Kondisi: baik (bekas), Tahun pembuatan: 2012, Fungsionalitas: berfungsi sepenuhnya, Pressing force: 548 kN Gjdpfxjttal Ao Ag Rjuk Load opening size: 1,195 x 650 mm Bale weight depending on material: up to 480 kg Binding with 4x strapping tape or 4x wire Bale size: 1,200 x 780 x max. 1,200 mm Dimensions: 1,797 x 1,062 x 2,985 mm Equipment weight: 2,030 kg

Kondisi: sangat baik (bekas), Tahun pembuatan: 2007, jam operasional: 21.676 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 78 t, lebar bukaan pengisian: 750 mm, panjang bukaan pengisian: 1.500 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 600 kg, berat keseluruhan: 25.000 kg, tinggi transportasi: 3.000 mm, kapasitas tangki oli: 1.000 l, daya: 55 kW (74,78 hp), berat kosong: 25.000 kg, laju aliran volumetrik: 930 m³/jam, tekanan kerja: 250 batang, Hello, We hereby offer you, without obligation, a used baler from the manufacturer Presona AB, type LP 80 VH1. The following technical data has been taken from the manufacturer's operating manual and brochures. We cannot guarantee the accuracy or completeness of this information. Manufacturer: Presona AB, Sweden Type: LP 80 VH1 Year of manufacture: 2007 Total operating hours: 21,676 hours (as of November 2024) Pressing force (main press): 78 t Specific pressing force: 95 N/cm² Pre-press lid force: 28 t Feed opening dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank volume: 1,000 l Press dimensions (assembled with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight (press): approx. 25 t Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The baler is in good condition, will remain in operation until January 2025, and can be inspected by appointment. We would be pleased if this machine is of interest to you. Gedpfx Ajvgrh Ujg Rouk Your service team at Mertens & Frowein GmbH

Kondisi: sangat baik (bekas), Tahun pembuatan: 2019, HSM V-Press 1160 plus Godpfjl Uvukjx Ag Rouk Gaya tekan 532 kN, lebar bukaan masuk 1,195 m, tinggi bukaan masuk 0,65 m, daya penggerak 4 kW, jenis mesin press BP, berat sendiri 2,43 t, panjang transportasi 1,78 m, lebar transportasi 1,568 m, tinggi transportasi 2,995 m, jenis mesin press: baler. Baler siap digunakan segera.

Kondisi: sangat baik (bekas), Tahun pembuatan: 2002, jam operasional: 66.568 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 71 t, lebar bal: 1.100 mm, tinggi bal: 720 mm, berat bal: 600 kg, kapasitas tangki oli: 800 l, daya: 45 kW (61,18 hp), tekanan kerja: 280 batang, en Gedpfx Agoxmk Ive Reuk

Kondisi: baik (bekas), Tahun pembuatan: 1996, Mesin baler termasuk konveyor, keranjang kawat, pembagi Merek: Bollegraaf Tipe: HBC 50A Tahun pembuatan: 1996 Berat sendiri: 19.000 kg Berat ban berjalan: 6.000 kg Daya motor: 30 kW Gusdpfxjxtmyzj Ag Rok Pengikatan vertikal Jumlah kawat: 5

