111A

MACPRESSE EUROPA S.R.L. 111A

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2012, jam operasional: 25.895 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 78 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.500 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 600 kg, berat keseluruhan: 24.000 kg, kapasitas tangki oli: 1.000 l, daya: 55 kW (74,78 hp), laju aliran volumetrik: 930 m³/jam, Technical Data — Baler: Manufacturer: Presona AB Fodevwlqqspfx Adgspb Type: LP 80 VHK 1 Year of manufacture: 2012 Total operating hours (machine): 25,895 hours (as of July 2025) Effective pump operating hours: 14,135 hours (as of July 2025) Number of bales produced: 235,597 units (as of July 2025) Main press force: 78.5 t Specific pressing force: 95 N/cm² Pre-press force: 28 t Press chamber volume: 2.7 m³ Feed hopper dimensions: 1,500 x 1,100 mm Theoretical throughput: 930 m³/hour Throughput under operating conditions: 410 m³/hour Bale dimensions: 750 x 1,100 mm Drive power: 55 kW Tying: 5-fold vertical, 3-fold horizontal, fully automatic Throughput at bulk density of: 30 kg/m³: approx. 9 to 12 t/hour, material-dependent 50 kg/m³: approx. 14 to 17 t/hour, material-dependent 100 kg/m³: approx. 16 to 25 t/hour, material-dependent Throughput for MSW (Municipal Solid Waste): approx. 20 to 27 t/hour, material-dependent Bale weights: 450 to 600 kg, depending on material and bale length Hydraulic oil tank volume: 1,000 L Baler dimensions (installed with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Transport dimensions (baler only): 10,985 x 2,300 x 2,900 mm Machine weight (baler): approx. 24 t Condition of the baler: The machine has been partially overhauled and serviced in our workshop. After completion of the work, it was tested during live operation, both in manual and automatic mode. The following overhaul work was carried out: - Machine cleaned, partially derusted and partially repainted - Hydraulic oil tank fully drained and cleaned - Oil and air filters replaced, new hydraulic oil filled - Press ram disassembled and cleaned - All four running rollers on the press ram replaced - Wire station with guide rollers for the bottom wire cleaned and made operational - Side guides removed from press ram, smoothed, reinstalled and readjusted - Main hydraulic cylinder removed, dismantled and inspected - Piston rod replaced, cylinder tube honed - Complete seal kit replaced, pressure test performed - Hydraulic hose from main hydraulic cylinder replaced - Vertical and horizontal needle systems for tying disassembled, cleaned, wire guide rollers made operational and maintained - Chain cleaned, lubricated, chain tension readjusted - Drillomat cleaned, wire knives, twister shafts and twister fingers checked, torqued, and serviced - Door contact switches checked and partially replaced - Emergency stop button tested - Complete electrical wiring checked and partially renewed - Bearings of wire guide rollers below the baler replaced - New safety grids for vertical and horizontal tying manufactured and installed - Machine inspected, general maintenance performed and baler tested in manual and automatic operation Scope of delivery: Only the baler is for sale. Remarks: All documentation (operating manual, CE declaration, electrical/hydraulic schematics) is complete and available. An inspection can be arranged by appointment. We assume no liability for technical specifications or possible errors.

Kondisi: belum diuji (bekas), Hydraulic press for compacting paper and similar materials. The machine was fully operational prior to disassembly. Fpjdoh Nyfyjpfx Adgeb Press dimensions: Length: 4850 mm, width: 1370 mm, height: 3000 mm (can be reduced to 2300 mm). Weight approx. 3500 – 4000 kg. For further information, please contact: +48 539 660 495.

Kondisi: belum diuji (bekas), Tahun pembuatan: 1985, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 50 t, panjang bal: 1.000 mm, lebar bal: 750 mm, tinggi bal: 750.750.750 mm, berat bal: 500 kg, tegangan masuk: 400 V, berat keseluruhan: 7.500 kg, kapasitas tangki oli: 500 l, daya: 30 kW (40,79 hp), berat kosong: 7.500 kg, frekuensi input: 50 Hz, Manufacturer: Pal Pacomat V Year of manufacture: 1985 Main press force: 50 t Specific pressing force: 5 kg/cm² Feeding channel: 1,000 x 720 mm (L x W) Theoretical throughput capacity: 200 m³/h Fpjdpfxjic Rl De Adgob Bale size: 700 x 1,000 mm (W x H), length adjustable Drive motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8 t The hydraulic unit is functional, the drive motor is currently removed.

Kondisi: bekas, Tahun pembuatan: 2003, Technical details: Pressing force: 40 t Hopper opening: 1200 x 730 mm Fpsdpfx Aou Nw Ezsdgjb Material: Cardboard, plastic – e.g., PET bottles Voltage: 400 V / 50 Hz Total power requirement: 16.4 kW Transport dimensions (machine): 6.5 x 6.2 x 2.7 m Fully automatic hydraulic CHANNEL BALER for recycling applications – Incl. feed unit/conveyor belt, LxW: 4500 x 1000 mm, motor-driven – Equipped with automatic 3-fold tying unit – Bale counter/display Press chamber (LxWxH): 1800 x 800 x 800 mm with 1.2 m³ volume Bale size (LxWxH): 300–1500 x 800 x 800 mm Bale weight: 250–450 kg, depending on material and bale length Filling opening (LxW): 1200 x 730 mm; Filling height: 1200 mm Hopper size (LxWxH): 1200 x 1200 x 1400 mm; Fill height: 2500 mm

