Single-sided folding edge banding machine IMA AVM/K/I/G80/822/S3R3L20 (2003)

IMA AVM/K/I/G80/822/S3R3L20

Single-sided edge trimming and gluing machine
Manufacturer: IMA
Type: AVM/K/I/G80/822/S3R3L20
Year of manufacture: 2003
For milling, edge gluing, and finishing for a standard groove - only for pre-shaped/pre-grooved doors and square-edged doors
Left-hand machine (fixed stop on the left).
Complete processing in 3 passes
1st pass: Processing of the top surface of the door (transverse processing)
2nd pass: Door long edge
3rd pass: Door long edge
During the 2nd and 3rd passes, the protruding transverse edge from the 1st pass is milled off by using a co-rotating/counter-rotating milling process.
Double groove gluing is only possible through modifications to the machine and subsequent manual finishing of the edge.
Max. door thickness:
- Straight edge: approx. 70 mm
- Groove gluing: approx. 60 mm

Stable machine frame as a support for aggregates and housing for electrical installation.
Drive for feed speeds of approx. 5-25 m/min., mechanically infinitely adjustable.
(not to be confused with processing speed)
Continuous, plastic-coated strip-type conveyor chain,
approx. 80 mm wide, with automatic central lubrication.
Manually height-adjustable top pressure with a V-belt 80 mm wide and spring-loaded, ball-bearing guide rollers.
Machine length approx. 10,900 mm
Infeed table at the machine inlet.
1 horizontal, manually adjustable, unheated stop bar
1 joiner milling unit
controllable, not swiveling, without sensing
with 2 motors, each 3 kW
Gluing unit
for optional operation of straight edge or softforming gluing,
by changing the glue application.
Edge material:
- Strips: up to 1.3 mm
- Roll material: 0.4-3 mm
- Solid wood strips: 6 mm

Strip length max.: 2550 mm
Strip height: 14-80 mm (depending on glue application)
with:
- Side adjustment by hand for the pneumatically controlled glue application.
- Height adjustment by hand -15mm downwards and up to +10mm upwards.

1 bell for the main pressure roller,
manually adjustable
1 glue application 0.8L,
max. edge height 70mm, straight edge with pneumatic quick-release,
Chem-Coat coated, electronic temperature control
1 hot melt glue application 0.8L
with quick-release, up to max. 80 mm high edge material, soft edge,
Chem-Coat coated, with temperature control and control unit
for the strip coating
1 automatic Quickmelt hot melt glue feeder
with a heating power of 5.0 kW
1 2-fold magazine
only for edge material up to 3.0 mm thick,
can be manually attached to the single-roll magazine
1 groove forming pressing unit
for pressing the edge material into the groove with:
- an activation unit 15 kW for re-activating the edge material for groove forming
- a pneumatically controlled forming shoe for the underlapping edge
- a pneumatically controlled forming shoe for the entire groove
Dcedpfszuykvjx Aavsp
- additional post-pressing rollers for the edge areas in the groove
- an electro-pneumatic lateral retraction device for the entire pressing unit

1 horizontal adjustment
with mechanical digital display
1 trimming unit for 2 motors
mounted on the top pressure
for trimming the front and rear edge/strip overhang,
for trimming cuts flush or with a bevel.
1 milling unit for 2 motors
with height sensing, side sensing,
for pre-milling from below and above
with 2 motors 1kW, 400V, 200Hz, 12,000 RPM,
30° swiveling
1 milling unit for 2 motors
with height sensing, side sensing,
for fine milling from below and above
with 2 motors 660W, 400V, 200Hz, 12,000 RPM,
30° swiveling
Note:
The technical data and descriptions are copies of the original order

Iklan ini diterjemahkan secara otomatis. Kesalahan terjemahan mungkin terjadi.