Kondisi: baik (bekas), Tahun pembuatan: 2021, Medium-sized baler, MACFAB, 150A – used - : Price ex location: now only €2,950 instead of €3,900 (net, ex-works) Manufacturer: MACFAB Model: 150 AUTO HT Serial number: MFE1066 Year of manufacture: 2021 Serial number: 167317 Bale dimensions Height: 1,000 mm Width: 975 mm Depth: 800 mm Weight: 150 kg (depending on material) LOADING CHAMBER DIMENSIONS Height: 470 mm Width: 975 mm Depth: 800 mm Machine dimensions Height: 2,630 mm Godpfx Agew D E Uuo Reuk Width: 1,560 mm Depth: 1,030 mm Weight: 780 kg Transport height: 1,955 mm SPECIFICATIONS Power supply: 220 - 240 Volt, single phase Motor: 2.2 kW - 16 Amps Pressing force: up to 8 tonnes Noise emission: 68 decibels Cycle time: 40 seconds A medium-sized vertical baler for compressing cardboard or plastic film into bales weighing up to 150 kg. Ideal for businesses such as supermarkets or retail stores generating a moderate amount of packaging waste. The large upper door opening makes it easy to load waste into the baling chamber. The bales can be easily ejected onto a Euro pallet using the hydraulic bale ejector. This baler features three tying points for securing the bales after compaction. Original list price: €10,802 (net) Condition: good Availability: immediately Location: 68307 Mannheim

Kondisi: baik (bekas), Tahun pembuatan: 2013, Pressing force: 548 kN The dimensions of the feed opening are 1,195 x 650 mm Bale weight depending on material up to 480 kg Tied with 4 x strapping or 4 x wire Bale size: 1,200 x 780 x max. 1,200 mm Gsdpfx Agettav Ne Rouk Dimensions: 1,797 x 1,062 x 2,985 mm The equipment weight is 2,030 kg

Tahun pembuatan: 2006, Kondisi: hampir baru (bekas), Contenitore con volume di 32 m³ Godpfx Aofhb Tkjg Reuk

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2013, Fungsionalitas: berfungsi sepenuhnya, Wet waste compactor press container Bergmann MPB405 SN/10 Gujdpfsvmwpwox Ag Rok suitable for skip loaders 10 m³ usable volume inspected, serviced, fully functional Painting in desired RAL color possible We will be happy to provide a quotation including delivery.

Kondisi: bekas, Tahun pembuatan: 2000, jam operasional: 28.155 h, Baling Press Paal Konti 200 D, year of manufacture 2000, optionally available with matching conveyor belt Paal KEM-1400 Technical data: Manufacturer: Paal Model: Paal Konti 200 D Year of manufacture: 2000 Operating hours: 28,155 Pressing force: 60 t Drive power: 45 kW Total connected load: 60 kW Feed opening: 1020 x 1400 mm Bale dimensions: 750 x 1100 mm, variable length Tying: 4-fold automatic Throughput at: - 35 kg/m³ approx. 9.5 t/h - 60 kg/m³ approx. 16.5 t/h - 100 kg/m³ approx. 26 t/h Bale weight: 450 to 650 kg Transport dimensions: approx. 10123 x 2152 x 2720 mm (LxWxH) Machine weight: approx. 15,000 kg Materials: Paper, cardboard, film The press was dismantled from ongoing operations. Complete documentation available. Please note: All technical data is based on the manufacturer's information. We do not assume any liability for the details provided or any possible errors. The offer is non-binding, subject to prior sale and may be withdrawn at any time. Gujdpfx Aexgp Ibjg Rsk Inspections possible by appointment. Sale is ex works, prepayment required, without warranty or guarantee.

Kondisi: baik (bekas), Tahun pembuatan: 2025, Kontainer pers portal 8m3 sudah direvisi total, selang hidrolik baru, blok pemandu dan silinder baru Merek: Husmann Gjdsxtmviopfx Ag Rjuk Tipe: SPB 8 AN-E Tahun pembuatan: rev. 2025 Pintu pembuangan: engsel atas Mounting: sistem portal

