fusing: 250 A slow-blow Tying: 5-fold horizontal, fully automatic Throughput at a bulk density of: 20 kg/m³: 12.86 t/hour 50 kg/m³: 32.15 t/hour Bale weight at a bale length of approx. 1.2 m: 650 to 750 kg/bale, depending on material Hydraulic oil tank volume: 2,000 L HVI 46 PLC control: Siemens S7-300 Operator panel: Siemens TP 700 Press dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Installation dimensions with conveyor system: 35,000 x 8,480 x 7,745 mm (L x W x H) Weight of press: approx. 33 t (main press: approx. 12 t, press channel with bale clamp: approx. 10 t) Additionally ordered special equipment: Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to the standard drive (2 x 45 kW) with equal performance Manual enabling/disabling of the number of wire-tie circuits to save tying wire with non-expansive materials Cutting edge ejector with 121 kN press force Sensor-based wire monitoring, with press shut-off in case of wire break or end of wire Bale chute Visual warning signal mounted on the control cabinet Condition of the press: The complete press system (baler and conveyor technology) is in good, immediately operational condition and has been cleaned weekly by the operator, greased and maintained in accordance with the manufacturer’s guidelines. Technical data for the chain belt conveyor: Manufacturer: Stadler Anlagenbau GmbH Type: Chain Belt Conveyor KF 1800 Year of manufacture: 2015 Belt speed: 0.36 m/second Feed belt length: 7,000 mm Inclined belt length: 14,500 mm Gooseneck length: 1,550 mm Incline: 30° Nominal width: 1,800 mm Usable width: 1,638 mm Overall conveyor height: 7,745 mm Pit dimensions for conveyor: 11,200 x 3,000 x 1,250 mm (L x W x H) Scope of delivery: - HSM VK 8818 R-FU baler - Maintenance platform - Bale chute - Wire redirecting stations - Wire spool trolleys (without wire spools) - Stadler KF 1800 chain belt conveyor - Transverse sliding belt conveyor - Pit cover from feed conveyor to pit - Second control cabinet for operating the press at the conveyor - Machine documentation in English Delivery time: The entire system is already dismantled, stored, and can be loaded at short notice after receipt of payment. We would be pleased if this or one of our other presses is of interest to you. Hfjdpsyz Af Eefx Ahnoh Your Service Team, Mertens & Frowein GmbH

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2008, A SIG Corpoplast blow molding machine is available. Output: 21,600 bottles/hour. Bottle formats: 500ml/750ml/1000ml/1500ml. Maximum blow air pressure: 40 bar. Dimensions (L/W/H): approx. 7000mm/4300mm/3100mm. Weight: approx. 20,000kg. Includes Transver AG preform feeding system, year of manufacture: 2008, silo, elevator, sorting unit, and chute. Documentation is available. On-site inspection possible. Hedpfx Aot Eu Azohnjfh

Kondisi: sangat baik (bekas), Tahun pembuatan: 2015, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 100 t, Technical Data: Pressing force: 1,000 kN Specific pressing force: 121.2 N/cm² Drive power: 45 + 45 kW, frequency-controlled Voltage/Frequency: 400 V / 50 Hz Cycle time (idle): 8.3 s Idle capacity (theoretical): 643 m³/h Capacity at 50 kg/m³ (theoretical): 32.15 t/h Feed opening (W x L): 970 x 1,800 mm Bale dimensions (W x H x L): 1,100 x 750 x 600–2,000 mm Maximum bale weight: up to 700 kg or 800 kg, depending on material The baler feed system comprises the following components: - 1 fully enclosed STADLER chain conveyor with corresponding shaft covers - 1 support and maintenance platform for conveyor and hopper - 1 STADLER feeder - 1 automatic channel baler HSM VK8818 R FU (100 t) - 1 wire rack for 500-kg soft wire coils - 10 wire spool carts Hfodpsygud Aefx Ahneh - 1 multi-control unit for the baler - Complete engineering documentation and maintenance history - Serviced and maintained by the manufacturer Commissioning available upon request. Weight: 33,000 kg Binding type: Wire Suitable materials: plastic film, mixed paper, cardboard, hollow containers made of HDPE/LDPE, and plastic bottles The plant is operational and can be inspected during operation. The machine will be dismantled on 16th February and can then be inspected at our premises. Available immediately!

Kondisi: baik (bekas), Tahun pembuatan: 2011, jam operasional: 40.000 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 88 t, lebar bukaan pengisian: 990 mm, panjang bukaan pengisian: 1.800 mm, panjang bal: 1.200 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat keseluruhan: 23.000 kg, kapasitas tangki oli: 2.000 l, daya: 90 kW (122,37 hp), laju aliran volumetrik: 643 m³/jam, Good day, We hereby offer you, subject to prior sale, a used baler including conveyor belt, wire-tying stations, and bale slide from the manufacturer HSM GmbH + Co. KG, model VK 8818 FU. The following technical data have been taken from the manufacturer's operating manual and brochures, for which we assume no liability for accuracy or completeness. Manufacturer: HSM GmbH + Co. KG, Germany Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours (as of July 2025) Main press force: 880 kN Specific press force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length variable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Tying: 5-fold horizontal, fully automatic Hjdpfxjymmtce Ahnefh Press dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Installation dimensions incl. conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Note: The machine was used in a recycling facility for compacting paper, cardboard, and film materials. The baler is in good condition and will be replaced by a new, larger press in May/June 2026. Until then, the machine can be inspected in operation with material processing. We would be pleased if this press is of interest to you. Your Service Team Mertens & Frowein GmbH

