Beli Romer bekas (124)

Tahun pembuatan: 2020, Kondisi: baru, Gravity Heating System Thanks to the use of a gravity heating system in the SPARK series gravity ovens, we can boast of excellent temperature uniformity. Our tests have shown that, with proper arrangement of the components, the air temperature uniformity in our gravity ovens does not exceed ± 5 °C! We owe this result to our heater mounting technology. Rapid Heating Tjdofy T R Dspfx Aatof The SPARK series gravity ovens are equipped with specially designed heaters that emit heat quickly, enabling our ovens to reach operating temperatures rapidly. This fast heat-up is due to the applied seals and insulation. The specially profiled seal is asbestos-free and user-safe. Through optimized insulation – ensuring no contact between the oven chamber and its housing – heat loss is minimized and energy is conserved. Depending on the model, our ovens can heat up to 8 °C per minute. Transport System SPARK series ovens are equipped as standard with two floor transport trolleys. In response to market demand for cost-effective solutions, we have developed a manual floor transport system that allows large items to be moved with minimal effort. Our system enables optimum utilization of the oven’s entire surface while ensuring a high level of cleanliness of the coated parts. Thanks to the use of two trolleys, the trolley traveling in the hall does not contaminate the oven’s interior. The upper trolley is used for entry into the oven. Using a single trolley would transfer dirt from the shop floor into the oven chamber. Our system eliminates this problem.

Tahun pembuatan: 2020, Kondisi: baru, Touch delete ROMER cabins are equipped with 4-inch color touch lights. The cabin interface is intuitive and available in three operating modes: automatic (temporary), automatic (via plug-in filter cartridge), or manual. Filter Cartridge Sensor The cabins are equipped with a sensor that detects filter clogging and prompts cleaning. The system also notifies when the filters have already been used. Automatic Filter Cleaning The electronic system for automatic filter cleaning controls both the cleaning intervals and the burn-off timing. Each filter is cleaned individually, and filters can also be cleaned manually using presses. From experience, we know it can be difficult to rely on the operator to clean the filters. Thanks to this system, the operator no longer needs to intervene manually. Low Noise Level Aluminum fans are very quiet, operating within a range of 74-79 dB. Tsdpfx Ajfzktzjatjf Even with standard cabin design, it is difficult to hold a conversation due to the quiet operation. Boilers are separated from the cabin. Hanging “squirrel cage” design inside the cabin improves workflow, allowing painters to work without manual handling. Early booking of construction recommended. All remaining cabins are designed to prevent the rise of explosive mixtures during the painting process. Every subcomponent has been carefully selected to minimize this risk.

Tahun pembuatan: 2020, Kondisi: baru, ROMER cabins are equipped with four-inch color touchscreens. The cabin operation is intuitive and can be controlled in three modes: automatic (timer-based), automatic (triggered by a clogged filter sensor), or manual. Automatic Filter Cleaning The electronic system for automatic filter cleaning features an adjustable range for cleaning frequency and burn-off timing. Each filter is cleaned individually, and the filters can also be cleaned manually at the touch of a button. From experience, we know that it is often difficult for operators to carry out regular filter cleaning. Thanks to this system, the operator no longer has to worry about it. Aluminum fans are very quiet, operating at 74-79 dB—which is not much. Tedjfz Atbjpfx Aatsf It is difficult to have a conversation, even with a standard cabin configuration. Browse through the cabin By moving the lifting rails inside the cabin, the work efficiency is improved and relieves the operator from having to move them manually.

Tahun pembuatan: 2020, Kondisi: baru, Pneumatic connection 1" • Controls the 7" color touch panel • Paint tank capacity: 6-7 kg • Air consumption during painting: 15 Nm³/h • Air consumption for cleaning: 350 Nm³/h • Hopper dye sensor: Yes • Ultrasonic screener: Yes • Powder injectors: up to 12 units Description: • RP-01 pump for refilling paint with fresh paint from cardboard • Two operating modes: paint recovery with mixing or total waste • Sealed fluidizing paint container Tjdpfx Aefz Dkgoatof • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor • Automatic tray refilling with paint from cardboard • Paint level sensor in refill box • An acoustic alarm warns the operator when the cardboard paint supply is low • The center is connected to the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Tahun pembuatan: 2020, Kondisi: baru, • Electrical data: 22 kW, 380-400 V, 50-60 Hz • Theoretical capacity: 12,000 m³/h • 1/4" pneumatic connection • Number of filters: 8 pcs. • Filter area: 160 m² • Automatic filter cleaning • Air consumption max. 12 L, 6-8 bar per shot • 50 L waste container capacity Tedpfsfz Dqfsx Aatef Description • Dust collector equipped with a high-efficiency radial impeller • Two operating modes – Full Power and ECO • The basic weight of the filter media used is up to 260 g/m² • High suction performance with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter features its own solenoid valve