Kondisi: sangat baik (bekas), Tahun pembuatan: 2023, jam operasional: 1.851 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 70 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.400 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, berat bal: 500 kg, berat keseluruhan: 17.000 kg, kapasitas tangki oli: 70 l, Technical data baler: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: AVOS 1410 BS-22/50 Year of manufacture: 2023 Operating hours pump: 1,851 hours (as of July 2024) Pressing force: 70 t (equipped with a 70 t hydraulic cylinder, special equipment) Specific pressing force: 90.9 N/cm² (equipped with a 70 t hydraulic cylinder, special equipment) Feed opening dimensions: 1,400 x 1,000 mm Theoretical cycle time: 13 seconds Theoretical throughput: 266 m³/h Guedpfsu Thbxsx Ag Rsk Bale dimensions: 1,100 x 750 mm (W x H), length variable Drive power: 22 kW Total installed power: 65 kW Tying: 4-fold vertical, fully automatic Throughput rates at a bulk density of: - 30 kg/m³ approx. 5.5 t/h - 50 kg/m³ approx. 7.5 t/h - 100 kg/m³ approx. 9.7 t/h Bale weights with a bale length of approx. 1.2 m: up to 500 kg (material dependent) PLC control: Siemens S7-1500 Operator panel: Schneider Harmony Baler dimensions (assembled): 8,610 x 2,400 x 3,835 mm (L x W x H) Transport weight baler: 17 t Special equipment: - Wear-resistant floor made of HARDOX steel - Larger main hydraulic cylinder with 70 t pressing force - Special press ram for processing loose bulk materials of small grain size - OptiCut XS system for reduced cutting force and increased throughput - Special press ram for compacting "difficult" materials Technical data conveyor belt: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: KGF GB 1500 Year of manufacture: 2023 Drive power: 4.0 kW Belt speed: approx. 0.3 m/s Feed belt length: 2,679 mm Inclined belt length: 6,866 mm Gooseneck length: 1,272 mm Incline: 35° Usable width: 1,400 mm Sidewall height (inclined belt): 800 mm Cleat height: 50 mm Cleat spacing: 750 mm Belt specification: EP 400/3, 3:1 (DIN quality N) Total height: 4,515 mm Transport dimensions (overall): 11,148 x 2,502 mm (L x W) Technical data contactless personnel protection system: Manufacturer: BOREMA Umwelttechnik AG, Switzerland Model: APSS iBOR 22 Year of manufacture: 2023 Condition of the baling line: The entire plant is in very good condition due to its low operating time of only 1,851 pump hours and processing exclusively paper, cardboard, and film. Scope of delivery: - Avermann baler, model AVOS 1410 BS-22/50, incl. wire threading stations and bale chute - Avermann conveyor, model KGF GB 1500 - BOREMA personnel protection system, model APSS iBOR 22 Remarks: Complete documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available. Inspection possible by appointment. No liability is assumed for technical specifications or possible errors.

Kondisi: Pembawa suku cadang rusak (bekas), Tahun pembuatan: 2013, Manufacturer: HSM Gedpfjur Ravsx Ag Rouk Model: HL 4010 Li Year of manufacture: 2013 The equipment is incomplete and is being sold as parts. Defects: - Hydraulic pump missing - Control unit missing - Power supply missing

Kondisi: baik (bekas), Mesin Press Vertikal Dixi 50S PET Tahun pembuatan: 2019-2021 Dimensi balok (P x L x T) (mm): 1200 x 800 x 800 - 1100 Berat balok (kg): sekitar 350-500 kg Data teknis (P x L x T) (mm): 1600 x 1300 x 3100 Lubang pengisian (mm): 1200 x 670 Gaya tekan: 50 ton Daya listrik: 400 V Gusdpfx Agev Amtke Rek

