S-60K (6)

Riko Ekos d.o.o S-60K (6)

Kondisi: bekas, System: Inclined Clarifier, Lamella Clarifier, Lamella Separator Condition: Used, up to 120 m³/h depending on medium Design: Robust, high-performance construction Material: Stainless steel on container frame, 30' container, scraper plates in PP (polypropylene) Dimensions (LxWxH): 7580 x 2435 x 3000 mm Weight: approx. 8,000 kg Principle: Wastewater is fed into the inlet of the inclined clarifier and flows downward. Due to the arrangement of the lamella plates in the clarifier, the wastewater is redirected underneath the plates and flows upward through the lamellas. As a result, solids settle down onto the lamella plates. The clarified water is transported to the outlet. Solids on the lamella plates gradually slide down along the plates, where the sludge hopper is located. Laodpfx Aasppyhtshjk Rake Mechanism: Optionally, we offer the inclined clarifier with a rake mechanism to keep the sludge fluid. Application: Separation of solids and liquids by sedimentation. Inclined clarifiers are often used as a pre-stage before filter presses or decanters for thickening. Pre-thickening of thin sludge allows the filter press to be sized smaller in terms of filter area. The system is in good condition and available for rent or sale. Inspection at our plant is possible by appointment. We also offer new inclined clarifiers with a delivery time of approximately 8 to 10 weeks!

Kondisi: baru, Bunker conveyor system suitable for feeding presses, shredders, etc. Delivery possible throughout Europe. Technical data: Pos. 1 Feed hopper Pos. 2 Feed belt 1.5 kW, belt width: 1100 mm, axle spacing: 3500 mm Pos. 3 Inclined conveyor 1.1 kW, belt width: 1100 mm, axle spacing: 4700 mm Lodpfedxwlqex Aahsak Standard discharge height: 2800 mm (can be increased with spacer feet as shown in the illustration) Made to order Further information and data available upon request

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2012, jam operasional: 25.895 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 78 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.500 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 600 kg, berat keseluruhan: 24.000 kg, kapasitas tangki oli: 1.000 l, daya: 55 kW (74,78 hp), laju aliran volumetrik: 930 m³/jam, Technical Data — Baler: Manufacturer: Presona AB Type: LP 80 VHK 1 Year of manufacture: 2012 Total operating hours (machine): 25,895 hours (as of July 2025) Effective pump operating hours: 14,135 hours (as of July 2025) Number of bales produced: 235,597 units (as of July 2025) Main press force: 78.5 t Specific pressing force: 95 N/cm² Pre-press force: 28 t Press chamber volume: 2.7 m³ Feed hopper dimensions: 1,500 x 1,100 mm Theoretical throughput: 930 m³/hour Throughput under operating conditions: 410 m³/hour Bale dimensions: 750 x 1,100 mm Drive power: 55 kW Tying: 5-fold vertical, 3-fold horizontal, fully automatic Throughput at bulk density of: 30 kg/m³: approx. 9 to 12 t/hour, material-dependent 50 kg/m³: approx. 14 to 17 t/hour, material-dependent 100 kg/m³: approx. 16 to 25 t/hour, material-dependent Throughput for MSW (Municipal Solid Waste): approx. 20 to 27 t/hour, material-dependent Bale weights: 450 to 600 kg, depending on material and bale length Hydraulic oil tank volume: 1,000 L Baler dimensions (installed with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Transport dimensions (baler only): 10,985 x 2,300 x 2,900 mm Machine weight (baler): approx. 24 t Condition of the baler: The machine has been partially overhauled and serviced in our workshop. After completion of the work, it was tested during live operation, both in manual and automatic mode. The following overhaul work was carried out: - Machine cleaned, partially derusted and partially repainted - Hydraulic oil tank fully drained and cleaned - Oil and air filters replaced, new hydraulic oil filled - Press ram disassembled and cleaned - All four running rollers on the press ram replaced - Wire station with guide rollers for the bottom wire cleaned and made operational - Side guides removed from press ram, smoothed, reinstalled and readjusted - Main hydraulic cylinder removed, dismantled and inspected - Piston rod replaced, cylinder tube honed - Complete seal kit replaced, pressure test performed - Hydraulic hose from main hydraulic cylinder replaced - Vertical and horizontal needle systems for tying disassembled, cleaned, wire guide rollers made operational and maintained - Chain cleaned, lubricated, chain tension readjusted - Drillomat cleaned, wire knives, twister shafts and twister fingers checked, torqued, and serviced - Door contact switches checked and partially replaced - Emergency stop button tested - Complete electrical wiring checked and partially renewed - Bearings of wire guide rollers below the baler replaced - New safety grids for vertical and horizontal tying manufactured and installed - Machine inspected, general maintenance performed and baler tested in manual and automatic operation Scope of delivery: Only the baler is for sale. Remarks: Lsdpfxsvwlqqe Aahsak All documentation (operating manual, CE declaration, electrical/hydraulic schematics) is complete and available. An inspection can be arranged by appointment. We assume no liability for technical specifications or possible errors.