Tahun pembuatan: 2020, Kondisi: baru, Washing machines and ultrasonic cleaning baths for washing, phosphating, chromating, degreasing, and removing paint coatings Materials ROMER ultrasonic cleaning systems use stainless steel to provide protection against acids. The tanks feature an additional insulation layer to prevent heat loss and enable faster heating. High-quality materials ensure long service life of the vibrating elements. Heating system The heating elements used in ROMER tanks are made from top-grade materials and high-temperature resistant ceramic components. The heating system ensures high thermal efficiency, with hot water automatically mixing with cold water to heat the entire tank evenly. Tjdpofz Dtzefx Aatjf Ultrasonic transducers The ultrasonic elements used in ROMER cleaning machines are installed in immersion modules, which better reflect vibrations and are replaceable. The ultrasonic frequency range is 20–40 kHz depending on the item being cleaned; lower frequencies are used for large, robust parts and higher frequencies for jewelry, delicate mechanical systems, etc. All transducers are connected by high-temperature resistant cables.

Tahun pembuatan: 2020, Kondisi: baru, • PLC Microprocessor Control • HMI Control Panel • Phases can be changed manually or automatically – temporarily • Two separate circuits for water and chemicals, closed-loop system • Intelligent control – prevents fluid mixing in the event of power failure or sudden shutdown The control box features IP54 technology Tedpfxofz Dvvo Aatjf User manual, declaration of conformity, 12-month warranty. ROMER high-pressure cleaners use sheets that protect against chemicals. The washing walls provide splash protection, and thanks to the closed chemical circuit, the process can be carried out with minimal chemical usage. Due to the small amount of refrigerant required, it is easy to heat and cheaper to purchase. Additionally, you can wash large components that cannot be cleaned in standard tanks. Filtration system Thanks to the filtration system, the chemicals operate in a closed loop; three different filters of varying thickness are used to prevent debris and grease from entering the circuit. The chemicals are stored in heated stainless steel tanks and are pumped under pressure to the lance. Washing dimensions The high-pressure cleaner allows for washing large items and optionally features a rotating platform to turn the cleaned items; components can be loaded onto it by forklift or crane. High-pressure pumps The wash system consists of two preparation stages. Both processes have separate sets of pipes, pumps, wires, and spray guns to minimize mixing of agents during phase change. The drains have separate valves to manage liquid return. The wash system is equipped with a logic controller that manages all components. Chemicals are supplied by a highly durable, acid-resistant, multi-stage AISI304 pump (3 kW, up to 20 bar). The rinse phase uses a high-pressure piston pump with ceramic pistons (3 kW), delivering 160–200 bar.

Tahun pembuatan: 2020, Kondisi: baru, DESCRIPTION The so-called partial demineralized water is produced from the demineralized water station using ion exchange technology. The station consists of 3 columns: - Strongly acidic cation exchanger operating in the sodium cycle - Strongly basic anion exchanger operating in the chloride cycle Tsdpfxefz I Nhe Aatef - Carbon filter Our demineralization stations RDI-2 / RDI-4 are equipped with fully automatic control heads. The columns are made of AISI316L stainless steel.

Tahun pembuatan: 2020, Kondisi: baru, 7" Touch Panel The large color touchscreen panel is aesthetically pleasing and offers comfortable, intuitive operation. You can configure all essential parameters directly on it. Storage for 20 Programs with 10 Events Each It is possible to store up to 20 programs and activate up to 10 consecutive time-temperature events, arranged within the heating curve. This is particularly required for more demanding processes. Gas/Oil Consumption Data Consumption is calculated based on the burner settings. This function allows you to estimate the cost of a specific cycle, plan consumption, and monitor staff. Dual-channel Recorder with USB Cycle Parameters Every furnace is equipped with a recorder that logs all ignition parameters, including two temperature channels—just like a flight data recorder—onto a USB stick. Todpsfz I Rxefx Aatsf

Tahun pembuatan: 2020, Kondisi: baru, DESCRIPTION The so-called semi-deionized water is produced from the demineralized water station using ion exchange technology. The station consists of 3 columns: - Strongly acidic cation exchanger operating in the sodium cycle, - Strongly basic anion exchanger operating in the chloride cycle, - Carbon filter Our RDI-2 / RDI-4 demineralization stations are equipped with fully automatic control heads. Piping Tjdpfefz I Syjx Aatef The columns are made of AISI316L stainless steel.