Kondisi: baik (bekas), Tahun pembuatan: 2019, jam operasional: 1.022 h, Fungsionalitas: berfungsi sepenuhnya, Baler Presto CC 20 M, year of manufacture 2019, pressing force 20 t, with retention device. Technical Data: Manufacturer: Presto Model: CC 20 M Year of manufacture: 2019 Operating hours: 1022 Pressing force: 20 t Cycle time: 24 s Drive power: 7.5 kW Feed opening: 1030 x 750 mm Filling volume: 0.53 m³ Tying: 3-fold, manual Throughput (at bulk densities of): 35 kg/m³ - 1.6 t 60 kg/m³ - 2.3 t 100 kg/m³ - 2.8 t Gedpfx Agexfh H Hj Rouk Bale dimensions: 700 x 750 mm Bale weight: up to 300 kg Dimensions: 3300 x 1235 x 1860 mm (LxWxH) Machine weight: approx. 2500 kg Materials: Paper, cardboard, film Remarks: The machine is in good condition. It has been inspected and tested at our location in 28816 Stuhr. A video can be found on our website or YouTube channel. Viewings, including under power, are possible at any time by arrangement. On request, we can also perform tests with your material for a handling fee. We are happy to answer any questions regarding the machine by phone from Monday to Thursday, 8:00 am to 2:00 pm, and on Friday from 8:00 am to 1:00 pm. Please note: All technical data is based on information provided by the manufacturer. We assume no liability for the accuracy of the information or for any errors that may occur. Offers are subject to change and prior sale, and may be revoked at any time. Viewings are possible by appointment. Sale is ex works, without warranty or guarantee.

Kondisi: baik (bekas), Tahun pembuatan: 2019, jam operasional: 673 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 60 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.400 mm, lebar bal: 720 mm, tinggi bal: 1.100 mm, berat keseluruhan: 12.500 kg, kapasitas tangki oli: 800 l, daya: 37 kW (50,31 hp), Technical Data – Baler: Manufacturer: Riko Ekos d.o.o Model: S-60K (5) Gusdpfx Asu Thicjg Rek Year of manufacture: 2019 Operating hours: 673 hours (as of August 2024) Number of bales pressed: 1,127 bales (as of August 2024) Main press force: 60 t Feed opening dimensions: 1,100 x 1,400 mm Filling volume per press cycle: 2.1 m³ Bale dimensions: 720 x 1,100 mm (W x H), length variable Drive power: 37 kW Total connected load: 47 kW Tying: 4-fold horizontal, fully automatic Throughput rates at bulk weight of 30 kg/m³: approx. 5 – 6 t/h 50 kg/m³: approx. 9 – 11 t/h 100 kg/m³: approx. 15 – 19 t/h Hydraulic oil tank volume: 800 L PLC control: Siemens SIMATIC S7-1200 Control panel: Siemens SIMATIC HMI Press dimensions assembled (without hopper and chute): 12,220 x 3,654 x 2,685 mm (L x W x H) Effective transport dimensions, press only (binding system dismantled): 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight (press): 12.5 t Condition of the press: The machine is part of a sorting plant and has only been used intermittently for baling specific material streams. It is no longer required and is therefore being sold. Nevertheless, the baler is started up once a week to press two to three bales to keep the machine in working order. Due to the extremely low operating hours, the baler is in good, ready-to-use condition. Scope of delivery: 1 baler, without conveyor belt, hopper, or chute 8 wire feed stations, without wire 1 bale slide 1 set of machine documentation Remarks: Complete documentation (operating manual, CE declaration, electrical/hydraulic schematic) is available. Inspection possible by appointment. We accept no liability for the accuracy of the technical data or any possible errors.

Kondisi: baik (bekas), Manufacturer: Comp Model: SB5 Motor: 2.2 kW Piston stroke: 500 mm Chamber dimensions: 500 x 350 x 400 mm Godpfxjh Eic Ao Ag Rjuk