Tahun pembuatan: 2006, Kondisi: hampir baru (bekas), Contenitore con volume di 32 m³ Fpodpfx Adefhb Tkogob

Kondisi: sangat baik (bekas), Tahun pembuatan: 2007, jam operasional: 21.676 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 78 t, lebar bukaan pengisian: 750 mm, panjang bukaan pengisian: 1.500 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 600 kg, berat keseluruhan: 25.000 kg, tinggi transportasi: 3.000 mm, kapasitas tangki oli: 1.000 l, daya: 55 kW (74,78 hp), berat kosong: 25.000 kg, laju aliran volumetrik: 930 m³/jam, tekanan kerja: 250 batang, Hello, Fpedpfxsvgrh Uo Adgeb We hereby offer you, without obligation, a used baler from the manufacturer Presona AB, type LP 80 VH1. The following technical data has been taken from the manufacturer's operating manual and brochures. We cannot guarantee the accuracy or completeness of this information. Manufacturer: Presona AB, Sweden Type: LP 80 VH1 Year of manufacture: 2007 Total operating hours: 21,676 hours (as of November 2024) Pressing force (main press): 78 t Specific pressing force: 95 N/cm² Pre-press lid force: 28 t Feed opening dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank volume: 1,000 l Press dimensions (assembled with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight (press): approx. 25 t Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The baler is in good condition, will remain in operation until January 2025, and can be inspected by appointment. We would be pleased if this machine is of interest to you. Your service team at Mertens & Frowein GmbH

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2005, Tangki penghubung 30-32 m³ untuk kompresor sekrup, tersedia pilihan kanan atau kiri. Tangki penghubung bekas, berfungsi dengan baik Fpodpfx Adsgypd Hogeb mulai dari 4.000 € tergantung kondisi, belum termasuk PPN. Pengiriman tersedia.

Kondisi: baru, Klanke Supercut roll splitter for efficient shredding of waste rolls. Features: - Automatic safety interlock Fsdpen I Rgpsfx Adgspb - Emergency stop pull cord - Siemens PLC Technical specifications: Blade length: 3000 mm Cutting channel opening: 1200 mm Motor power: 15 kW Cutting force: 50 t Made to order Price and further information upon request. We would be pleased to provide you with a non-binding offer.

Tahun pembuatan: 2003, jam operasional: 43.000 h, Kondisi: perlu perbaikan (bekas), nomor mesin/kendaraan: HBC 140 2x75kW 2003 (W230-005), nl-naar-en Fpedpfx Ajkcgynsdgsb

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2007, jam operasional: 22.605 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 100 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.600 mm, lebar bal: 1.100 mm, tinggi bal: 1.100 mm, berat bal: 1.400 kg, arus masuk: 238 A, berat keseluruhan: 36.000 kg, kapasitas tangki oli: 1.300 l, For sale is a refurbished baler with 100 t press force, large-format bales 1100 x 1100 mm, 75 kW drive power and 10-way cross-tying. Technical specifications baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main press force: 100 t Pre-press force: 50 t Operating hours: 22,605 h Fpodpsvf E Avsfx Adgob Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Connected load: 126 kW Total current consumption: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput at bulk density of: - 30 kg/m³: approx. 16 t/h - 50 kg/m³: approx. 25 t/h - 100 kg/m³: approx. 47 t/h Bale weight up to 1,400 kg, depending on material and bale length Hydraulic oil tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operating panel: Schneider MAGELIS Touch Baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions without baler: 11,765 x 2,500 x 3,450 mm (L x W x H) Baler weight: approx. 36 t Remarks: The baler has been partially overhauled, serviced in our workshop, and tested after completion of work before being stored. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment works have been carried out: - Descaling and partial repainting of the baler. - Hydraulic oil tank drained, oil and air filters replaced. - New hydraulic oil filled. - All hydraulic hoses renewed. - Main hydraulic cylinder, two cylinders of the pre-press flap and the channel cylinder disassembled, dismantled, inspected, cylinder tubes honed, all seal kits replaced and final pressure tested. - Pre-press flap with bearings and bearing blocks disassembled. First and third circular arc segments removed and newly welded in. - Both shaft bearings for the pre-press flap renewed. - Upper material guide on the frame for the pre-press flap renewed. - Plunger disassembled, inspected and both front roller guides renewed. - Material guides and wear strips at the sides and on the bottom of the plunger cut out and newly welded in. - Horizontal and vertical needle and tying units disassembled, dismantled, inspected, plastic slide plates, bearings on twister shafts, and wire divert rollers with bearings in the needle heads renewed. - Both bronze slide rails left and right in the frame cover for the plunger renewed. - Both wire divert units left and right, including bale retaining clamps, fully renewed. - Wire infeed unit including hydraulic cylinder below the needle passes fully renewed. - Wire mark/scoring in the bottom and sidewalls of the channel welded up and smoothed. - General maintenance and service work carried out in line with manufacturer specifications. - Baler tested in manual and automatic mode, accepted and stored after completion of refurbishment works. We assume no liability for the technical details or possible errors.