Tahun pembuatan: 2020, Kondisi: baru, ROMER® specializes in manufacturing individual technological devices for powder coating systems as well as complete, fully-automatic turnkey coating lines. ROMER® offers heating solutions for the aerospace and automotive industries, serving some of the world’s largest companies. We provide warranty and post-warranty service for all devices we sell, including a complete range of spare parts. A coating applied to a poorly pre-treated surface will peel off or corrode after a short period of time. Ensuring top-quality coating essentially starts with proper degreasing – the foundation of every paint job. Coating on inadequately degreased parts will peel off very quickly. After degreasing, the next step is to abrade the surface coating of the part, which improves paint adhesion—for example, when bending sheet metal—and to apply protective layers, such as a phosphate coating, which further enhances corrosion resistance. There are many solutions to address the aforementioned issues. But what is the most important thing in a powder coating workshop? You might think it’s the applicator, but that’s not the case; even the best applicator cannot help if your oven has poor temperature distribution. Areas where the component is overheated will cause discoloration, and in under-heated areas, the coating will not adhere properly. Above all, the oven is the most crucial aspect. Oil, gas, or electric oven? Not sure how to power your oven? Which method is more cost-effective? What does each method involve? What are the running costs? We will try to answer your questions. Depending on customer requirements, conveyor systems can be floor-mounted or suspended from rails. Tjdpfxjfz Ndys Aatsf - For user-friendly solutions in manual systems, we recommend suspended transverse overhead conveyors (cross-transfer systems). - In automated systems, chain conveyors are most commonly used, as they operate continuously. These are an excellent solution for companies that require process quality and repeatability. - For companies producing different components simultaneously — for example, using multiple booths with different colors — flexible solutions employing power-and-free conveyors are used. This, however, is the most expensive option.

Tahun pembuatan: 2020, Kondisi: baru, Automatic car wash systems are a solution designed to help you reduce costs, improve quality, and increase the efficiency of surface preparation processes. The automatic car wash station is equipped with a set of spray pumps. It is engineered to minimize fluid carryover between sequential process steps, reducing expenses and enhancing wash quality. This is particularly important because any apparent savings made by using systems without such solutions can result in significantly higher future costs due to increased chemical usage and waste disposal, as well as challenges in maintaining required bath parameters. Todsfy T Szspfx Aatef Our research and development efforts have enabled us to develop a car wash system with an optional parts drying feature, utilizing hot air blown by a series of fans post-wash. The car wash station is fitted with an advanced macro-programming system, allowing users to create custom wash programs—up to 10 steps per tank—tailored to your process requirements. Program steps can be repeated or rearranged as needed. Each tank is represented by its own unique symbol and name for intuitive operation by the user. Optionally, tanks can be equipped with automated bath replenishment systems, which can refill liquid either after each process stage or at the end of the cycle. • Control panel mounted on a swing arm for improved accessibility • PLC microprocessor control • 7'' touchscreen interface • Significantly higher number of nozzles compared to conventional systems • (Optional) Possibility to dry parts after washing • Customizable advanced programming capability • Advanced damper system made of acid-resistant sheet metal, double-secured with limit switches • Monitoring system for tight sealing and opening of the main flap • Dedicated pipework, nozzles, and tanks for each stage to prevent liquid cross-contamination • Intelligent control – prevents fluid mixing in the event of power failure or emergency stop • Fully automatic operation Pricing information is available in the catalog.