Kondisi: baik (bekas), Tahun pembuatan: 2015, jam operasional: 1.932 h, Fungsionalitas: berfungsi sepenuhnya, Baling Press Presto CC 50 M, semi-automatic, year of manufacture 2015, pressing force 50 t, with lifting-tilting device Technical Data: Manufacturer: Presto Model: CC 50 M Year of manufacture: 2015 Operating hours: 1,932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Gedpfx Aoxfh Htsg Rjuk Filling opening: 1030 x 1100 mm Filling volume: 0.85 m³ Tying: 3-fold, wire, manual Throughput capacity at bulk densities of 35 kg/m³ – 1.3 t 60 kg/m³ – 1.7 t 100 kg/m³ – 2.2 t Bale dimensions: 750 x 1100 mm Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (LxWxH) Machine weight: approx. 4,000 kg Materials: Paper, cardboard, film Operating manual available in German. Note: The machine is in good condition. It has been inspected and tested at our site in 28816 Stuhr. The video can be found on our website or YouTube channel. Inspections, including under power, are possible by appointment at any time. On request, we can also perform tests with your material for a handling fee. We are happy to answer any questions regarding the machine by phone from Monday to Thursday between 08:00 and 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data are based on the manufacturer's information. We do not accept any liability for the information provided or for possible errors. This offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by appointment. Sale is ex works against advance payment, without warranty or guarantee.

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 1996, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 170 t, lebar bukaan pengisian: 1.020 mm, panjang bukaan pengisian: 1.800 mm, lebar bal: 1.100 mm, tinggi bal: 1.100 mm, berat keseluruhan: 40.000 kg, kapasitas tangki oli: 3.000 l, tahun perombakan terakhir: 2024, For sale is a used bale press system consisting of a chain belt conveyor designed for below-floor operation, equipped with a feed hopper, a hydraulic pre-compressor with agitating device, a MACPRESSE 111A baler, two complete wire feed frames each with five wire reel stands (without wire). Technical Data – Baler: Manufacturer: MACPRESSE EUROPA S.R.L. Model: 111A Year of manufacture: 1996, overhauled in 10/2024 Main press force: 170 t Specific pressure: 14 kg/cm² Feed chute dimensions: 1,800 x 1,020 mm Fill volume: 2.5 m³ Theoretical throughput: 750 m³/hour Bale dimensions: 1,100 x 1,100 mm, length variable Drive power: 2 x 55 kW Binding: 5-fold horizontal, fully automatic Throughput: approx. 30 to 35 t/hour, material dependent Hydraulic oil tank volume: 3,000 L Transport dimensions (baler with new machine feet): 11,700 x 2,300 x 2,900 mm (L x W x H) Machine weight: approx. 40 t Notes: The baler has been partially overhauled in our workshop and tested upon completion, see our functional video for reference. The system was previously used for baling paper and cardboard from municipal collections. After the contract period ended, the press line became available for sale. Details of overhaul work and replaced spare parts can be found in the detailed photo documentation and our offer. Guodpfx Agju Th D Ro Rek Complete documentation (operating manual, CE declaration, electrical/hydraulic wiring diagrams) is available. Inspection by appointment is possible. We assume no liability for technical details or possible errors. Technical Data – Conveyor: Manufacturer: Wagensfeld B.V. Model: Chain Belt Conveyor 1700 mm Year of manufacture: 2017 Drive power: 7.5 kW Belt speed: 14 m/min Feeder belt length: 6,900 mm Incline belt length: 12,885 mm Gooseneck length: 1,747 mm Total length: 21,271 mm Incline: 32° Usable width: 1,644 mm Height of drive axle above ground: 5,777 mm Side wall height feeder: 500 mm Side wall height incline: 880 mm Steel carrier height: 40 mm Carrier spacing: 1,200 mm Transport dimensions (dismantled): 15,005 x 2,503 x 2,435 mm (L x W x H) Pit dimensions: 11,500 x 2,700 x 1,015 mm (L x W x D) Notes: The chain belt conveyor (year 2017) was custom-built and installed to match the press during the last installation in the Netherlands. The conveyor is in good working condition and was not overhauled. A layout drawing with pit dimensions is available. Scope of delivery: 1 chain belt conveyor by Wagensveld B.V. 1 feed hopper with pre-compression flaps 1 agitating device 1 MACPRESSE baler, type 111A 2 wire feed frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic diagrams