Kondisi: siap digunakan (bekas), Mesin Press Balok Hsm HL 4809 LI - Bukaan pengisian besar, ideal untuk kotak berukuran besar - Dump kontainer untuk pengisian yang nyaman Tekanan dalam kN: 480 - Tegangan/frekuensi: 3 x 400 V / 50 Hz Lajdpfxora Dddo Aahjk - Berat balok dalam kg (tergantung material): hingga 400 kg - Dimensi balok (panjang x lebar x tinggi dalam mm): 1200 x 1100 x 750 - Dimensi mesin (panjang x lebar x tinggi dalam mm): 5648 x 1849 x 2515 Waktu siklus kosong dalam detik: 53 - Pengikatan manual: 4 kali dengan kawat

Tahun pembuatan: 2003, jam operasional: 43.000 h, Kondisi: perlu perbaikan (bekas), nomor mesin/kendaraan: HBC 140 2x75kW 2003 (W230-005), nl-naar-en Ljdpfx Aajkcgynjhoak

Kondisi: sangat baik (bekas), Fungsionalitas: berfungsi sepenuhnya, Technical specifications for the document shredding plant: Manufacturer: HSM GmbH + Co KG General information on the two-stage shredder system: Type: Duo Shredder 5750 Year of manufacture: 2015 Operating hours: 3,093 hours Throughput capacity: up to 800 kg/hour, depending on material Rated power: 30 kW Rated current: 62 A Particle size: 6 x 40 - 53 mm Fuse protection: 63 A gG/gL/C/K Shredder weight: approx. 2,500 kg Pre-shredder data: Shredder type: V 570 Working width of cutting unit: 500 mm Particle size: 20 x 155 mm (W x L) Rated power pre-shredder: 2 x 5.5 kW Rated current pre-shredder: 2 x 11.5 A Secondary shredder data: Shredder type: P 500.2 Working width of cutting unit: 500 mm Particle size: 6 x 40 – 53 mm (W x L) Rated power secondary shredder: 9.2 kW Rated current secondary shredder: 18 A Security level per DIN 66399: P-3, O-2, T-3, E-2 Laedpfx Aowrybrsahok Baler data: Type: KP 100.1 Year of manufacture: 2015 Operating hours: 2,377 hours Pressing force: 9 - 12 t Bale weight: 40 – 150 kg/bale, material-dependent Cycle time: 7 – 16 seconds Feed opening dimensions: 450 x 580 mm Bale dimensions: 630 x 500 x 400-1000 mm (W x H x L) Binding: triple, horizontal Baler dimensions: 3990 x 2225 x 1735 mm (L x W x H) Baler weight: approx. 1,000 kg Overall system dimensions (conveyor belt, shredder, and baler): 9560 x 2071 x 3550 mm (L x W x H) Functional description: This is a complete system consisting of a feed conveyor belt, a two-stage shredding system, and a horizontal baler. Material is fed via the conveyor belt, shredded in two steps, and subsequently pressed into stackable bales. A second cutting unit and various motors are available as spare parts for the system. Comments: Complete documentation (operating instructions, electrical/hydraulic circuit diagrams) is available. Inspection by appointment is possible. No liability is assumed for technical information or possible errors.

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2005, Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: 0509, de Lodpfjwnx Ngex Aahjak

Kondisi: siap digunakan (bekas), Tahun pembuatan: 2002, Speed: 4500 rpm, max. drum diameter: 300 mm / 167 mm, solids: 2.6 kg/dm³, material temperature min./max.: 5°C / 100°C, bowl dimensions X/Y: 300 mm / 1200 mm, machine material: stainless steel, operating hours: 62,293 h. Spare parts included. An on-site inspection is possible. Lajdpeu Av H Dsfx Aahsk

Kondisi: sangat baik (bekas), Tahun pembuatan: 2006, Balemaster Year: 2006 Type: CMG 268 Waste baler Ljderdwlkjpfx Aahoak

Kondisi: sangat baik (bekas), Tahun pembuatan: 2006, jam operasional: 2.632 h, Fungsionalitas: berfungsi sepenuhnya, nomor mesin/kendaraan: 29.381, gaya penekanan: 35 t, lebar bukaan pengisian: 620 mm, panjang bukaan pengisian: 1.000 mm, lebar total: 2.380 mm, tinggi total: 2.500 mm, panjang total: 6.625 mm, Termasuk sabuk pengumpan. Mesin siap digunakan segera. Ljdpovaw T Aofx Aaheak