Tahun pembuatan: 2020, Kondisi: baru, 7-inch Touch Panel The large color touch panel makes parameter input even easier and more convenient. 5 Programs with 50 Steps Each You can program up to 5 heating curves, each with a maximum of 50 steps. This feature is especially useful for complex processes. Information about Gas and Oil Consumption Oil and gas consumption is calculated based on the burner settings. This function allows you to estimate fuel consumption and the overall operating costs. USB Memory Every firing process is logged, and the process data can be transferred to a USB stick for evaluation on a PC. Each file is automatically created and corresponds to a single firing process, recording peak temperatures and exact times. The file is saved in *.csv format (Excel spreadsheet). This option is free for all buyers until the end of 2016; with other manufacturers, this can cost several thousand euros. Storage of the Last 20 Firing Processes Problem with a batch? Not enough components coming out of the oven? Now you can review the precise parameters of the firing process—such as duration or potential issues. New! Timer Function You can set the start time so that the oven powers up automatically before the workday begins. Built by professionals for professionals. Automatic Exhaust System The exhaust system can be programmed to open a few minutes before the firing process ends, allowing the smoke to be removed from the chamber. The exhaust system can be controlled via the touch panel. Process Duration Timer Heating dynamics are used to calculate the process duration. The display shows when the firing process will end. Self-Closing Doors To open, simply pull the door. To close, just push gently—the door will close automatically. Exhaust Hood Above the Door (optional) To minimize heat loss in the production hall when opening the door, an exhaust hood above the door extracts hot air. Partition (optional) The partition is suitable for large ovens when you want to use only parts of the oven. The oven is equipped with a movable divider and special control system. 2-in-1 (optional) It's possible to use both chambers independently—for example, running the firing process in the first chamber while drying occurs in the second. Tsdofzb Rcspfx Aatsf

Tahun pembuatan: 2020, Kondisi: baru, 7" Touch Panel Tsdpfx Aaefz Anpotof The large color touchscreen panel is aesthetically pleasing and offers comfortable, intuitive operation. You can configure all essential parameters directly on it. Storage for 20 Programs with 10 Events Each It is possible to store up to 20 programs and activate up to 10 consecutive time-temperature events, arranged within the heating curve. This is particularly required for more demanding processes. Gas/Oil Consumption Data Consumption is calculated based on the burner settings. This function allows you to estimate the cost of a specific cycle, plan consumption, and monitor staff. Dual-channel Recorder with USB Cycle Parameters Every furnace is equipped with a recorder that logs all ignition parameters, including two temperature channels—just like a flight data recorder—onto a USB stick.

Tahun pembuatan: 2020, Kondisi: baru, • PLC Microprocessor Control • HMI Control Panel • Phases can be changed manually or automatically – temporarily • Two separate circuits for water and chemicals, closed-loop system • Intelligent control – prevents fluid mixing in the event of power failure or sudden shutdown The control box features IP54 technology User manual, declaration of conformity, 12-month warranty. ROMER high-pressure cleaners use sheets that protect against chemicals. The washing walls provide splash protection, and thanks to the closed chemical circuit, the process can be carried out with minimal chemical usage. Due to the small amount of refrigerant required, it is easy to heat and cheaper to purchase. Additionally, you can wash large components that cannot be cleaned in standard tanks. Filtration system Tjdpefz Ax Ssfx Aatef Thanks to the filtration system, the chemicals operate in a closed loop; three different filters of varying thickness are used to prevent debris and grease from entering the circuit. The chemicals are stored in heated stainless steel tanks and are pumped under pressure to the lance. Washing dimensions The high-pressure cleaner allows for washing large items and optionally features a rotating platform to turn the cleaned items; components can be loaded onto it by forklift or crane. High-pressure pumps The wash system consists of two preparation stages. Both processes have separate sets of pipes, pumps, wires, and spray guns to minimize mixing of agents during phase change. The drains have separate valves to manage liquid return. The wash system is equipped with a logic controller that manages all components. Chemicals are supplied by a highly durable, acid-resistant, multi-stage AISI304 pump (3 kW, up to 20 bar). The rinse phase uses a high-pressure piston pump with ceramic pistons (3 kW), delivering 160–200 bar.

Tahun pembuatan: 2020, Kondisi: baru, ROMER is also involved in the production of overhead conveyor systems. Cross traverses (cross transport) are specially designed and manufactured for certain installations. Below are some examples of equipment: conveyor systems. Depending on customer requirements, the conveyor systems can either be floor-mounted or suspended from rails. Todpfxefz Dibo Aatof - For convenient solutions in manual installations, we recommend suspended cross beams (cross transport). - For automated systems, chain conveyors are most commonly used; these run continuously without stopping and are an excellent solution for companies focused on process quality and repeatability. - For businesses that manufacture different products simultaneously or have several booths for various colors, flexible solutions using a gravity conveyor are implemented—this is the most expensive solution.