Kondisi: baik (bekas), Tahun pembuatan: 2010, jam operasional: 3.641 h, Fungsionalitas: fungsi terbatas, gaya penekanan: 36 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.080 mm, lebar bal: 1.100 mm, tinggi bal: 750 mm, daya: 15 kW (20,39 hp), berat kosong: 4.000 kg, laju aliran volumetrik: 90 m³/jam, Technical Data – Baler: Gjdpsu Thh Esfx Ag Reuk Manufacturer: Presto GmbH & Co. KG Model: CC 36 M Year of manufacture: 2010 Operating hours: 3,641 hours Main press force: 36 t Specific pressing force: 467 N/cm² Feed opening dimensions: 1,080 x 1,100 mm (L x W) Cycle time: 34 seconds Filling volume per cycle: 0.85 m³ Theoretical throughput: 90 m³/hour Throughput under operating conditions with a material bulk density of 35 kg/m³: approx. 51 m³/hour Bale dimensions: 1,100 x 750 mm (W x H), length variable Drive power: 15 kW Tying: 4-fold vertical, semi-automatic, with polyester twine Throughput rates at a bulk density of: – 35 kg/m³: 1.8 t/hour – 60 kg/m³: 2.5 t/hour – 100 kg/m³: 3.1 t/hour Transport dimensions (baler only): 4,200 x 1,640 x 2,200 mm (L x W x H) Machine weight (baler): approx. 4 t Notes: The baler has been function-tested in our workshop, subsequently stored, and is therefore available at short notice. Full machine documentation (operating manual, CE declaration, electrical and hydraulic schematics) is available. Viewing by appointment possible. No liability is accepted for the accuracy of the technical specifications or any possible errors.

Kondisi: baik (bekas), Tahun pembuatan: 2019, jam operasional: 2.320 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 60 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.400 mm, lebar bal: 720 mm, tinggi bal: 1.100 mm, berat keseluruhan: 12.500 kg, kapasitas tangki oli: 800 l, daya: 37 kW (50,31 hp), Technical Data – Baler: Manufacturer: Riko Ekos d.o.o Model: S-60K (6) Year of manufacture: 2019 Operating hours: 2,320 hours (as of August 2024) Number of bales pressed: 4,359 (as of August 2024) Main press force: 60 t Feed hopper dimensions: 1,100 x 1,400 mm Filling volume / press cycle: 2.1 m³ Gedpfx Aeu Thipeg Reuk Bale dimensions: 720 x 1,100 mm (W x H), length variable Drive power: 37 kW Total connected load: 47 kW Tying: 4-fold horizontal, fully automatic Throughput rates at a bulk density of: - 30 kg/m³: approx. 5–6 t/h - 50 kg/m³: approx. 9–11 t/h - 100 kg/m³: approx. 15–19 t/h Hydraulic oil tank capacity: 800 L PLC control: Siemens SIMATIC S7-1200 Operator panel: Siemens SIMATIC HMI Machine dimensions (assembled, without hopper and chute): 12,220 x 3,654 x 2,685 mm (L x W x H) Effective transport dimensions (press only, with tying system dismounted): 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight: 12.5 t Condition of the baler: The machine is part of a sorting plant and was only partially used for compressing certain material streams. It is now surplus to requirements and is therefore being sold. The baler is, however, operated once per week for two to three bales to ensure it stays functional. Due to the extremely low operating hours, the baler is in good, immediately operational condition. Scope of delivery: - 1 unit baler without conveyor belt, hopper, and chute - 8 units wire feed stations, without wire - 1 unit bale chute - 1 set of machine documentation Remarks: The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagrams) is complete. Inspection is possible by appointment. We accept no liability for technical data or potential errors.