Kondisi: bekas, Fungsionalitas: berfungsi sepenuhnya, Tahun pembuatan: 2008, - Mesin dalam kondisi teknis dan optik yang sangat baik - Tersedia segera - Penjualan termasuk: - Gunting scrap: Zato FCE40 atau Genesis GXP400R - Lengan (boom) Hedpfx Ahsy Dc Nvonefh - Perlengkapan tambahan tersedia secara terpisah

Kondisi: bekas, Tahun pembuatan: 1992, Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: SN 336, gaya potong: 420 t, daya: 80,9 kW (109,99 hp), lebar total: 2.800 mm, panjang total: 15.000 mm, tinggi total: 3.400 mm, berat keseluruhan: 54.000 kg, panjang pemotongan (maks.): 2.000 mm, tahun perombakan terakhir: 2016, Gunting hidrolik bekas LEFORT 420 t / Semi mobile Tipe C 420TD Termasuk kendali HF remote Hfsdpfsy Hq Eqsx Ahneh Dapat dipasang tanpa pondasi – Mesin dipasang pada rangka baja 300 mm, termasuk 4 penyangga samping untuk proses muat dan bongkar mandiri. Gaya potong: 4200 kN Lebar potong: 800 mm (pisau 820 mm) Tinggi potong: 520 mm

Kondisi: bekas, Tahun pembuatan: 1992, Automatic PET Bottle Stretch Blow Moulding Machine Hfsdpfx Aewa Rhrehnoh Manufacturer: SIDEL Model: SBO 4 S1 Year of manufacture: 1992 Output capacity: 4,000 for 1.5 L / 2 L bottles Installed power: 150 kW Included: 1.5 L moulds Preform feeder Technical condition: used machine, operational, program functioning properly

Kondisi: diremajakan ulang (bekas), Tahun pembuatan: 2012, Fungsionalitas: berfungsi sepenuhnya, daya: 261 kW (354,86 hp), Lindner Urraco U75 D pada sumbu roda dengan magnet dan remote control overhaul total Hjdpsytdkfjfx Ahnjfh Alat: Disk 6 pcs 7/7 desain Hammel (kondisi 85%) Total 9800 jam kerja 2024: transmisi baru, pompa hidrolik baru, motor hidrolik baru dipasang sekarang sekitar 600 jam kerja belt keluar diperbaiki, bagian magnet diganti alat 85% servis baru pengecatan baru siap digunakan segera

Kondisi: sangat baik (bekas), Tahun pembuatan: 2014, jam operasional: 8.900 h, nomor mesin/kendaraan: LP50VH2, Used Presona LP50 VH2 baler in good working condition with conveyor belt Technical data: LP 50VH2 - Theoretical volume capacity: 730 m³/h - Maximum throughput under load: 340 m³/h - Productivity at bulk density: - 30 kg/m³ = 7–9 t/h - 50 kg/m³ = 8–9 t/h - 100 kg/m³ = 11–14 t/h - Hopper length: 1,500 mm - Hopper width: 1,100 mm - Loading chamber volume: 2.7 m³ - Bale width: 1,100 mm - Bale height: 720 mm - Bale length: adjustable - Bale weight: 400–550 kg - Number of vertical tying wires: 5 pcs - Press force: 50 t - Specific pressure: 63 N/cm² Hfodjyrhi Nepfx Ahnoh - Max. hydraulic pressure: 250 N/cm² - Oil tank volume: 600 l - Electric motor power 400 V, 50 Hz: 1 x 45 kW - Oil cooler: 1 x 1.5 kW - Net weight approx.: 16 t - Year of manufacture: 2014 2) Feed Conveyor - Conveyor type: Chain conveyor - Year of manufacture: 2014 - Specifications: - Conveyor width: approx. 1,300 mm - Length of horizontal section: 5,500 mm - Length of inclined section: approx. 10,800 mm - Conveyor weight: approx. 6 t Scope of delivery: Baler, control cabinet, operating panel, and conveyor belt for sale. Documentation (operating manual, CE declaration, electrical/hydraulic schematic) is complete. Inspection possible by appointment. We accept no liability for technical information or possible errors. Video footage can be provided upon request.

Kondisi: sangat baik (bekas), Tahun pembuatan: 2014, jam operasional: 37.656 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 85 t, lebar bukaan pengisian: 1.500 mm, panjang bukaan pengisian: 1.100 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 650 kg, berat keseluruhan: 25.000 kg, kapasitas tangki oli: 1.000 l, tahun perombakan terakhir: 2024, laju aliran volumetrik: 410 m³/jam, lebar transportasi: 2.400 mm, panjang transportasi: 9.300 mm, Good day, We hereby offer you, subject to prior sale, a used baler from the manufacturer Presona AB, type LP 85 VH1. The following technical data has been taken from the manufacturer's operating manual and brochures. We do not assume any liability for the accuracy and completeness of this information. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours (as of March 25) Main press force: 85 t Hfsdpfev T I Evex Ahnoh Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale size: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank capacity: 1,000 L Baler dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Machine weight (press): approx. 25 t Note: The machine was used by a recycling company for compaction of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The baler is in good condition. Many wear parts and entire assemblies have already been renewed in the last 3 years. The machine has been regularly maintained. We would be pleased if this baler is of interest to you. Your Service Team, Mertens & Frowein GmbH