Tahun pembuatan: 2020, Kondisi: baru, Transport systems Depending on the customer's requirements, transport systems can be either floor-based or suspended from rails. - For convenient solutions in manual installations, we recommend suspended cross-transfer systems (lateral transport). - In automated systems, chain conveyors are most commonly used. These systems operate continuously without stopping, making them an excellent solution for businesses focused on process quality and repeatability. Tsdpfefz Dt Nex Aatef - For companies manufacturing a variety of products simultaneously, such as those with multiple booths for different paint colors, flexible solutions using power-and-free conveyors are implemented. This is the most expensive option. All installations are custom-made according to customer requirements. Continuous suspended chain transport systems are designed and manufactured to the client’s specifications. Within this system, it is also possible to provide floor conveyor systems to transport items such as flowerpots or rims (see photo). ROMER also manufactures suspended transport systems. Cross-transfer units are engineered and built to meet the demands of specific installations. Photoelectric cell application The use of a photoelectric cell in the detail zone allows for measurement of the part’s length, enabling the automatic activation of spray guns when the part is within range and their immediate deactivation after coating. The photoelectric cell is supplied as standard equipment. Detailed recognition using special markers. Above the carrier there are plates with identification holes. In conjunction with the photoelectric cell, the PLC controller identifies coated workpieces, turning the spray guns on and off at the correct times—saving both energy and powder. Vertical shape detection. By using light barriers with horizontal sensors, the PLC controller can also analyze the vertical shape of a component. The PLC controller times the appearance of the part in the gun zone, allowing for selective activation or deactivation of spray guns. With multi-sensor horizontal and vertical light barriers, This solution enables precise measurement of workpiece dimensions, allowing for the control of manipulators as well.

Tahun pembuatan: 2020, Kondisi: baru, Transport systems Depending on the customer's requirements, transport systems can be either floor-based or suspended from rails. - For convenient solutions in manual installations, we recommend suspended cross-transfer systems (lateral transport). - In automated systems, chain conveyors are most commonly used. These systems operate continuously without stopping, making them an excellent solution for businesses focused on process quality and repeatability. - For companies manufacturing a variety of products simultaneously, such as those with multiple booths for different paint colors, flexible solutions using power-and-free conveyors are implemented. This is the most expensive option. All installations are custom-made according to customer requirements. Continuous suspended chain transport systems are designed and manufactured to the client’s specifications. Within this system, it is also possible to provide floor conveyor systems to transport items such as flowerpots or rims (see photo). ROMER also manufactures suspended transport systems. Cross-transfer units are engineered and built to meet the demands of specific installations. Photoelectric cell application The use of a photoelectric cell in the detail zone allows for measurement of the part’s length, enabling the automatic activation of spray guns when the part is within range and their immediate deactivation after coating. The photoelectric cell is supplied as standard equipment. Detailed recognition using special markers. Todpfx Aaefz I D Djtsf Above the carrier there are plates with identification holes. In conjunction with the photoelectric cell, the PLC controller identifies coated workpieces, turning the spray guns on and off at the correct times—saving both energy and powder. Vertical shape detection. By using light barriers with horizontal sensors, the PLC controller can also analyze the vertical shape of a component. The PLC controller times the appearance of the part in the gun zone, allowing for selective activation or deactivation of spray guns. With multi-sensor horizontal and vertical light barriers, This solution enables precise measurement of workpiece dimensions, allowing for the control of manipulators as well.