Kondisi: sangat baik (bekas), jam operasional: 2.658 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 71 t, lebar bukaan pengisian: 1.000 mm, panjang bukaan pengisian: 1.620 mm, lebar bal: 1.100 mm, tinggi bal: 720 mm, berat bal: 600 kg, arus masuk: 200 A, kapasitas tangki oli: 1.250 l, berat kosong: 29.000 kg, Technical Data – Baler: Manufacturer: BOA Recycling Systems B.V. Model: Impress M75-45-A-5-1.6 Ecoline Year of manufacture: 2021 Operating hours: 2,658 hours (as of May 2024) Number of bales produced: 42,212 units (as of May 2024) Main press force: 71.2 kN (71 t) Specific compaction pressure: 9 kg/cm² Operating pressure: 280 bar Cylinder stroke: 2,200 mm Charge box dimensions: 1,620 x 1,000 mm Filling volume per press cycle: 2.4 m³ Theoretical cycle time: 21 seconds Theoretical throughput: 450 m³/hour Bale dimensions: 1,100 x 720 mm; length adjustable up to 1,400 mm Drive power: 45 kW Connected load: 100 kW Current consumption: 200 A Tying: 5-fold vertical, fully automatic; ram pre-equipped for additional 3-fold horizontal tying Throughput rates at bulk densities of: – 30 kg/m³: approx. 13.6 t/hour – 60 kg/m³: approx. 24.2 t/hour – 100 kg/m³: approx. 36.4 t/hour – 150 kg/m³: approx. 54.7 t/hour Bale weight: up to 600 kg, depending on material Hydraulic oil tank capacity: 1,250 L PLC control: Siemens S7 1500 Operator panel: Siemens SIMATIC HMI TOUCH Transport dimensions (Baler): 10,000 x 2,800 x 3,385 mm (L x W x H) Gujdeu Thcvepfx Ag Rok Baler height (assembled with feed chute): 4,743 mm Baler height (assembled with conveyor): 7,123 mm Machine weight (Baler): 29 t Noise level:

Kondisi: diremaj di bengkel (bekas), Tahun pembuatan: 2007, jam operasional: 22.605 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 100 t, lebar bukaan pengisian: 1.100 mm, panjang bukaan pengisian: 1.600 mm, lebar bal: 1.100 mm, tinggi bal: 1.100 mm, berat bal: 1.400 kg, arus masuk: 238 A, berat keseluruhan: 36.000 kg, kapasitas tangki oli: 1.300 l, For sale is a refurbished baler with 100 t press force, large-format bales 1100 x 1100 mm, 75 kW drive power and 10-way cross-tying. Technical specifications baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main press force: 100 t Pre-press force: 50 t Operating hours: 22,605 h Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Guodpfovf E Avsx Ag Rek Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Connected load: 126 kW Total current consumption: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput at bulk density of: - 30 kg/m³: approx. 16 t/h - 50 kg/m³: approx. 25 t/h - 100 kg/m³: approx. 47 t/h Bale weight up to 1,400 kg, depending on material and bale length Hydraulic oil tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operating panel: Schneider MAGELIS Touch Baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions without baler: 11,765 x 2,500 x 3,450 mm (L x W x H) Baler weight: approx. 36 t Remarks: The baler has been partially overhauled, serviced in our workshop, and tested after completion of work before being stored. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment works have been carried out: - Descaling and partial repainting of the baler. - Hydraulic oil tank drained, oil and air filters replaced. - New hydraulic oil filled. - All hydraulic hoses renewed. - Main hydraulic cylinder, two cylinders of the pre-press flap and the channel cylinder disassembled, dismantled, inspected, cylinder tubes honed, all seal kits replaced and final pressure tested. - Pre-press flap with bearings and bearing blocks disassembled. First and third circular arc segments removed and newly welded in. - Both shaft bearings for the pre-press flap renewed. - Upper material guide on the frame for the pre-press flap renewed. - Plunger disassembled, inspected and both front roller guides renewed. - Material guides and wear strips at the sides and on the bottom of the plunger cut out and newly welded in. - Horizontal and vertical needle and tying units disassembled, dismantled, inspected, plastic slide plates, bearings on twister shafts, and wire divert rollers with bearings in the needle heads renewed. - Both bronze slide rails left and right in the frame cover for the plunger renewed. - Both wire divert units left and right, including bale retaining clamps, fully renewed. - Wire infeed unit including hydraulic cylinder below the needle passes fully renewed. - Wire mark/scoring in the bottom and sidewalls of the channel welded up and smoothed. - General maintenance and service work carried out in line with manufacturer specifications. - Baler tested in manual and automatic mode, accepted and stored after completion of refurbishment works. We assume no liability for the technical details or possible errors.

Kondisi: diremajakan ulang (bekas), Tahun pembuatan: 2019, jam operasional: 3.000 h, Fungsionalitas: berfungsi sepenuhnya, gaya penekanan: 70 t, berat keseluruhan: 9.500 kg, lebar bukaan pengisian: 420 mm, panjang bukaan pengisian: 1.250 mm, Technical Data – Baling Press / Can Press / Sheet Metal Press: Manufacturer: unoTech GmbH Model: UPAXX 70 Year of manufacture: 2019 Operating hours: approx. 3,000 hours Pressing force: 700 kN at 315 bar Feed opening (hopper): 420 x 1,250 mm (D x W) Channel cross-section (bale size): 350 x 500 mm (H x W), length depending on material Drive power: 30 kW Connected load: 40 kW Total current consumption: 70 A Throughput capacity for empty beverage cans with: • One press stroke: approx. 1.7 t/h • Two press strokes: approx. 2.5 t/h Achieved compaction: approx. 1,200 kg/m³ Hydraulic oil tank capacity: 850 L Press dimensions assembled: 8,000 x 1,600 x 2,500 mm (L x W x H) Transport weight (press): approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press chamber made of wear-resistant S355 steel Material suitability: Gujdeu Th S Sepfx Ag Rok According to the manufacturer, this machine is suitable for pressing tin cans, sheet metal offcuts, steel plate, as well as aluminum, brass and copper scrap. Condition of baling press: The baling press has been completely overhauled in our workshop. The press is in very good condition and is sold with a 12-month OBM parts warranty. Remarks: Complete documentation is available (operating manual, CE declaration, electrical/hydraulic wiring diagram). Inspection by appointment is possible. We assume no liability for technical data or possible errors.

Kondisi: sangat baik (bekas), Tahun pembuatan: 2022, Fungsionalitas: berfungsi sepenuhnya, Technical Data for EPS (Styrofoam) Compactor: Manufacturer: FZ-Recycling GmbH & Co. KG, Germany Model: FZR 320 Year of Manufacture: 12/2022 Drive Power (Shredder): 4 kW Drive Power (Compacting Screw): 7.5 kW Drive Power (Hydraulic Unit for Retaining Clamp in Press Channel): 1.1 kW Total Connected Load: 12.6 kW Power Requirement: 32 A Compression Ratio of Compacted Blocks to Original Material: approx. 50:1 (depending on material) Block Weight After Compaction: approx. 300 kg/m³ (material dependent) Block Dimensions: 320 x 320 mm, length variable Throughput Capacity: approx. 100 kg/hour (depending on material) Achievable Density: approx. 250 – 300 kg/m³ Compacted blocks are stacked approx. 1400 mm high on a pallet and wrapped with stretch film. Machine Dimensions: approx. 4,600 x 1,400 x 1,980 mm (L x W x H) Transport Weight (Compactor): 1,325 kg Condition of the Compactor: The compactor was only used sporadically, is in very good condition, and available at short notice. Due to the low machine weight and forklift pockets in the transport frame, the machine is mobile and can be used directly at the material source, e.g., on the construction site. Electrical connection is via a CEE 32 A plug. Scope of Delivery: 1 piece EPS compactor, ready for connection and operation. Gusdpsu Thkaofx Ag Rsk Remarks: Complete documentation (operating manual, CE declaration, electrical/hydraulic wiring diagram) is available. Inspection possible by appointment. No liability is assumed for technical specifications or possible errors.