Tahun pembuatan: 2020, Kondisi: baru, Transport systems Depending on the customer's requirements, transport systems can be either floor-based or suspended from rails. - For convenient solutions in manual installations, we recommend suspended cross-transfer systems (lateral transport). - In automated systems, chain conveyors are most commonly used. These systems operate continuously without stopping, making them an excellent solution for businesses focused on process quality and repeatability. - For companies manufacturing a variety of products simultaneously, such as those with multiple booths for different paint colors, flexible solutions using power-and-free conveyors are implemented. This is the most expensive option. All installations are custom-made according to customer requirements. Continuous suspended chain transport systems are designed and manufactured to the client’s specifications. Within this system, it is also possible to provide floor conveyor systems to transport items such as flowerpots or rims (see photo). ROMER also manufactures suspended transport systems. Cross-transfer units are engineered and built to meet the demands of specific installations. Photoelectric cell application The use of a photoelectric cell in the detail zone allows for measurement of the part’s length, enabling the automatic activation of spray guns when the part is within range and their immediate deactivation after coating. The photoelectric cell is supplied as standard equipment. Detailed recognition using special markers. Tjdpfx Aofz I Edeatjf Above the carrier there are plates with identification holes. In conjunction with the photoelectric cell, the PLC controller identifies coated workpieces, turning the spray guns on and off at the correct times—saving both energy and powder. Vertical shape detection. By using light barriers with horizontal sensors, the PLC controller can also analyze the vertical shape of a component. The PLC controller times the appearance of the part in the gun zone, allowing for selective activation or deactivation of spray guns. With multi-sensor horizontal and vertical light barriers, This solution enables precise measurement of workpiece dimensions, allowing for the control of manipulators as well.

Tahun pembuatan: 2020, Kondisi: baru, Touch delete ROMER cabins are equipped with 4-inch color touch lights. The cabin interface is intuitive and available in three operating modes: automatic (temporary), automatic (via plug-in filter cartridge), or manual. Filter Cartridge Sensor Todpfjfz I Ehjx Aatof The cabins are equipped with a sensor that detects filter clogging and prompts cleaning. The system also notifies when the filters have already been used. Automatic Filter Cleaning The electronic system for automatic filter cleaning controls both the cleaning intervals and the burn-off timing. Each filter is cleaned individually, and filters can also be cleaned manually using presses. From experience, we know it can be difficult to rely on the operator to clean the filters. Thanks to this system, the operator no longer needs to intervene manually. Low Noise Level Aluminum fans are very quiet, operating within a range of 74-79 dB. Even with standard cabin design, it is difficult to hold a conversation due to the quiet operation. Boilers are separated from the cabin. Hanging “squirrel cage” design inside the cabin improves workflow, allowing painters to work without manual handling. Early booking of construction recommended. All remaining cabins are designed to prevent the rise of explosive mixtures during the painting process. Every subcomponent has been carefully selected to minimize this risk.

Tahun pembuatan: 2020, Kondisi: baru, Gravity Heating System Thanks to the use of a gravity heating system in the SPARK series gravity ovens, we can boast of excellent temperature uniformity. Our tests have shown that, with proper arrangement of the components, the air temperature uniformity in our gravity ovens does not exceed ± 5 °C! We owe this result to our heater mounting technology. Rapid Heating The SPARK series gravity ovens are equipped with specially designed heaters that emit heat quickly, enabling our ovens to reach operating temperatures rapidly. This fast heat-up is due to the applied seals and insulation. The specially profiled seal is asbestos-free and user-safe. Through optimized insulation – ensuring no contact between the oven chamber and its housing – heat loss is minimized and energy is conserved. Depending on the model, our ovens can heat up to 8 °C per minute. Tjdofz Nd Iopfx Aatof Transport System SPARK series ovens are equipped as standard with two floor transport trolleys. In response to market demand for cost-effective solutions, we have developed a manual floor transport system that allows large items to be moved with minimal effort. Our system enables optimum utilization of the oven’s entire surface while ensuring a high level of cleanliness of the coated parts. Thanks to the use of two trolleys, the trolley traveling in the hall does not contaminate the oven’s interior. The upper trolley is used for entry into the oven. Using a single trolley would transfer dirt from the shop floor into the oven chamber. Our system eliminates this problem.

Tahun pembuatan: 2020, Kondisi: baru, Pneumatic connection 1" • Controls the 7" color touchscreen panel • Color tank capacity: 6-7 kg • Air consumption during painting: 15 Nm³/h • Air consumption for cleaning: 350 Nm³/h • Hopper dye sensor: Yes • Ultrasonic screener: Yes • Up to 12 powder injectors Description • RP-01 pump for refilling paint with fresh paint from cardboard • Two operating modes: paint recycling with mixing or total waste • Sealed fluidizing paint container • Automatic program for cleaning the tank and injection nozzles with compressed air • Hopper powder level sensor • Automatic tray refill with paint from cardboard • Paint level sensor in the refill box Tedpfefz U Sasx Aatof • An acoustic alarm warns the operator when the paint supply in the box is low • The center is connected to the cabin control via the ModBus protocol • Programmable powder suction valve to keep the powder center clean

Tahun pembuatan: 2020, Kondisi: baru, ROMER manipulators are characterized by quiet operation. They are suitable for both simple, widely used processes, as well as complex multidimensional processes. Programming is carried out via a PLC control system. Suitable for work with both long and short strokes. The toothed belt drive ensures a quiet operation. Maintenance-free AC motor. Slim column design for space-saving installation. The robust construction of the manipulators guarantees high performance and stability. The manipulator is equipped with a 7" touch panel, or can be controlled externally via the ModBus protocol using RJ45 cables. Tsdef Aad Njpfx Aatsf

Tahun pembuatan: 2020, Kondisi: baru, 7-inch Touch Panel The large color touch panel makes parameter input even easier and more convenient. 5 Programs with 50 Steps Each You can program up to 5 heating curves, each with a maximum of 50 steps. This feature is especially useful for complex processes. Information about Gas and Oil Consumption Oil and gas consumption is calculated based on the burner settings. This function allows you to estimate fuel consumption and the overall operating costs. USB Memory Every firing process is logged, and the process data can be transferred to a USB stick for evaluation on a PC. Each file is automatically created and corresponds to a single firing process, recording peak temperatures and exact times. The file is saved in *.csv format (Excel spreadsheet). This option is free for all buyers until the end of 2016; with other manufacturers, this can cost several thousand euros. Storage of the Last 20 Firing Processes Problem with a batch? Not enough components coming out of the oven? Now you can review the precise parameters of the firing process—such as duration or potential issues. New! Timer Function You can set the start time so that the oven powers up automatically before the workday begins. Built by professionals for professionals. Tjdpsflk Awsfx Aatsf Automatic Exhaust System The exhaust system can be programmed to open a few minutes before the firing process ends, allowing the smoke to be removed from the chamber. The exhaust system can be controlled via the touch panel. Process Duration Timer Heating dynamics are used to calculate the process duration. The display shows when the firing process will end. Self-Closing Doors To open, simply pull the door. To close, just push gently—the door will close automatically. Exhaust Hood Above the Door (optional) To minimize heat loss in the production hall when opening the door, an exhaust hood above the door extracts hot air. Partition (optional) The partition is suitable for large ovens when you want to use only parts of the oven. The oven is equipped with a movable divider and special control system. 2-in-1 (optional) It's possible to use both chambers independently—for example, running the firing process in the first chamber while drying occurs in the second.

Tahun pembuatan: 2020, Kondisi: baru, Transport systems Depending on the customer's requirements, transport systems can be either floor-based or suspended from rails. - For convenient solutions in manual installations, we recommend suspended cross-transfer systems (lateral transport). Tedpfeflmdwjx Aatjf - In automated systems, chain conveyors are most commonly used. These systems operate continuously without stopping, making them an excellent solution for businesses focused on process quality and repeatability. - For companies manufacturing a variety of products simultaneously, such as those with multiple booths for different paint colors, flexible solutions using power-and-free conveyors are implemented. This is the most expensive option. All installations are custom-made according to customer requirements. Continuous suspended chain transport systems are designed and manufactured to the client’s specifications. Within this system, it is also possible to provide floor conveyor systems to transport items such as flowerpots or rims (see photo). ROMER also manufactures suspended transport systems. Cross-transfer units are engineered and built to meet the demands of specific installations. Photoelectric cell application The use of a photoelectric cell in the detail zone allows for measurement of the part’s length, enabling the automatic activation of spray guns when the part is within range and their immediate deactivation after coating. The photoelectric cell is supplied as standard equipment. Detailed recognition using special markers. Above the carrier there are plates with identification holes. In conjunction with the photoelectric cell, the PLC controller identifies coated workpieces, turning the spray guns on and off at the correct times—saving both energy and powder. Vertical shape detection. By using light barriers with horizontal sensors, the PLC controller can also analyze the vertical shape of a component. The PLC controller times the appearance of the part in the gun zone, allowing for selective activation or deactivation of spray guns. With multi-sensor horizontal and vertical light barriers, This solution enables precise measurement of workpiece dimensions, allowing for the control of manipulators as well.